On Wed, May 01, 2024 at 06:05:28PM GMT, Conor Dooley wrote: > On Wed, May 01, 2024 at 08:28:47AM +0800, Inochi Amaoto wrote: > > On Tue, Apr 30, 2024 at 06:09:20PM GMT, Conor Dooley wrote: > > > On Mon, Apr 29, 2024 at 08:31:11AM +0800, Inochi Amaoto wrote: > > > > The USB phy of Sophgo CV18XX series SoC needs to sense a pin called > > > > "VBUS_DET" to get the right operation mode. If this pin is not > > > > connected, it only supports setting the mode manually. > > > > > > > > Add USB phy bindings for Sophgo CV18XX/SG200X series SoC. > > > > > > > > Signed-off-by: Inochi Amaoto <inochiama@xxxxxxxxxxx> > > > > --- > > > > .../bindings/phy/sophgo,cv1800-usb-phy.yaml | 68 +++++++++++++++++++ > > > > 1 file changed, 68 insertions(+) > > > > create mode 100644 Documentation/devicetree/bindings/phy/sophgo,cv1800-usb-phy.yaml > > > > > > > > diff --git a/Documentation/devicetree/bindings/phy/sophgo,cv1800-usb-phy.yaml b/Documentation/devicetree/bindings/phy/sophgo,cv1800-usb-phy.yaml > > > > new file mode 100644 > > > > index 000000000000..7e3382c18d44 > > > > --- /dev/null > > > > +++ b/Documentation/devicetree/bindings/phy/sophgo,cv1800-usb-phy.yaml > > > > @@ -0,0 +1,68 @@ > > > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > > > +%YAML 1.2 > > > > +--- > > > > +$id: http://devicetree.org/schemas/phy/sophgo,cv1800-usb-phy.yaml# > > > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > > > + > > > > +title: Sophgo CV18XX/SG200X USB 2.0 PHY > > > > + > > > > +maintainers: > > > > + - Inochi Amaoto <inochiama@xxxxxxxxxxx> > > > > + > > > > +properties: > > > > + compatible: > > > > + const: sophgo,cv1800-usb-phy > > > > + > > > > + reg: > > > > + maxItems: 1 > > > > + > > > > + "#phy-cells": > > > > + const: 0 > > > > + > > > > + clocks: > > > > + items: > > > > + - description: PHY clock > > > > + - description: PHY app clock > > > > + - description: PHY stb clock > > > > + - description: PHY lpm clock > > > > + > > > > + clock-names: > > > > + items: > > > > + - const: phy > > > > + - const: app > > > > + - const: stb > > > > + - const: lpm > > > > + > > > > + vbus_det-gpios: > > > > > > "vbus_det-gpios" isn't a common property AFAICT, why does it not get a > > > vendor prefix when the other gpios property does? > > > > > > > I have seen other binding (such as sunxi phy) uses this property without > > vendor prefix. So I think it is a common property and don't add perfix > > for it. But it is OK for me add the vendor prefix, thanks. > > I asked yesterday and Krzysztof said: > "gpios just like supplies - no prefixes, I think." Thanks for your explanation. If I do not understand wrong, you mean it does not need to add vender prefix? > The other phy used a different property (they're not identical), I did > check that yesterday. > Yes, it is not total identical. But they do look similar. > > > > > > + description: GPIO to the USB OTG VBUS detect pin. This should not be > > > > + defined if vbus_det pin and switch pin are connected, which may > > > > + break the VBUS detection. > > > > + maxItems: 1 > > > > + > > > > + sophgo,switch-gpios: > > > > + description: GPIO array for the phy to control connected switch. For > > > > + host mode, the driver will set these GPIOs to low one by one. For > > > > + device mode, the driver will set these GPIOs to high in reverse > > > > + order. > > > > + maxItems: 2 > > > > > > You're still missing the itemised description of what each of the gpios > > > here are - how would I know which order to put the GPIOs in? > > > > > > Cheers, > > > Conor. > > > > In most case, the order depends on hardware design. But following the > > guide sophgo provides, it does have an common order. Is it good to add > > this description as a reference guide? If so, I will add it. > > If we can say "gpio 1 connects to xyz on the switch" & "gpio 2 connects > to tuv" then it'll be easier to understand how to write the node. > Good, I will add description of reference design for these gpios. > > > > Regards, > > Inochi > > > > > > > > > + > > > > +required: > > > > + - compatible > > > > + - "#phy-cells" > > > > + - clocks > > > > + - clock-names > > > > + > > > > +additionalProperties: false > > > > + > > > > +examples: > > > > + - | > > > > + phy@48 { > > > > + compatible = "sophgo,cv1800-usb-phy"; > > > > + reg = <0x48 0x4>; > > > > + #phy-cells = <0>; > > > > + clocks = <&clk 92>, <&clk 93>, > > > > + <&clk 94>, <&clk 95>; > > > > + clock-names = "phy", "app", "stb", "lpm"; > > > > + }; > > > > + > > > > +... > > > > -- > > > > 2.44.0 > > > > > > > >
