The GPIO expander on the EVM allows the USB selection for Type-C port to either USB0 or USB1 via USB hub. By default, let the Type-C port select USB0 via the GPIO expander port P05. Enable super-speed on USB1 by updating SerDes0 lane configuration. Signed-off-by: Ravi Gunasekaran <r-gunasekaran@xxxxxx> --- Changes since v1: ---------------- * Removed USB aliases, line-name property for p05 GPIO hog * Included k3-j722s-main.dtsi v1: https://lore.kernel.org/all/20240429120932.11456-1-r-gunasekaran@xxxxxx/ arch/arm64/boot/dts/ti/k3-j722s-evm.dts | 55 +++++++++++++++++++++++++ arch/arm64/boot/dts/ti/k3-j722s.dtsi | 5 +++ arch/arm64/boot/dts/ti/k3-serdes.h | 7 ++++ 3 files changed, 67 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-j722s-evm.dts b/arch/arm64/boot/dts/ti/k3-j722s-evm.dts index bf3c246d13d1..531912be97c9 100644 --- a/arch/arm64/boot/dts/ti/k3-j722s-evm.dts +++ b/arch/arm64/boot/dts/ti/k3-j722s-evm.dts @@ -9,7 +9,9 @@ /dts-v1/; #include <dt-bindings/net/ti-dp83867.h> +#include <dt-bindings/phy/phy.h> #include "k3-j722s.dtsi" +#include "k3-serdes.h" / { compatible = "ti,j722s-evm", "ti,j722s"; @@ -202,6 +204,12 @@ J722S_IOPAD(0x012c, PIN_OUTPUT, 0) /* (AF25) RGMII1_TX_CTL */ >; }; + + main_usb1_pins_default: main-usb1-default-pins { + pinctrl-single,pins = < + J722S_IOPAD(0x0258, PIN_INPUT, 0) /* (B27) USB1_DRVVBUS */ + >; + }; }; &cpsw3g { @@ -301,6 +309,13 @@ "PCIe0_1L_RC_RSTz", "PCIe0_1L_PRSNT#", "ENET1_EXP_SPARE2", "ENET1_EXP_PWRDN", "PD_I2ENET1_I2CMUX_SELC_IRQ", "ENET1_EXP_RESETZ"; + + p05-hog { + /* P05 - USB2.0_MUX_SEL */ + gpio-hog; + gpios = <5 GPIO_ACTIVE_LOW>; + output-high; + }; }; }; @@ -384,3 +399,43 @@ status = "okay"; bootph-all; }; + +&serdes0_ln_ctrl { + idle-states = <J722S_SERDES0_LANE0_USB>, + <J722S_SERDES1_LANE0_PCIE0_LANE0>; +}; + +&serdes0 { + status = "okay"; + serdes0_usb_link: phy@0 { + reg = <0>; + cdns,num-lanes = <1>; + #phy-cells = <0>; + cdns,phy-type = <PHY_TYPE_USB3>; + resets = <&serdes_wiz0 1>; + }; +}; + +&usbss0 { + ti,vbus-divider; + status = "okay"; +}; + +&usb0 { + dr_mode = "otg"; + usb-role-switch; +}; + +&usbss1 { + pinctrl-names = "default"; + pinctrl-0 = <&main_usb1_pins_default>; + ti,vbus-divider; + status = "okay"; +}; + +&usb1 { + dr_mode = "host"; + maximum-speed = "super-speed"; + phys = <&serdes0_usb_link>; + phy-names = "cdns3,usb3-phy"; +}; diff --git a/arch/arm64/boot/dts/ti/k3-j722s.dtsi b/arch/arm64/boot/dts/ti/k3-j722s.dtsi index c75744edb143..61b64fae1bf4 100644 --- a/arch/arm64/boot/dts/ti/k3-j722s.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j722s.dtsi @@ -87,3 +87,8 @@ reg = <0x00 0x70000000 0x00 0x40000>; ranges = <0x00 0x00 0x70000000 0x40000>; }; + +/* Include bus peripherals that are additionally + * present in J722S + */ + #include "k3-j722s-main.dtsi" diff --git a/arch/arm64/boot/dts/ti/k3-serdes.h b/arch/arm64/boot/dts/ti/k3-serdes.h index a011ad893b44..9082abeddcb1 100644 --- a/arch/arm64/boot/dts/ti/k3-serdes.h +++ b/arch/arm64/boot/dts/ti/k3-serdes.h @@ -201,4 +201,11 @@ #define J784S4_SERDES4_LANE3_USB 0x2 #define J784S4_SERDES4_LANE3_IP4_UNUSED 0x3 +/* J722S */ +#define J722S_SERDES0_LANE0_USB 0x0 +#define J722S_SERDES0_LANE0_QSGMII_LANE2 0x1 + +#define J722S_SERDES1_LANE0_PCIE0_LANE0 0x0 +#define J722S_SERDES1_LANE0_QSGMII_LANE1 0x1 + #endif /* DTS_ARM64_TI_K3_SERDES_H */ -- 2.17.1
