On 6/1/24 7:15 AM, Siddharth Vadapalli wrote:
Enable PCIe0 instance of PCIe in Root Complex mode of operation with Lane 0
of the SERDES1 instance of SERDES. Also enable USB0 instance of USB to
interface with the Type-C port via the USB hub, by configuring the pin P05
of the GPIO expander on the EVM. Enable USB1 instance of USB in SuperSpeed
mode of operation with Lane 0 of the SERDES0 instance of SERDES.
Co-developed-by: Ravi Gunasekaran <r-gunasekaran@xxxxxx>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@xxxxxx>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@xxxxxx>
---
v3:
https://lore.kernel.org/r/20240524090514.152727-4-s-vadapalli@xxxxxx/
and
https://lore.kernel.org/r/20240524090514.152727-8-s-vadapalli@xxxxxx/
Changes since v3:
- Above patches have been squashed into this patch.
arch/arm64/boot/dts/ti/k3-j722s-evm.dts | 72 +++++++++++++++++++++++++
1 file changed, 72 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j722s-evm.dts b/arch/arm64/boot/dts/ti/k3-j722s-evm.dts
index bf3c246d13d1..3145e680e2d3 100644
--- a/arch/arm64/boot/dts/ti/k3-j722s-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j722s-evm.dts
@@ -9,7 +9,9 @@
/dts-v1/;
#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/phy/phy.h>
#include "k3-j722s.dtsi"
+#include "k3-serdes.h"
/ {
compatible = "ti,j722s-evm", "ti,j722s";
@@ -202,6 +204,12 @@ J722S_IOPAD(0x0130, PIN_OUTPUT, 0) /* (AG26) RGMII1_TXC */
J722S_IOPAD(0x012c, PIN_OUTPUT, 0) /* (AF25) RGMII1_TX_CTL */
>;
};
+
+ main_usb1_pins_default: main-usb1-default-pins {
+ pinctrl-single,pins = <
+ J722S_IOPAD(0x0258, PIN_INPUT, 0) /* (B27) USB1_DRVVBUS */
+ >;
+ };
};
&cpsw3g {
@@ -301,6 +309,13 @@ exp1: gpio@23 {
"PCIe0_1L_RC_RSTz", "PCIe0_1L_PRSNT#",
"ENET1_EXP_SPARE2", "ENET1_EXP_PWRDN",
"PD_I2ENET1_I2CMUX_SELC_IRQ", "ENET1_EXP_RESETZ";
+
+ p05-hog {
+ /* P05 - USB2.0_MUX_SEL */
+ gpio-hog;
+ gpios = <5 GPIO_ACTIVE_HIGH>;
+ output-high;
+ };
};
};
@@ -384,3 +399,60 @@ &sdhci1 {
status = "okay";
bootph-all;
};
+
+&serdes_ln_ctrl {
+ idle-states = <J722S_SERDES0_LANE0_USB>,
+ <J722S_SERDES1_LANE0_PCIE0_LANE0>;
+};
+
+&serdes0 {
+ status = "okay";
+ serdes0_usb_link: phy@0 {
+ reg = <0>;
+ cdns,num-lanes = <1>;
+ #phy-cells = <0>;
+ cdns,phy-type = <PHY_TYPE_USB3>;
+ resets = <&serdes_wiz0 1>;
+ };
+};
+
+&serdes1 {
+ serdes1_pcie_link: phy@0 {
+ reg = <0>;
+ cdns,num-lanes = <1>;
+ #phy-cells = <0>;
+ cdns,phy-type = <PHY_TYPE_PCIE>;
+ resets = <&serdes_wiz1 1>;
+ };
+};
+
+&pcie0_rc {
+ status = "okay";
As much as I like these at the top, the new format rules seems to
suggest "status" properties should go at the bottom of the node.
Andrew
+ reset-gpios = <&exp1 18 GPIO_ACTIVE_HIGH>;
+ phys = <&serdes1_pcie_link>;
+ phy-names = "pcie-phy";
+};
+
+&usbss0 {
+ ti,vbus-divider;
+ status = "okay";
+};
+
+&usb0 {
+ dr_mode = "otg";
+ usb-role-switch;
+};
+
+&usbss1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_usb1_pins_default>;
+ ti,vbus-divider;
+ status = "okay";
+};
+
+&usb1 {
+ dr_mode = "host";
+ maximum-speed = "super-speed";
+ phys = <&serdes0_usb_link>;
+ phy-names = "cdns3,usb3-phy";
+};
