Add support for TypeC1 found on Forlinx OK3588-C. Powering the board
using this port is not supported, so set power-role to source.
Signed-off-by: Dmitry Yashin <dmt.yashin@xxxxxxxxx>
---
.../boot/dts/rockchip/rk3588-ok3588-c.dts | 107 ++++++++++++++++++
1 file changed, 107 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/rk3588-ok3588-c.dts b/arch/arm64/boot/dts/rockchip/rk3588-ok3588-c.dts
index 1b6bfa2b1a69..c71fbf3562b4 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588-ok3588-c.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588-ok3588-c.dts
@@ -113,6 +113,18 @@ vbus5v0_typec0: vbus5v0-typec0-regulator {
vin-supply = <&vcc5v0_sys>;
};
+ vbus5v0_typec1: vbus5v0-typec1-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vbus5v0_typec1";
+ enable-active-high;
+ gpio = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&typec5v_1_pwren>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
vcc12v_dcin: vcc12v-dcin-regulator {
compatible = "regulator-fixed";
regulator-name = "vcc12v_dcin";
@@ -286,6 +298,51 @@ &i2c5 {
pinctrl-names = "default";
pinctrl-0 = <&i2c5m2_xfer>;
+ usbc1: usb-typec@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <RK_PB3 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usbc1_int>;
+ vbus-supply = <&vbus5v0_typec1>;
+
+ usb_con1: connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ data-role = "dual";
+ power-role = "source";
+ source-pdos =
+ <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ usbc1_hs: endpoint {
+ remote-endpoint = <&usb_host1_xhci_drd_sw>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ usbc1_ss: endpoint {
+ remote-endpoint = <&usbdp_phy1_typec_ss>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ usbc1_sbu: endpoint {
+ remote-endpoint = <&usbdp_phy1_typec_sbu>;
+ };
+ };
+ };
+ };
+ };
+
pcf8563: rtc@51 {
compatible = "nxp,pcf8563";
reg = <0x51>;
@@ -413,9 +470,17 @@ typec5v_0_pwren: typec5v-0-pwren {
rockchip,pins = <0 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
};
+ typec5v_1_pwren: typec5v-1-pwren {
+ rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
usbc0_int: usbc0-int {
rockchip,pins = <1 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
};
+
+ usbc1_int: usbc1-int {
+ rockchip,pins = <1 RK_PB3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
};
};
@@ -454,6 +519,14 @@ &u2phy0_otg {
status = "okay";
};
+&u2phy1 {
+ status = "okay";
+};
+
+&u2phy1_otg {
+ status = "okay";
+};
+
&u2phy2 {
status = "okay";
};
@@ -493,6 +566,29 @@ usbdp_phy0_typec_sbu: endpoint@1 {
};
};
+&usbdp_phy1 {
+ mode-switch;
+ orientation-switch;
+ sbu1-dc-gpios = <&gpio4 RK_PA1 GPIO_ACTIVE_HIGH>;
+ sbu2-dc-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usbdp_phy1_typec_ss: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&usbc1_ss>;
+ };
+
+ usbdp_phy1_typec_sbu: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&usbc1_sbu>;
+ };
+ };
+};
+
&usb_host0_ehci {
status = "okay";
};
@@ -519,3 +615,14 @@ &usb_host1_ehci {
&usb_host1_ohci {
status = "okay";
};
+
+&usb_host1_xhci {
+ usb-role-switch;
+ status = "okay";
+
+ port {
+ usb_host1_xhci_drd_sw: endpoint {
+ remote-endpoint = <&usbc1_hs>;
+ };
+ };
+};
--
2.39.2
