[PATCH RFC 7/7] pci: pwrctl: Add power control driver for qps615

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



QPS615 switch needs to configured after powering on and before
PCIe link was up.

As the PCIe controller driver already enables the PCIe link training
at the host side, stop the link training.
Otherwise the moment we turn on the switch it will participate in
the link training and link may come before switch is configured through
i2c.

The switch can be configured different ways like changing de-emphasis
settings of the switch, disabling unused ports etc and these settings
can vary from board to board, for that reason the sequence is taken
from the firmware file which contains the address of the slave, to address
and data to be written to the switch. The driver reads the firmware file
and parses them to apply those configurations to the switch.

Signed-off-by: Krishna chaitanya chundru <quic_krichai@xxxxxxxxxxx>
---
 drivers/pci/pwrctl/Kconfig             |   7 +
 drivers/pci/pwrctl/Makefile            |   1 +
 drivers/pci/pwrctl/pci-pwrctl-qps615.c | 278 +++++++++++++++++++++++++++++++++
 3 files changed, 286 insertions(+)

diff --git a/drivers/pci/pwrctl/Kconfig b/drivers/pci/pwrctl/Kconfig
index f1b824955d4b..a419b250006d 100644
--- a/drivers/pci/pwrctl/Kconfig
+++ b/drivers/pci/pwrctl/Kconfig
@@ -14,4 +14,11 @@ config PCI_PWRCTL_PWRSEQ
 	  Enable support for the PCI power control driver for device
 	  drivers using the Power Sequencing subsystem.
 
+config PCI_PWRCTL_QPS615
+	tristate "PCI Power Control driver for QPS615"
+	select PCI_PWRCTL
+	help
+	  Enable support for the PCI power control driver for QPS615 and
+	  configures it.
+
 endmenu
diff --git a/drivers/pci/pwrctl/Makefile b/drivers/pci/pwrctl/Makefile
index d308aae4800c..ac563a70c023 100644
--- a/drivers/pci/pwrctl/Makefile
+++ b/drivers/pci/pwrctl/Makefile
@@ -4,3 +4,4 @@ obj-$(CONFIG_PCI_PWRCTL)		+= pci-pwrctl-core.o
 pci-pwrctl-core-y			:= core.o
 
 obj-$(CONFIG_PCI_PWRCTL_PWRSEQ)		+= pci-pwrctl-pwrseq.o
+obj-$(CONFIG_PCI_PWRCTL_QPS615)		+= pci-pwrctl-qps615.o
diff --git a/drivers/pci/pwrctl/pci-pwrctl-qps615.c b/drivers/pci/pwrctl/pci-pwrctl-qps615.c
new file mode 100644
index 000000000000..1f2caf5d7da2
--- /dev/null
+++ b/drivers/pci/pwrctl/pci-pwrctl-qps615.c
@@ -0,0 +1,278 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <linux/device.h>
+#include <linux/firmware.h>
+#include <linux/i2c.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/pci-pwrctl.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/string.h>
+#include <linux/types.h>
+
+#include "../pci.h"
+
+struct qcom_qps615_pwrctl_i2c_setting {
+	u32 slv_addr;
+	u32 reg_addr;
+	u32 val;
+};
+
+struct qcom_qps615_pwrctl_ctx {
+	struct i2c_adapter *adapter;
+	struct pci_pwrctl pwrctl;
+	struct device_link *link;
+	struct regulator *vdd;
+};
+
+/* write 32-bit value to 24 bit register */
+static int qps615_switch_i2c_write(struct qcom_qps615_pwrctl_ctx *ctx, u32 slv_addr, u32 reg_addr,
+				   u32 reg_val)
+{
+	struct i2c_msg msg;
+	u8 msg_buf[7];
+	int ret;
+
+	msg.addr = slv_addr;
+	msg.len = 7;
+	msg.flags = 0;
+
+	/* Big Endian for reg addr */
+	msg_buf[0] = (u8)(reg_addr >> 16);
+	msg_buf[1] = (u8)(reg_addr >> 8);
+	msg_buf[2] = (u8)reg_addr;
+
+	/* Little Endian for reg val */
+	msg_buf[3] = (u8)(reg_val);
+	msg_buf[4] = (u8)(reg_val >> 8);
+	msg_buf[5] = (u8)(reg_val >> 16);
+	msg_buf[6] = (u8)(reg_val >> 24);
+
+	msg.buf = msg_buf;
+	ret = i2c_transfer(ctx->adapter, &msg, 1);
+	return ret == 1 ? 0 : ret;
+}
+
+/* read 32 bit value from 24 bit reg addr */
+static int qps615_switch_i2c_read(struct qcom_qps615_pwrctl_ctx *ctx, u32 slv_addr, u32 reg_addr,
+				  u32 *reg_val)
+{
+	u8 wr_data[3], rd_data[4] = {0};
+	struct i2c_msg msg[2];
+	int ret;
+
+	msg[0].addr = slv_addr;
+	msg[0].len = 3;
+	msg[0].flags = 0;
+
+	/* Big Endian for reg addr */
+	wr_data[0] = (u8)(reg_addr >> 16);
+	wr_data[1] = (u8)(reg_addr >> 8);
+	wr_data[2] = (u8)reg_addr;
+
+	msg[0].buf = wr_data;
+
+	msg[1].addr = slv_addr;
+	msg[1].len = 4;
+	msg[1].flags = I2C_M_RD;
+
+	msg[1].buf = rd_data;
+
+	ret = i2c_transfer(ctx->adapter, &msg[0], 2);
+	if (ret != 2)
+		return ret;
+
+	*reg_val = (rd_data[3] << 24) | (rd_data[2] << 16) | (rd_data[1] << 8) | rd_data[0];
+
+	return 0;
+}
+
+static int qcom_qps615_pwrctl_init(struct qcom_qps615_pwrctl_ctx *ctx)
+{
+	struct device *dev = ctx->pwrctl.dev;
+	struct qcom_qps615_pwrctl_i2c_setting *set;
+	const struct firmware *fw;
+	const u8 *pos, *eof;
+	int ret;
+	u32 val;
+
+	ret = request_firmware(&fw, "qcom/qps615.bin", dev);
+	if (ret < 0) {
+		dev_err(dev, "firmware loading failed with ret %d\n", ret);
+		return ret;
+	}
+
+	if (!fw) {
+		ret = -EINVAL;
+		goto err;
+	}
+
+	pos = fw->data;
+	eof = fw->data + fw->size;
+
+	while (pos < (fw->data + fw->size)) {
+		set = (struct qcom_qps615_pwrctl_i2c_setting *)pos;
+
+		ret = qps615_switch_i2c_write(ctx, set->slv_addr, set->reg_addr, set->val);
+		if (ret) {
+			dev_err(dev,
+				"I2c write failed for slv addr:%x at addr%x with val %x ret %d\n",
+				set->slv_addr, set->reg_addr, set->val, ret);
+			goto err;
+		}
+
+		ret = qps615_switch_i2c_read(ctx,  set->slv_addr, set->reg_addr, &val);
+		if (ret) {
+			dev_err(dev, "I2c read failed for slv addr:%x at addr%x ret %d\n",
+				set->slv_addr, set->reg_addr, ret);
+			goto err;
+		}
+
+		if (set->val != val) {
+			dev_err(dev,
+				"I2c read's mismatch for slv:%x at addr%x exp%d got%d\n",
+				set->slv_addr, set->reg_addr, set->val, val);
+			goto err;
+		}
+		pos += sizeof(struct qcom_qps615_pwrctl_i2c_setting);
+	}
+
+err:
+	release_firmware(fw);
+
+	return ret;
+}
+
+static int qcom_qps615_power_on(struct qcom_qps615_pwrctl_ctx *ctx)
+{
+	int ret;
+
+	ret = regulator_enable(ctx->vdd);
+	if (ret) {
+		dev_err(ctx->pwrctl.dev, "cannot enable vdda regulator\n");
+		return ret;
+	}
+
+	ret = qcom_qps615_pwrctl_init(ctx);
+	if (ret)
+		regulator_disable(ctx->vdd);
+
+	return ret;
+}
+
+static int qcom_qps615_power_off(struct qcom_qps615_pwrctl_ctx *ctx)
+{
+	return regulator_disable(ctx->vdd);
+}
+
+static int qcom_qps615_pwrctl_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *node = pdev->dev.of_node;
+	struct qcom_qps615_pwrctl_ctx *ctx;
+	struct device_node *adapter_node;
+	struct pci_host_bridge *bridge;
+	struct i2c_adapter *adapter;
+	struct pci_bus *bus;
+
+	bus = pci_find_bus(of_get_pci_domain_nr(dev->parent->of_node), 0);
+	if (!bus)
+		return -ENODEV;
+
+	bridge = pci_find_host_bridge(bus);
+
+	ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return -ENOMEM;
+
+	adapter_node = of_parse_phandle(node, "switch-i2c-cntrl", 0);
+	if (adapter_node) {
+		adapter = of_get_i2c_adapter_by_node(adapter_node);
+		__free(adapter_node);
+		if (!adapter)
+			return dev_err_probe(dev, -EPROBE_DEFER,
+					     "failed to parse switch-i2c-cntrl\n");
+	}
+
+	ctx->pwrctl.dev = dev;
+	ctx->adapter = adapter;
+	ctx->vdd = devm_regulator_get(dev, "vdd");
+	if (IS_ERR(ctx->vdd))
+		return dev_err_probe(dev, PTR_ERR(ctx->vdd),
+				     "failed to get vdd regulator\n");
+
+	ctx->link = device_link_add(&bridge->dev, dev, DL_FLAG_AUTOREMOVE_CONSUMER);
+
+	platform_set_drvdata(pdev, ctx);
+
+	bridge->ops->stop_link(bus);
+	qcom_qps615_power_on(ctx);
+	bridge->ops->start_link(bus);
+
+	return devm_pci_pwrctl_device_set_ready(dev, &ctx->pwrctl);
+}
+
+static const struct of_device_id qcom_qps615_pwrctl_of_match[] = {
+	{
+		.compatible = "pci1179,0623",
+	},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, qcom_qps615_pwrctl_of_match);
+
+static int pci_pwrctl_suspend_noirq(struct device *dev)
+{
+	struct pci_bus *bus = pci_find_bus(of_get_pci_domain_nr(dev->parent->of_node), 0);
+	struct pci_host_bridge *bridge = pci_find_host_bridge(bus);
+	struct qcom_qps615_pwrctl_ctx *ctx = dev_get_drvdata(dev);
+
+	bridge->ops->stop_link(bus);
+	qcom_qps615_power_off(ctx);
+
+	return 0;
+}
+
+static int pci_pwrctl_resume_noirq(struct device *dev)
+{
+	struct pci_bus *bus = pci_find_bus(of_get_pci_domain_nr(dev->parent->of_node), 0);
+	struct pci_host_bridge *bridge = pci_find_host_bridge(bus);
+	struct qcom_qps615_pwrctl_ctx *ctx = dev_get_drvdata(dev);
+
+	qcom_qps615_power_on(ctx);
+	bridge->ops->start_link(bus);
+
+	return 0;
+}
+
+static void qcom_qps615_pwrctl_remove(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct qcom_qps615_pwrctl_ctx *ctx = dev_get_drvdata(dev);
+
+	device_link_del(ctx->link);
+	pci_pwrctl_suspend_noirq(dev);
+}
+
+static const struct dev_pm_ops pci_pwrctl_pm_ops = {
+	NOIRQ_SYSTEM_SLEEP_PM_OPS(pci_pwrctl_suspend_noirq, pci_pwrctl_resume_noirq)
+};
+
+static struct platform_driver qcom_qps615_pwrctl_driver = {
+	.driver = {
+		.name = "pwrctl-qps615",
+		.of_match_table = qcom_qps615_pwrctl_of_match,
+		.pm = &pci_pwrctl_pm_ops,
+	},
+	.probe = qcom_qps615_pwrctl_probe,
+	.remove_new = qcom_qps615_pwrctl_remove,
+};
+module_platform_driver(qcom_qps615_pwrctl_driver);
+
+MODULE_AUTHOR("Krishna chaitanya chundru <quic_krichai@xxxxxxxxxxx>");
+MODULE_DESCRIPTION("Qualcomm QPS615 power control driver");
+MODULE_LICENSE("GPL");

-- 
2.42.0





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux