On Thu, Jun 27, 2024 at 09:56:11PM +0530, Ayush Singh wrote: > Add DT bindings for mikroBUS interface. MikroBUS is an open standard > developed by MikroElektronika for connecting add-on boards to > microcontrollers or microprocessors. > > mikroBUS is a connector and does not have a controller. Instead the > software is responsible for identification of board and setting up uart, > spi, i2c, pwm and other buses. Additionally, some new mikroBUS boards > contain 1-wire EEPROM that contains a manifest to describe the addon > board to provide plug and play capabilities. > > A mikroBUS addon board is free to leave some of the pins unused which > are marked as NC or Not Connected. > > Some of the pins might need to be configured as GPIOs deviating from their > reserved purposes Eg: SHT15 Click where the SCL and SDA Pins need to be > configured as GPIOs for the driver (drivers/hwmon/sht15.c) to work. > > For some add-on boards the driver may not take care of some additional > signals like reset/wake-up/other. Eg: ENC28J60 click where the reset line > (RST pin on the mikrobus port) needs to be pulled high. > > Some SPI addon boards use other pins like RST, AN etc as chipselect (eg. > SPI Extend Click). Thus, `spi-cs` and `spi-cs-names` property is added > to allow mikroBUS addon board to specify chipselect by name. > > Here's the list of pins in mikroBUS connector: > AN - Analog > RST - Reset > CS - SPI Chip Select > SCK - SPI Clock > MISO - SPI Master Input Slave Output > MOSI - SPI Master Output Slave Input > +3.3V - VCC-3.3V power > GND - Reference Ground > PWM - PWM output > INT - Hardware Interrupt > RX - UART Receive > TX - UART Transmit > SCL - I2C Clock > SDA - I2C Data > +5V - VCC-5V power > GND - Reference Ground > > Link: https://www.mikroe.com/mikrobus > Link: > https://download.mikroe.com/documents/standards/mikrobus/mikrobus-standard-specification-v200.pdf > mikroBUS specification > Link: https://www.mikroe.com/sht1x-click SHT15 Click > Link: https://www.mikroe.com/eth-click ENC28J60 Click > Link: https://www.mikroe.com/spi-extend-click SPI Extend Click > > Co-developed-by: Vaishnav M A <vaishnav@xxxxxxxxxxxxxxx> > Signed-off-by: Vaishnav M A <vaishnav@xxxxxxxxxxxxxxx> > Signed-off-by: Ayush Singh <ayush@xxxxxxxxxxxxxxx> > --- > .../bindings/connector/mikrobus-connector.yaml | 107 +++++++++++++++++++++ > MAINTAINERS | 6 ++ > 2 files changed, 113 insertions(+) > > diff --git a/Documentation/devicetree/bindings/connector/mikrobus-connector.yaml b/Documentation/devicetree/bindings/connector/mikrobus-connector.yaml > new file mode 100644 > index 000000000000..033479f8604f > --- /dev/null > +++ b/Documentation/devicetree/bindings/connector/mikrobus-connector.yaml > @@ -0,0 +1,107 @@ > +# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/connector/mikrobus-connector.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: mikroBUS add-on board connector > + > +maintainers: > + - Ayush Singh <ayush@xxxxxxxxxxxxxxx> > + > +properties: > + compatible: > + const: mikrobus-connector > + > + pinctrl-0: true > + pinctrl-1: true > + pinctrl-2: true > + pinctrl-3: true > + pinctrl-4: true > + pinctrl-5: true > + pinctrl-6: true > + pinctrl-7: true > + pinctrl-8: true > + > + pinctrl-names: > + minItems: 1 > + maxItems: 9 > + items: > + enum: [default, pwm_default, pwm_gpio, uart_default, uart_gpio, i2c_default, i2c_gpio, spi_default, > + spi_gpio] Generally, each pinctrl-N is mutually exclusive. It looks like here you want multiple states active at one time. Does this work? > + > + spi-controller: > + description: spi-controller of mikroBUS SPI pins along with cs pins. > + $ref: /schemas/types.yaml#/definitions/phandle > + > + spi-cs: > + description: spi chip-select corresponding to the chip-selects on the mikrobus socket. Wrap lines at 80 char. The array index is the chip-select number on the connector and the value is the host SPI controller CS numbers? Or the other way around? This needs a better description. > + $ref: /schemas/types.yaml#/definitions/uint32-array Maximum number of entries? > + > + spi-cs-names: > + minItems: 1 > + maxItems: 12 > + items: > + enum: [default, pwm, int, rx, tx, scl, sda, an, rst, sck, cipo, copi] > + > + i2c-controller: > + description: i2c controller attached to the mikrobus socket. > + $ref: /schemas/types.yaml#/definitions/phandle i2c-bus is the somewhat standard property for this. Really, I'd expect connectors to look something like this: connector { i2c-0 { i2c-bus = <&i2c3>; #address-cells = <1>; #size-cells = <0>; device@12 { compatible = "some-i2c-device"; }; }; }; That form allows for multiple buses (of the same type or different) on the connector. > + > + uart-controller: > + description: uart controller attached to the mikrobus socket > + $ref: /schemas/types.yaml#/definitions/phandle > + > + pwms: > + description: the pwm-controller corresponding to the mikroBUS PWM pin. > + maxItems: 1 > + > + mikrobus-gpios: > + minItems: 1 > + maxItems: 12 > + > + mikrobus-gpio-names: The GPIO binding does not work this way as the name is in the property. Either drop if you want to keep the array or you have to do something like this: pwm-gpios int-gpios rx-gpios Really, the intention was for connectors to use gpio-map property to renumber GPIOs relative to the connector. > + minItems: 1 > + maxItems: 12 > + items: > + enum: [pwm, int, rx, tx, scl, sda, an, rst, cs, sck, cipo, copi] > + > + board: > + description: board attached to mikrobus connector > + $ref: /schemas/types.yaml#/definitions/phandle-array What is this for? > + > +required: > + - compatible > + - pinctrl-0 > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/gpio/gpio.h> > + mikrobus { > + compatible = "mikrobus-connector"; > + pinctrl-names = "default", "pwm_default", "pwm_gpio","uart_default", "uart_gpio", "i2c_default", > + "i2c_gpio", "spi_default", "spi_gpio"; > + pinctrl-0 = <&P2_03_gpio_input_pin &P1_04_gpio_pin &P1_02_gpio_pin>; > + pinctrl-1 = <&P2_01_pwm_pin>; > + pinctrl-2 = <&P2_01_gpio_pin>; > + pinctrl-3 = <&P2_05_uart_pin &P2_07_uart_pin>; > + pinctrl-4 = <&P2_05_gpio_pin &P2_07_gpio_pin>; > + pinctrl-5 = <&P2_09_i2c_pin &P2_11_i2c_pin>; > + pinctrl-6 = <&P2_09_gpio_pin &P2_11_gpio_pin>; > + pinctrl-7 = <&P1_12_spi_pin &P1_10_spi_pin &P1_08_spi_sclk_pin &P1_06_spi_cs_pin>; > + pinctrl-8 = <&P1_12_gpio_pin &P1_10_gpio_pin &P1_08_gpio_pin &P1_06_gpio_pin>; > + pwms = <&ehrpwm1 0 500000 0>; > + i2c-controller = <&i2c1>; > + uart-controller = <&uart1>; > + spi-controller = <&spi1>; > + spi-cs = <0 1>; > + spi-cs-names = "default", "rst"; > + mikrobus-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>, <&gpio0 23 GPIO_ACTIVE_HIGH>, > + <&gpio0 30 GPIO_ACTIVE_HIGH>, <&gpio0 31 GPIO_ACTIVE_HIGH>, > + <&gpio0 15 GPIO_ACTIVE_HIGH>, <&gpio0 14 GPIO_ACTIVE_HIGH>, > + <&gpio0 4 GPIO_ACTIVE_HIGH>, <&gpio0 3 GPIO_ACTIVE_HIGH>, > + <&gpio0 2 GPIO_ACTIVE_HIGH>, <&gpio0 5 GPIO_ACTIVE_HIGH>, > + <&gpio2 25 GPIO_ACTIVE_HIGH>, <&gpio2 3 GPIO_ACTIVE_HIGH>; > + }; > diff --git a/MAINTAINERS b/MAINTAINERS > index 807feae089c4..8e4115e93aeb 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -15108,6 +15108,12 @@ M: Oliver Neukum <oliver@xxxxxxxxxx> > S: Maintained > F: drivers/usb/image/microtek.* > > +MIKROBUS > +M: Ayush Singh <ayush@xxxxxxxxxxxxxxx> > +M: Vaishnav M A <vaishnav@xxxxxxxxxxxxxxx> > +S: Maintained > +F: Documentation/devicetree/bindings/connector/mikrobus-connector.yaml > + > MIKROTIK CRS3XX 98DX3236 BOARD SUPPORT > M: Luka Kovacic <luka.kovacic@xxxxxxxxxx> > M: Luka Perkov <luka.perkov@xxxxxxxxxx> > > -- > 2.45.2 >
