[PATCH v2 3/4] arm64: dts: imx8mm-kontron: Add support for display bridges on BL i.MX8MM

[Frieder Schrempf <frieder@xxxxxxx>]

From: Frieder Schrempf <frieder.schrempf@xxxxxxxxxx>

The Kontron Electronics BL i.MX8MM has oboard disply bridges for
DSI->HDMI and DSI->LVDS conversion. The DSI interface is muxed by
a GPIO-controlled switch to one of these two bridges.

By default the HDMI bridge is enabled. The LVDS bridge can be
selected by loading an additional (panel-specific) overlay.

Signed-off-by: Frieder Schrempf <frieder.schrempf@xxxxxxxxxx>
---
Changes for v2:
* Remove blank lines from hdmi node
* Fix order of lvds and hdmi nodes within i2c
* Remove the unneeded deletion of samsung,pll-clock-frequency
* Use the existing MIPI DSI output port from imx8mm.dtsi
---
 .../boot/dts/freescale/imx8mm-kontron-bl.dts  | 131 ++++++++++++++++++
 1 file changed, 131 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
index aab8e24216501..a8ef4fba16a9e 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
@@ -25,6 +25,17 @@ osc_can: clock-osc-can {
 		clock-output-names = "osc-can";
 	};
 
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_in_conn: endpoint {
+				remote-endpoint = <&bridge_out_conn>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -132,6 +143,86 @@ ethphy: ethernet-phy@0 {
 	};
 };
 
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio4>;
+
+	dsi_mux_sel_hdmi: dsi-mux-sel-hdmi-hog {
+		gpio-hog;
+		gpios = <14 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "dsi-mux-sel";
+	};
+
+	dsi_mux_sel_lvds: dsi-mux-sel-lvds-hog {
+		gpio-hog;
+		gpios = <14 GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "dsi-mux-sel";
+		status = "disabled";
+	};
+
+	dsi-mux-oe-hog {
+		gpio-hog;
+		gpios = <15 GPIO_ACTIVE_LOW>;
+		output-high;
+		line-name = "dsi-mux-oe";
+	};
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	lvds: bridge@2c {
+		compatible = "ti,sn65dsi84";
+		reg = <0x2c>;
+		enable-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sn65dsi84>;
+		status = "disabled";
+	};
+
+	hdmi: hdmi@39 {
+		compatible = "adi,adv7535";
+		reg = <0x39>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_adv7535>;
+		adi,dsi-lanes = <4>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+		a2vdd-supply = <&reg_vdd_1v8>;
+		avdd-supply = <&reg_vdd_1v8>;
+		dvdd-supply = <&reg_vdd_1v8>;
+		pvdd-supply = <&reg_vdd_1v8>;
+		v1p2-supply = <&reg_vdd_1v8>;
+		v3p3-supply = <&reg_vdd_3v3>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				bridge_in_dsi_hdmi: endpoint {
+					remote-endpoint = <&mipi_dsi_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				bridge_out_conn: endpoint {
+					remote-endpoint = <&hdmi_in_conn>;
+				};
+			};
+		};
+	};
+};
+
 &i2c4 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default";
@@ -144,6 +235,19 @@ rx8900: rtc@32 {
 	};
 };
 
+&lcdif {
+	status = "okay";
+};
+
+&mipi_dsi {
+	samsung,esc-clock-frequency = <54000000>;
+	status = "okay";
+};
+
+&mipi_dsi_out {
+	remote-endpoint = <&bridge_in_dsi_hdmi>;
+};
+
 &pwm2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
@@ -207,6 +311,12 @@ &iomuxc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gpio>;
 
+	pinctrl_adv7535: adv7535grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_TXD4_GPIO4_IO16		0x19
+		>;
+	};
+
 	pinctrl_can: cangrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28		0x19
@@ -277,6 +387,20 @@ MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x19
 		>;
 	};
 
+	pinctrl_gpio4: gpio4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_TXD2_GPIO4_IO14		0x19
+			MX8MM_IOMUXC_SAI1_TXD3_GPIO4_IO15		0x19
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL			0x40000083
+			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA			0x40000083
+		>;
+	};
+
 	pinctrl_i2c4: i2c4grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x40000083
@@ -290,6 +414,13 @@ MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT			0x19
 		>;
 	};
 
+	pinctrl_sn65dsi84: sn65dsi84grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI2_TXD0_GPIO4_IO26		0x19
+			MX8MM_IOMUXC_SD2_WP_GPIO2_IO20			0x19
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x0
-- 
2.46.0