On 26/06/2024 10:30, Alexandre Mergnat wrote:
>
>
> On 25/06/2024 15:44, Krzysztof Kozlowski wrote:
>> On 25/06/2024 11:23, Alexandre Mergnat wrote:
>>>
>>>
>>> On 21/06/2024 17:00, Krzysztof Kozlowski wrote:
>>>> On 19/06/2024 16:46, Alexandre Mergnat wrote:
>>>>> Add the audio codec sub-device. This sub-device is used to set the
>>>>> optional voltage values according to the hardware.
>>>>> The properties are:
>>>>> - Setup of microphone bias voltage.
>>>>> - Setup of the speaker pin pull-down.
>>>>>
>>>>> Also, add the audio power supply property which is dedicated for
>>>>> the audio codec sub-device.
>>>>>
>>>>> Signed-off-by: Alexandre Mergnat<amergnat@xxxxxxxxxxxx>
>>>>> ---
>>>>> .../devicetree/bindings/mfd/mediatek,mt6357.yaml | 33 ++++++++++++++++++++++
>>>>> 1 file changed, 33 insertions(+)
>>>>>
>>>>> diff --git a/Documentation/devicetree/bindings/mfd/mediatek,mt6357.yaml b/Documentation/devicetree/bindings/mfd/mediatek,mt6357.yaml
>>>>> index 37423c2e0fdf..d95307393e75 100644
>>>>> --- a/Documentation/devicetree/bindings/mfd/mediatek,mt6357.yaml
>>>>> +++ b/Documentation/devicetree/bindings/mfd/mediatek,mt6357.yaml
>>>>> @@ -37,6 +37,32 @@ properties:
>>>>> "#interrupt-cells":
>>>>> const: 2
>>>>>
>>>>> + vaud28-supply:
>>>>> + description: 2.8 volt supply phandle for the audio codec
>>>>> +
>>>>> + audio-codec:
>>>>> + type: object
>>>> Still not much improved. You do not have any resources there, so these
>>>> should go to the parent node.
>>>
>>> Hi Krzysztof,
>>>
>>> vaud28-supply seems to be a mistake that I forward port.
>>> In the V4, AFAII, your feedback [1] suggested me to move the vaud28-supply from the "audio-codec"
>>> sub-node to the parent node, which for me is the "pmic" (mfd), because the property is considered as
>>> power-supply.
>>>
>>> pwrap {
>>> pmic {
>>> ...
>>> audio-codec {
>>> ...
>>>
>>> Hardware side, vaud28-supply is the output of PMIC-regulator subsystem, and AVDD28 is the input of
>>> PMIC-audio-codec subsystem. Then:
>>> - The property name is wrong and must be change to AVDD28, which is a consumer (power input), not a
>>> power-supply. => description: 2.8 volt power input for microphones (AU_VIN0, AU_VIN1, AU_VIN2)
>>> - IMHO, move this property to the next parent (pwrap) isn't consistent. It should be moved back to
>>> Documentation/devicetree/bindings/mfd/mediatek,mt6357.yaml (Done in the V4) into audio-codec
>>> substystem, beside mediatek,micbias0-microvolt
>>
>> I don't understand why do we talk again about supply. My comment was not
>> under the supply.
>
> Because your word are:
> "
> And now you should see how odd it looks. Supplies are part of entire
> chip, not subblock, even if they supply dedicated domain within that chip.
>
> That's why I asked to put it in the parent node.
> "
>
> My bad, I forgot to link you the old message in my previous answer [1]
>
> [1] https://lore.kernel.org/all/6d21da37-8be7-467c-8878-d57af0b0201b@xxxxxxxxxx/#t
And you implemented this, so why do we talk again about it? It is
already solved, isn't it? Since previous version?
Best regards,
Krzysztof
