On Wed, Aug 07, 2024 at 12:38:48PM +0200, Frieder Schrempf wrote:
> From: Frieder Schrempf <frieder.schrempf@xxxxxxxxxx>
>
> This adds support for the Kontron Electronics i.MX8MP SMARC module
> (which uses the OSM-S i.MX8MP SoM) on the Kontron SMARC eval carrier.
>
> Signed-off-by: Frieder Schrempf <frieder.schrempf@xxxxxxxxxx>
> ---
> Changes for v2:
> * Fix GPIO labels
> * Add support for TPM chip on SMARC module
> * Disable PWM in favor of GPIO5 on SMARC carrier
> * Enable LCDIF node to make HDMI work
> * Add support for GPIO expanders on SMARC carrier
> * Remove SPI flash as its removable and should be in an overlay
> * Add CAN regulators to fix transceiver enable
> ---
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../imx8mp-kontron-smarc-eval-carrier.dts | 258 ++++++++++++++++
> .../dts/freescale/imx8mp-kontron-smarc.dtsi | 281 ++++++++++++++++++
> 3 files changed, 540 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc-eval-carrier.dts
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc.dtsi
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index e6f177e5fac26..250a7db037282 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -176,6 +176,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mp-kontron-bl-osm-s.dtb
> imx8mp-kontron-dl-dtbs += imx8mp-kontron-bl-osm-s.dtb imx8mp-kontron-dl.dtbo
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-kontron-dl.dtb
>
> +dtb-$(CONFIG_ARCH_MXC) += imx8mp-kontron-smarc-eval-carrier.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-msc-sm2s-ep1.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-navqp.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc-eval-carrier.dts b/arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc-eval-carrier.dts
> new file mode 100644
> index 0000000000000..c90cb12e91309
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc-eval-carrier.dts
> @@ -0,0 +1,258 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR MIT
> +/*
> + * Copyright (C) 2024 Kontron Electronics GmbH
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/phy/phy-imx8-pcie.h>
> +#include "imx8mp-kontron-smarc.dtsi"
> +
> +/ {
> + model = "Kontron SMARC Eval Carrier with i.MX8MP";
> + compatible = "kontron,imx8mp-smarc-eval-carrier", "kontron,imx8mp-smarc",
> + "kontron,imx8mp-osm-s", "fsl,imx8mp";
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm1 0 50000 0>;
> + brightness-levels = <0 100>;
> + num-interpolated-steps = <100>;
> + default-brightness-level = <100>;
> + enable-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
> + };
> +
> + extcon_usbc: usbc {
> + compatible = "linux,extcon-usb-gpio";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usb1_id>;
> + id-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
> + };
> +
> + sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,bitclock-master = <&codec_dai>;
> + simple-audio-card,format = "i2s";
> + simple-audio-card,frame-master = <&codec_dai>;
> + simple-audio-card,mclk-fs = <256>;
> + simple-audio-card,name = "imx8mp-wm8904";
> + simple-audio-card,routing =
> + "Headphone Jack", "HPOUTL",
> + "Headphone Jack", "HPOUTR",
> + "IN2L", "Line In Jack",
> + "IN2R", "Line In Jack",
> + "Headphone Jack", "MICBIAS",
> + "IN1L", "Headphone Jack";
> + simple-audio-card,widgets =
> + "Microphone", "Headphone Jack",
> + "Headphone", "Headphone Jack",
> + "Line", "Line In Jack";
> +
> + codec_dai: simple-audio-card,codec {
> + clocks = <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI3_MCLK1>;
> + sound-dai = <&wm8904>;
> + };
> +
> + simple-audio-card,cpu {
> + sound-dai = <&sai3>;
> + };
> + };
> +
> + can0_en_reg: can0-regulator {
Can we name it regulator-can0?
> + compatible = "regulator-fixed";
> + regulator-name = "can0_en";
> + gpio = <&expander_pm_out 6 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + can1_en_reg: can1-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "can1_en";
> + gpio = <&expander_pm_out 7 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +};
> +
> +&ecspi1 {
> + status = "okay";
> +};
> +
> +&ecspi2 {
> + status = "okay";
> +};
> +
> +&eqos {
> + status = "okay";
> +};
> +
> +&fec {
> + status = "okay";
> +};
> +
> +&flexcan1 {
> + status = "okay";
> + xceiver-supply = <&can0_en_reg>;
We would like to end property list with "status".
> +};
> +
> +&flexcan2 {
> + status = "okay";
> + xceiver-supply = <&can1_en_reg>;
> +};
> +
> +&hdmi_pvi {
> + status = "okay";
> +};
> +
> +&hdmi_tx {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hdmi>;
> + ddc-i2c-bus = <&i2c3>;
> + status = "okay";
> +};
> +
> +&hdmi_tx_phy {
> + status = "okay";
> +};
> +
> +&i2c1 {
> + status = "okay";
> +
> + expander_pm_out: tca9554@22 {
Can we use a generic node name?
> + compatible = "nxp,pca9554";
> + reg = <0x22>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-line-names = "EN_5V0_S0", "EN_3V3_S0", "EN_1V8_S0",
> + "EN_1V5_S0", "EN_12V0_PCIE", "EN_3V3_S5",
> + "CAN0_EN", "CAN1_EN";
> + status = "okay";
The "okay" status is mostly used to flip "disabled" one. Not sure we
need it here.
> + };
> +
> + expander_pm_in: tca9554@24 {
> + compatible = "nxp,pca9554";
> + reg = <0x24>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-line-names = "PG_5V0_3V3_S0", "PG_5V0_3V3_S5", "PG_1V8_S0",
> + "PG_1V5_S0", "PG_BKLT_5V", "PG_BKLT_12V";
> + status = "okay";
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> +
> + wm8904: audio-codec@1a {
> + compatible = "wlf,wm8904";
> + reg = <0x1a>;
> + #sound-dai-cells = <0>;
> + clocks = <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI3_MCLK1>;
> + clock-names = "mclk";
> + AVDD-supply = <®_vdd_1v8>;
> + CPVDD-supply = <®_vdd_1v8>;
> + DBVDD-supply = <®_vdd_1v8>;
> + DCVDD-supply = <®_vdd_1v8>;
> + MICVDD-supply = <®_vdd_3v3>;
> + };
> +
> + expander_audio: tca9554@20 {
> + compatible = "nxp,pca9554";
> + reg = <0x20>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-line-names = "I2C_SEL_CODEC_LOOPBACK", "FPAH_PRESENCE",
> + "CODEC_OPTION_SW_I2S_HDA", "LINE_IN_JD",
> + "LINE_OUT_JD", "HEADPHONES_JD", "MIC_JD";
> + status = "okay";
> + };
> +};
> +
> +&i2c3 {
> + status = "okay";
> +};
> +
> +&i2c4 {
> + status = "okay";
> +};
> +
> +&lcdif3 {
> + status = "okay";
> +};
> +
> +&pcie_phy {
> + fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_OUTPUT>;
> + fsl,clkreq-unsupported;
> + clocks = <&hsio_blk_ctrl>;
> + clock-names = "ref";
> + status = "okay";
> +};
> +
> +&pcie {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pcie>;
> + reset-gpio = <&gpio3 2 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&pwm1 {
> + status = "okay";
> +};
> +
> +&sai3 {
> + assigned-clocks = <&clk IMX8MP_CLK_SAI3>;
> + assigned-clock-parents = <&clk IMX8MP_AUDIO_PLL1_OUT>;
> + assigned-clock-rates = <24576000>;
> + fsl,sai-mclk-direction-output;
> + status = "okay";
> +};
> +
> +&uart1 {
> + uart-has-rtscts;
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart4 {
> + uart-has-rtscts;
> + status = "okay";
> +};
> +
> +&usb_dwc3_0 {
> + adp-disable;
> + hnp-disable;
> + srp-disable;
> +
Unneeded newline.
> + dr_mode = "otg";
> + extcon = <&extcon_usbc>;
> + usb-role-switch;
> + status = "okay";
> +};
> +
> +&usb_dwc3_1 {
> + status = "okay";
> +};
> +
> +&usb3_0 {
> + status = "okay";
> +};
> +
> +&usb3_1 {
> + status = "okay";
> +};
> +
> +&usb3_phy0 {
> + vbus-supply = <®_usb1_vbus>;
> + status = "okay";
> +};
> +
> +&usb3_phy1 {
> + status = "okay";
> +};
> +
> +&usdhc2 {
> + vmmc-supply = <®_vdd_3v3>;
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc.dtsi
> new file mode 100644
> index 0000000000000..b06e33862be72
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc.dtsi
> @@ -0,0 +1,281 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR MIT
> +/*
> + * Copyright (C) 2024 Kontron Electronics GmbH
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include "imx8mp-kontron-osm-s.dtsi"
> +
> +/ {
> + model = "Kontron SMARC i.MX8MP";
> + compatible = "kontron,imx8mp-smarc", "kontron,imx8mp-osm-s", "fsl,imx8mp";
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led1 {
> + label = "led1";
> + gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +};
> +
> +&ecspi1 {
> + status = "okay";
> +
> + tpm@0 {
> + compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
> + reg = <0>;
> + spi-max-frequency = <18500000>;
> + };
> +};
> +
> +&eqos { /* Second ethernet (OSM-S ETH_B) */
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_eqos_rgmii>;
> + phy-mode = "rgmii-id";
> + phy-handle = <ðphy1>;
> +
> + mdio {
> + compatible = "snps,dwmac-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy1: ethernet-phy@1 {
> + compatible = "ethernet-phy-id4f51.e91b";
> + reg = <1>;
> + pinctrl-0 = <&pinctrl_ethphy1>;
> + pinctrl-names = "default";
> + reset-assert-us = <10000>;
> + reset-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> +
> +&fec { /* First ethernet (OSM-S ETH_A) */
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet_rgmii>;
> + phy-connection-type = "rgmii-id";
> + phy-handle = <ðphy0>;
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy0: ethernet-phy@1 {
> + compatible = "ethernet-phy-id4f51.e91b";
> + reg = <1>;
> + pinctrl-0 = <&pinctrl_ethphy0>;
> + pinctrl-names = "default";
> + reset-assert-us = <10000>;
> + reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> +
> +/*
> + * Rename SoM signals according to SMARC module usage:
> + * GPIO_A_2 -> GPIO0
> + * GPIO_A_3 -> GPIO1
> + * GPIO_A_4 -> GPIO2
> + * GPIO_A_5 -> GPIO3
> + * USB_B_EN -> n.a.
> + * USB_B_ID -> n.a.
> + * USB_B_OC -> n.a.
> + */
> +&gpio1 {
> + gpio-line-names = "GPIO_A_0", "GPIO_A_1", "", "",
> + "", "GPIO0", "GPIO1", "GPIO2",
> + "GPIO3", "", "USB_A_ID", "",
> + "USB_A_EN", "USB_A_OC","CAM_MCK", "",
> + "ETH_B_MDC", "ETH_B_MDIO", "ETH_B_TXD3", "ETH_B_TXD2",
> + "ETH_B_TXD1", "ETH_B_TXD0", "ETH_B_TX_EN", "ETH_B_TX_CLK",
> + "ETH_B_RX_DV", "ETH_B_RX_CLK", "ETH_B_RXD0", "ETH_B_RXD1",
> + "ETH_B_RXD2", "ETH_B_RXD3";
> +};
> +
> +/*
> + * Rename SoM signals according to SMARC module usage:
> + * SDIO_A_CD -> SDIO_CD
> + * SDIO_A_CLK -> SDIO_CK
> + * SDIO_A_CMD -> SDIO_CMD
> + * SDIO_A_D0 -> SDIO_D0
> + * SDIO_A_D1 -> SDIO_D1
> + * SDIO_A_D2 -> SDIO_D2
> + * SDIO_A_D3 -> SDIO_D3
> + * SDIO_A_PWR_EN -> SDIO_PWR_EN
> + * SDIO_A_WP -> SDIO_WP
> + */
> +&gpio2 {
> + gpio-line-names = "", "", "", "", "", "", "", "", "", "", "", "",
> + "SDIO_CD", "SDIO_CK", "SDIO_CMD", "SDIO_D0",
> + "SDIO_D1", "SDIO_D2", "SDIO_D3", "SDIO_PWR_EN",
> + "SDIO_WP";
> +};
> +
> +/*
> + * Rename SoM signals according to SMARC module usage:
> + * PCIE_CLKREQ -> PCIE_A_CKREQ
> + * PCIE_A_PERST -> PCIE_A_RST
> + * SDIO_B_D5 -> n.a.
> + * SDIO_B_D6 -> n.a.
> + * SDIO_B_D7 -> n.a.
> + * SPI_A_WP -> n.a.
> + * SPI_A_HOLD -> n.a.
> + * UART_B_RTS -> SER2_RTS
> + * UART_B_CTS -> SER2_CTS
> + * SDIO_B_D0 -> GPIO8
> + * SDIO_B_D1 -> GPIO9
> + * SDIO_B_D2 -> GPIO10
> + * SDIO_B_D3 -> GPIO11
> + * SDIO_B_WP -> n.a.
> + * SDIO_B_D4 -> n.a.
> + * PCIE_SM_ALERT -> SMB_ALERT
> + * SDIO_B_CLK -> GPIO6
> + * SDIO_B_CMD -> GPIO7
> + * GPIO_B_0 -> LCD0_BKLT_EN
> + * GPIO_B_1 -> LCD1_BKLT_EN
> + * BOOT_SEL0 -> BOOT_SEL2
> + * SDIO_B_CD -> n.a.
> + * SDIO_B_PWR_EN -> n.a.
> + * HDMI_CEC -> n.a.
> + * SDIO_B_PWR_EN -> n.a.
> + */
> +&gpio3 {
> + pinctrl-0 = <&pinctrl_gpio3>, <&pinctrl_gpio3_smarc>;
> + gpio-line-names = "PCIE_WAKE", "PCIE_A_CKREQ", "PCIE_A_RST", "",
> + "", "", "", "",
> + "SER2_RTS", "SER2_CTS", "GPIO8", "GPIO9",
> + "GPIO10", "GPIO11", "", "",
> + "SMB_ALERT", "GPIO6", "GPIO7", "LCD0_BKLT_EN",
> + "LCD1_BKLT_EN", "", "BOOT_SEL2", "BOOT_SEL1",
> + "", "", "", "",
> + "", "HDMI_HPD";
> +};
> +
> +/*
> + * Rename SoM signals according to SMARC module usage:
> + * GPIO_B_5 -> n.a.
> + * GPIO_B_6 -> n.a.
> + * GPIO_B_7 -> n.a.
> + * GPIO_C_0 -> LED
> + * GPIO_B_3 -> ETH2_INT
> + * GPIO_B_4 -> USB_HUB_RST
> + * GPIO_B_2 -> ETH1_INT
> + * GPIO_A_6 -> GPIO4
> + * CAN_A_TX -> CAN0_TX
> + * UART_A_CTS -> SER0_CTS
> + * UART_A_RTS -> SER0_RTS
> + * CAN_A_RX -> CAN0_RX
> + * CAN_B_TX -> CAN1_TX
> + * CAN_B_RX -> CAN1_RX
> + * GPIO_A_7 -> TEST
> + * I2S_A_DATA_IN -> I2S0_SDIN
> + * I2S_LRCLK -> I2S0_LRCK
> + */
> +&gpio4 {
> + gpio-line-names = "", "", "", "LED",
> + "ETH_A_MDC", "ETH_A_MDIO", "ETH_A_RXD0", "ETH_A_RXD1",
> + "ETH_A_RXD2", "ETH_A_RXD3", "ETH_A_RX_DV", "ETH_A_RX_CLK",
> + "ETH_A_TXD0", "ETH_A_TXD1", "ETH_A_TXD2", "ETH_A_TXD3",
> + "ETH_A_TX_EN", "ETH_A_TX_CLK", "ETH2_INT", "USB_HUB_RST",
> + "ETH1_INT", "GPIO4", "CAN0_TX", "SER0_CTS",
> + "SER0_RTS", "CAN0_RX", "CAN1_TX", "CAN1_RX",
> + "TEST", "CARRIER_PWR_EN", "I2S0_SDIN", "I2S0_LRCK";
> +};
> +
> +/*
> + * Rename SoM signals according to SMARC module usage:
> + * I2S_BITCLK -> I2S0_CK
> + * I2S_A_DATA_OUT -> I2S0_SDOUT
> + * I2S_MCLK -> AUDIO_MCK
> + * PWM_2 -> GPIO5
> + * PWM_1 -> LCD1_BKLT_PWM
> + * PWM_0 -> LCD0_BKLT_PWM
> + * SPI_A_SCK -> SPI0_CK
> + * SPI_A_SDO -> SPI0_DO
> + * SPI_A_SDI -> SPI0_DIN
> + * SPI_A_CS0 -> SPI0_CS0
> + * SPI_B_SCK -> ESPI_CK
> + * SPI_B_SDO -> ESPI_IO_0
> + * SPI_B_SDI -> ESPI_IO_1
> + * SPI_B_CS0 -> ESPI_CS0
> + * I2C_A_SCL -> I2C_PM_CK
> + * I2C_A_SDA -> I2C_PM_DAT
> + * I2C_B_SCL -> I2C_GP_CK
> + * I2C_B_SDA -> I2C_GP_DAT
> + * PCIE_SMCLK -> HDMI_CTRL_CK
> + * PCIE_SMDAT -> HDMI_CTRL_DAT
> + * I2C_CAM_SCL -> I2C_CAM1_CK
> + * I2C_CAM_SDA -> I2C_CAM1_DAT
> + * UART_A_RX -> SER0_RX
> + * UART_A_TX -> SER0_TX
> + * UART_C_RX -> SER3_RX
> + * UART_C_TX -> SER3_TX
> + * UART_CON_RX -> SER1_RX
> + * UART_CON_TX -> SER1_TX
> + * UART_B_RX -> SER2_RX
> + * UART_B_TX -> SER2_TX
> + */
> +&gpio5 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio5_smarc>;
> + gpio-line-names = "I2S0_CK", "I2S0_SDOUT", "AUDIO_MCK", "GPIO5",
> + "LCD1_BKLT_PWM", "LCD0_BKLT_PWM", "SPI0_CK", "SPI0_DO",
> + "SPI0_DIN", "SPI0_CS0", "ESPI_CK", "ESPI_IO_0",
> + "ESPI_IO_1", "ESPI_CS0", "I2C_PM_CK", "I2C_PM_DAT",
> + "I2C_GP_CK", "I2C_GP_DAT", "HDMI_CTRL_CK", "HDMI_CTRL_DAT",
> + "I2C_CAM1_CK", "I2C_CAM1_DAT", "SER0_RX", "SER0_TX",
> + "SER3_RX", "SER3_TX", "SER1_RX", "SER1_TX",
> + "SER2_RX", "SER2_TX";
> +};
> +
> +&usb_dwc3_1 {
> + dr_mode = "host";
> +
Nit: the newline is not super helpful.
Shawn
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + usb1@1 {
> + compatible = "usb424,2514";
> + reg = <1>;
> + reset-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
> + };
> +};
> +
> +&usb3_1 {
> + fsl,disable-port-power-control;
> + fsl,permanently-attached;
> +};
> +
> +&iomuxc {
> + pinctrl_ethphy0: ethphy0grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_GPIO1_IO01__GPIO1_IO01 0x46
> + >;
> + };
> +
> + pinctrl_ethphy1: ethphy1grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_GPIO1_IO00__GPIO1_IO00 0x46
> + >;
> + };
> +
> + pinctrl_gpio3_smarc: gpio3smarcgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_NAND_DATA04__GPIO3_IO10 0x1d0 /* SMARC GPIO8 */
> + MX8MP_IOMUXC_NAND_DATA05__GPIO3_IO11 0x1d0 /* SMARC GPIO9 */
> + MX8MP_IOMUXC_NAND_DATA06__GPIO3_IO12 0x1d0 /* SMARC GPIO10 */
> + MX8MP_IOMUXC_NAND_DATA07__GPIO3_IO13 0x1d0 /* SMARC GPIO11 */
> + MX8MP_IOMUXC_NAND_WE_B__GPIO3_IO17 0x190 /* SMARC GPIO6 */
> + MX8MP_IOMUXC_NAND_WP_B__GPIO3_IO18 0x1d0 /* SMARC GPIO7 */
> + >;
> + };
> +
> + pinctrl_gpio5_smarc: gpio5smarcgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SPDIF_RX__GPIO5_IO04 0x1d0 /* SMARC GPIO5 */
> + >;
> + };
> +};
> --
> 2.45.2
>
