On 06/03/15 17:18, Brian Norris wrote:
> Signed-off-by: Brian Norris <computersforpeace@xxxxxxxxx>
Reviewed-by: Florian Fainelli <f.fainelli@xxxxxxxxx>
> ---
> .../devicetree/bindings/mtd/brcmstb_nand.txt | 109 +++++++++++++++++++++
> 1 file changed, 109 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mtd/brcmstb_nand.txt
>
> diff --git a/Documentation/devicetree/bindings/mtd/brcmstb_nand.txt b/Documentation/devicetree/bindings/mtd/brcmstb_nand.txt
> new file mode 100644
> index 000000000000..933d44943cbb
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mtd/brcmstb_nand.txt
> @@ -0,0 +1,109 @@
> +* Broadcom STB NAND Controller
> +
> +The Broadcom Set-Top Box NAND controller supports low-level access to raw NAND
> +flash chips. It has a memory-mapped register interface for both control
> +registers and for its data input/output buffer. On some SoCs, this controller is
> +paired with a custom DMA engine (inventively named "Flash DMA") which supports
> +basic PROGRAM and READ functions, among other features.
> +
> +This controller was originally designed for STB SoCs (BCM7xxx) but is now
> +available on a variety of Broadcom SoCs, including some BCM3xxx, BCM63xx, and
> +iProc/Cygnus. Its history includes several similar (but not fully register
> +compatible) versions.
> +
> +Required properties:
> +- compatible : should contain "brcm,brcmnand" and an appropriate version
> + compatibility string, like "brcm,brcmnand-v7.0"
> + Possible values:
> + brcm,brcmnand-v4.0
> + brcm,brcmnand-v5.0
> + brcm,brcmnand-v6.0
> + brcm,brcmnand-v7.0
> + brcm,brcmnand-v7.1
> + brcm,brcmnand
> +- reg : the register start and length for NAND register region.
> + (optional) Flash DMA register range (if present)
> + (optional) NAND flash cache range (if at non-standard offset)
> +- reg-names : a list of the names corresponding to the previous register
> + ranges. Should contain "nand" and (optionally)
> + "flash-dma" and/or "nand-cache".
> +- interrupts : The NAND CTLRDY interrupt and (if Flash DMA is available)
> + FLASH_DMA_DONE
> +- interrupt-names : May be "nand_ctlrdy" or "flash_dma_done"
> +- interrupt-parent : See standard interrupt bindings
> +- #address-cells : <1> - subnodes give the chip-select number
> +- #size-cells : <0>
> +
> +Optional properties:
> +- brcm,nand-has-wp : Some versions of this IP include a write-protect
> + (WP) control bit. It is always available on >=
> + v7.0. Use this property to describe the rare
> + earlier versions of this core that include WP
> +
> +* NAND chip-select
> +
> +Each controller (compatible: "brcm,brcmnand") may contain one or more subnodes
> +to represent enabled chip-selects which (may) contain NAND flash chips. Their
> +properties are as follows.
> +
> +Required properties:
> +- compatible : should contain "brcm,nandcs"
> +- reg : a single integer representing the chip-select
> + number (e.g., 0, 1, 2, etc.)
> +- #address-cells : see partition.txt
> +- #size-cells : see partition.txt
> +- nand-ecc-strength : see nand.txt
> +- nand-ecc-step-size : must be 512 or 1024. See nand.txt
> +
> +Optional properties:
> +- nand-on-flash-bbt : boolean, to enable the on-flash BBT for this
> + chip-select. See nand.txt
> +- brcm,nand-oob-sector-size : integer, to denote the spare area sector size
> + expected for the ECC layout in use. This size, in
> + addition to the strength and step-size,
> + determines how the hardware BCH engine will lay
> + out the parity bytes it stores on the flash.
> + This property can be automatically determined by
> + the flash geometry (particularly the NAND page
> + and OOB size) in many cases, but when booting
> + from NAND, the boot controller has only a limited
> + number of available options for its default ECC
> + layout.
> +
> +Each nandcs device node may optionally contain sub-nodes describing the flash
> +partition mapping. See partition.txt for more detail.
> +
> +Example:
> +
> +nand@f0442800 {
> + compatible = "brcm,brcmnand-v7.0", "brcm,brcmnand";
> + reg = <0xF0442800 0x600>,
> + <0xF0443000 0x100>;
> + reg-names = "nand", "flash-dma";
> + interrupt-parent = <&hif_intr2_intc>;
> + interrupts = <24>, <4>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + nandcs@1 {
> + compatible = "brcm,nandcs";
> + reg = <1>; // Chip select 1
> + nand-on-flash-bbt;
> + nand-ecc-strength = <12>;
> + nand-ecc-step-size = <512>;
> +
> + // Partitions
> + #address-cells = <1>; // <2>, for 64-bit offset
> + #size-cells = <1>; // <2>, for 64-bit length
> + flash0.rootfs@0 {
> + reg = <0 0x10000000>;
> + };
> + flash0@0 {
> + reg = <0 0>; // MTDPART_SIZ_FULL
> + };
> + flash0.kernel@10000000 {
> + reg = <0x10000000 0x400000>;
> + };
> + };
> +};
>
--
Florian
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
