On 7/30/2024 3:23 PM, Manorit Chawdhry wrote:
Removes bootph-* properties from parent nodes and aligns the bootph-* to
other u-boot.dtsi
Signed-off-by: Manorit Chawdhry <m-chawdhry@xxxxxx>
---
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 9 +--------
arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi | 8 ++++----
2 files changed, 5 insertions(+), 12 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index ffa38f41679d..311844490027 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -461,7 +461,6 @@ J784S4_IOPAD(0x078, PIN_OUTPUT, 1) /* (AH37) MCAN2_RX.AUDIO_EXT_REFCLK1 */
};
main_pmx0 has bootph-all in parent node, please consider to clean that
as well
&wkup_pmx2 {
- bootph-all;
wkup_uart0_pins_default: wkup-uart0-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -577,7 +576,6 @@ J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
};
&wkup_pmx0 {
- bootph-all;
mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -597,7 +595,6 @@ J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
};
&wkup_pmx1 {
- bootph-all;
mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -668,6 +665,7 @@ bucka12: buck12 {
regulator-max-microvolt = <1100000>;
regulator-boot-on;
regulator-always-on;
+ bootph-pre-ram;
};
bucka3: buck3 {
@@ -769,18 +767,15 @@ &ufs_wrapper {
};
&fss {
- bootph-all;
status = "okay";
};
&ospi0 {
- bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_fss0_ospi0_pins_default>, <&mcu_fss0_ospi0_1_pins_default>;
flash@0 {
- bootph-all;
compatible = "jedec,spi-nor";
reg = <0x0>;
spi-tx-bus-width = <8>;
@@ -837,13 +832,11 @@ partition@3fc0000 {
};
&ospi1 {
- bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
flash@0 {
- bootph-all;
compatible = "jedec,spi-nor";
reg = <0x0>;
spi-tx-bus-width = <1>;
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
index f3a6ed1c979d..3f89277e3c2c 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
@@ -7,7 +7,6 @@
&cbass_mcu_wakeup {
sms: system-controller@44083000 {
- bootph-all;
compatible = "ti,k2g-sci";
ti,host-id = <12>;
@@ -39,7 +38,6 @@ k3_reset: reset-controller {
};
wkup_conf: bus@43000000 {
- bootph-all;
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
@@ -65,6 +63,7 @@ secure_proxy_sa3: mailbox@43600000 {
* firmware on non-MPU processors
*/
status = "disabled";
+ bootph-pre-ram;
};
mcu_ram: sram@41c00000 {
@@ -175,10 +174,10 @@ mcu_timer0: timer@40400000 {
ti,timer-pwm;
/* Non-MPU Firmware usage */
status = "reserved";
+ bootph-all;
both nodes mcu_timer0 and mcu_timer1 as marked as
/* Non-MPU Firmware usage */, Please provide some message added bootph in first and removed from second
};
mcu_timer1: timer@40410000 {
- bootph-all;
compatible = "ti,am654-timer";
reg = <0x00 0x40410000 0x00 0x400>;
interrupts = <GIC_SPI 817 IRQ_TYPE_LEVEL_HIGH>;
@@ -458,7 +457,6 @@ mcu_spi2: spi@40320000 {
};
[..]
