[PATCH] ARM: dts: qcom: motorola-falcon: add accelerometer, magnetometer

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add the accelerometer and magnetometer that are present on the Motorola
Moto G (2013) device.

Signed-off-by: Stanislav Jakubek <stano.jakubek@xxxxxxxxx>
---
 .../boot/dts/qcom/msm8226-motorola-falcon.dts | 53 +++++++++++++++++++
 1 file changed, 53 insertions(+)

diff --git a/arch/arm/boot/dts/qcom/msm8226-motorola-falcon.dts b/arch/arm/boot/dts/qcom/msm8226-motorola-falcon.dts
index 029e1b1659c9..5dbca83f2230 100644
--- a/arch/arm/boot/dts/qcom/msm8226-motorola-falcon.dts
+++ b/arch/arm/boot/dts/qcom/msm8226-motorola-falcon.dts
@@ -96,6 +96,35 @@ reserved@fb00000 {
 	};
 };
 
+&blsp1_i2c2 {
+	status = "okay";
+
+	magnetometer@c {
+		compatible = "asahi-kasei,ak8963";
+		reg = <0xc>;
+		interrupts-extended = <&tlmm 66 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&pm8226_l19>;
+		vid-supply = <&pm8226_lvs1>;
+		pinctrl-0 = <&mag_int_default &mag_reset_default>;
+		pinctrl-names = "default";
+	};
+
+	accelerometer@19 {
+		compatible = "st,lis3dh-accel";
+		reg = <0x19>;
+		interrupts-extended = <&tlmm 63 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l19>;
+		vddio-supply = <&pm8226_lvs1>;
+		pinctrl-0 = <&accel_int_default>;
+		pinctrl-names = "default";
+		mount-matrix = "0", "1", "0",
+			       "1", "0", "0",
+			       "0", "0", "-1";
+		st,drdy-int-pin = <1>;
+	};
+};
+
 &blsp1_i2c3 {
 	status = "okay";
 
@@ -321,6 +350,30 @@ &smbb {
 };
 
 &tlmm {
+	accel_int_default: accel-int-default-state {
+		pins = "gpio63";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-disable;
+	};
+
+	mag_int_default: mag-int-default-state {
+		pins = "gpio66";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-disable;
+	};
+
+	mag_reset_default: mag-reset-default-state {
+		pins = "gpio62";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+
 	reg_lcd_default: reg-lcd-default-state {
 		pins = "gpio31", "gpio33";
 		function = "gpio";
-- 
2.34.1





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux