Update the DT to match newest Data Modul i.MX8M Mini eDM SBC rev.A01
board which implements PHY changes. Keep some of the rev.900 PHY node
in the DT so that a DTO can be used to support rev.900 boards easily.
Signed-off-by: Marek Vasut <marex@xxxxxxx>
---
Cc: Conor Dooley <conor+dt@xxxxxxxxxx>
Cc: Fabio Estevam <festevam@xxxxxxxxx>
Cc: Krzysztof Kozlowski <krzk+dt@xxxxxxxxxx>
Cc: Pengutronix Kernel Team <kernel@xxxxxxxxxxxxxx>
Cc: Rob Herring <robh@xxxxxxxxxx>
Cc: Sascha Hauer <s.hauer@xxxxxxxxxxxxxx>
Cc: Shawn Guo <shawnguo@xxxxxxxxxx>
Cc: devicetree@xxxxxxxxxxxxxxx
Cc: imx@xxxxxxxxxxxxxxx
Cc: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
Cc: linux-kernel@xxxxxxxxxxxxxxx
---
.../freescale/imx8mm-data-modul-edm-sbc.dts | 19 +++++++++++++++++--
1 file changed, 17 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts
index b1f2beb40a98f..472c584fb3bd2 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts
@@ -168,7 +168,7 @@ &fec1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_fec1>;
phy-mode = "rgmii-id";
- phy-handle = <&fec1_phy>;
+ phy-handle = <&fec1_phy_bcm>;
phy-supply = <&buck4_reg>;
fsl,magic-packet;
status = "okay";
@@ -178,7 +178,7 @@ mdio {
#size-cells = <0>;
/* Atheros AR8031 PHY */
- fec1_phy: ethernet-phy@0 {
+ fec1_phy_ath: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <0>;
/*
@@ -191,6 +191,7 @@ fec1_phy: ethernet-phy@0 {
reset-deassert-us = <10000>;
qca,keep-pll-enabled;
vddio-supply = <&vddio>;
+ status = "disabled";
vddio: vddio-regulator {
regulator-name = "VDDIO";
@@ -202,6 +203,20 @@ vddh: vddh-regulator {
regulator-name = "VDDH";
};
};
+
+ /* Broadcom BCM54213PE PHY */
+ fec1_phy_bcm: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ /*
+ * Dedicated ENET_INT# and ENET_WOL# signals are
+ * unused, the PHY does not provide cable detect
+ * interrupt.
+ */
+ reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <10000>;
+ };
};
};
--
2.43.0
