On Wed, 24 Apr 2024 23:09:45 +1200 Ryan Walklin <ryan@xxxxxxxxxxxxx> wrote: Hi Ryan (and Chris), many thanks for the changes, that looks really close now. Only a few smaller comments this time. > The base model RG35XX (2024) is a handheld gaming device based on an Allwinner H700 chip. > > The H700 is a H616 variant (4x ARM Cortex-A53 cores @ 1.5Ghz with Mali G31 GPU) which exposes RGB LCD and NMI pins. > > Device features: > - Allwinner H700 @ 1.5GHz > - 1GB LPDDR4 DRAM > - X-Powers AXP717 PMIC > - 3.5" 640x480 RGB LCD > - Two microSD slots > - Mini-HDMI out > - GPIO keypad > - 3.5mm headphone jack > - USB-C charging port > > Enabled in this DTS: > - AXP717 PMIC with regulators (interrupt controller TBC/TBD) > - Power LED (charge LED on device controlled directly by PMIC) > - Serial UART (accessible from PIN headers on the board) > - MMC slots > > Signed-off-by: Ryan Walklin <ryan@xxxxxxxxxxxxx> > --- > Changelog v1..v2: > - Update copyright > - Spaces -> Tabs > - Add cpufreq support > - Remove MMC aliases > - Fix GPIO button and regulator node names > - Note unused AXP717 regulators > - Update regulators for SD slots > - Remove unused I2C3 device > - Update NMI interrupt controller for AXP717, requires H616 support patch in dt-next [1] > - Add chassis-type > - Address USB EHCI/OHCI0 correctly and add usb vbus supply > - Add PIO vcc-pg-supply > - Correct boost regulator voltage and name > > Changelog v2..v3: > - Remove cpufreq support (patch still pending for 6.10, will followup once opp table merged) > - Add dtb to Makefile > - Remove unnecessary duplicated PLL regulator > - Remove unimplemented/not-present drive-vbus feature from AXP717 > - Rename CLDO3 to "vcc-io", inferring function from board testing by Chris Morgan > - Correct MMC1 vmmc-supply to CLDO3 and MMC2 to CLDO4 > - Reduce DCDC1 "vdd-cpu" supply voltage range to 0.9v-1.1v to match lowest OPP voltage > - Identify DCDC2 as GPU supply - rename to "vdd-gpu-sys", remove always-on and used fixed 0.94v voltage > - Fix indentation > - Correct boot/always-on states and voltages for various regulators from vendor BSP > - Change USB-OTG mode to "peripheral" and correct comment > - Correct and add remaining PIO supplies > - Move volume key GPIOs to separate block to allow key repeat > - Alphabetically orrder gamepad GPIOs > - Move changelog and links below fold-line > - Remove USB 3.3v VCC-USB and VCC-SD2 regulators pending further hardware investigation (to be submitted as subsequent patch) > - Constrain boost regulator voltage to 5.0v to 5.2v to capture default voltage of 5.126v > > [1]: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git/commit/?h=dt/next&id=d47bca77bf3ab475c33b3929c33c80aeb49df35c > > --- > arch/arm64/boot/dts/allwinner/Makefile | 1 + > .../sun50i-h700-anbernic-rg35xx-2024.dts | 347 ++++++++++++++++++ > 2 files changed, 348 insertions(+) > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile > index 21149b346a60..6f997157968e 100644 > --- a/arch/arm64/boot/dts/allwinner/Makefile > +++ b/arch/arm64/boot/dts/allwinner/Makefile > @@ -47,3 +47,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-longanpi-3h.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero2w.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-transpeed-8k618-t.dtb > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-2024.dtb > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts > new file mode 100644 > index 000000000000..3b53485019f1 > --- /dev/null > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts > @@ -0,0 +1,347 @@ > +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +/* > + * Copyright (C) 2024 Ryan Walklin <ryan@xxxxxxxxxxxxx>. > + */ > + > +/dts-v1/; > + > +#include "sun50i-h616.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/linux-event-codes.h> > +#include <dt-bindings/interrupt-controller/arm-gic.h> > +#include <dt-bindings/leds/common.h> > + > +/ { > + model = "Anbernic RG35XX 2024"; > + chassis-type = "handset"; > + compatible = "anbernic,rg35xx-2024", "allwinner,sun50i-h700"; > + > + aliases { > + serial0 = &uart0; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + led-0 { > + function = LED_FUNCTION_POWER; > + color = <LED_COLOR_ID_GREEN>; > + gpios = <&pio 8 12 GPIO_ACTIVE_HIGH>; /* PI12 */ > + default-state = "on"; > + }; > + }; > + > + gpio_keys_gamepad: gpio-keys-gamepad { > + compatible = "gpio-keys"; > + > + button-a { > + label = "Action-Pad A"; > + gpios = <&pio 0 0 GPIO_ACTIVE_LOW>; /* PA0 */ > + linux,input-type = <EV_KEY>; > + linux,code = <BTN_EAST>; > + }; > + > + button-b { > + label = "Action-Pad B"; > + gpios = <&pio 0 1 GPIO_ACTIVE_LOW>; /* PA1 */ > + linux,input-type = <EV_KEY>; > + linux,code = <BTN_SOUTH>; > + }; > + > + button-down { > + label = "D-Pad Down"; > + gpios = <&pio 4 0 GPIO_ACTIVE_LOW>; /* PE0 */ > + linux,input-type = <EV_KEY>; > + linux,code = <BTN_DPAD_DOWN>; > + }; > + > + button-l1 { > + label = "Key L1"; > + gpios = <&pio 0 10 GPIO_ACTIVE_LOW>; /* PA10 */ > + linux,input-type = <EV_KEY>; > + linux,code = <BTN_TL>; > + }; > + > + button-l2 { > + label = "Key L2"; > + gpios = <&pio 0 11 GPIO_ACTIVE_LOW>; /* PA11 */ > + linux,input-type = <EV_KEY>; > + linux,code = <BTN_TL2>; > + }; > + > + button-left { > + label = "D-Pad left"; > + gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */ > + linux,input-type = <EV_KEY>; > + linux,code = <BTN_DPAD_LEFT>; > + }; > + > + button-menu { > + label = "Key Menu"; > + gpios = <&pio 4 3 GPIO_ACTIVE_LOW>; /* PE3 */ > + linux,input-type = <EV_KEY>; > + linux,code = <BTN_MODE>; > + }; > + > + button-r1 { > + label = "Key R1"; > + gpios = <&pio 0 12 GPIO_ACTIVE_LOW>; /* PA12 */ > + linux,input-type = <EV_KEY>; > + linux,code = <BTN_TR>; > + }; > + > + button-r2 { > + label = "Key R2"; > + gpios = <&pio 0 7 GPIO_ACTIVE_LOW>; /* PA7 */ > + linux,input-type = <EV_KEY>; > + linux,code = <BTN_TR2>; > + }; > + > + button-right { > + label = "D-Pad Right"; > + gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */ > + linux,input-type = <EV_KEY>; > + linux,code = <BTN_DPAD_RIGHT>; > + }; > + > + button-select { > + label = "Key Select"; > + gpios = <&pio 0 5 GPIO_ACTIVE_LOW>; /* PA5 */ > + linux,input-type = <EV_KEY>; > + linux,code = <BTN_SELECT>; > + }; > + button-start { > + label = "Key Start"; > + gpios = <&pio 0 4 GPIO_ACTIVE_LOW>; /* PA4 */ > + linux,input-type = <EV_KEY>; > + linux,code = <BTN_START>; > + }; > + > + button-up { > + label = "D-Pad Up"; > + gpios = <&pio 0 6 GPIO_ACTIVE_LOW>; /* PA6 */ > + linux,input-type = <EV_KEY>; > + linux,code = <BTN_DPAD_UP>; > + }; > + > + button-x { > + label = "Action-Pad X"; > + gpios = <&pio 0 3 GPIO_ACTIVE_LOW>; /* PA3 */ > + linux,input-type = <EV_KEY>; > + linux,code = <BTN_NORTH>; > + }; > + > + button-y { > + label = "Action Pad Y"; > + gpios = <&pio 0 2 GPIO_ACTIVE_LOW>; /* PA2 */ > + linux,input-type = <EV_KEY>; > + linux,code = <BTN_WEST>; > + }; > + }; > + > + gpio-keys-volume { > + compatible = "gpio-keys"; > + autorepeat; > + > + button-vol-up { > + label = "Key Volume Up"; > + gpios = <&pio 4 1 GPIO_ACTIVE_LOW>; /* PE1 */ > + linux,input-type = <EV_KEY>; > + linux,code = <KEY_VOLUMEUP>; > + }; > + > + button-vol-down { > + label = "Key Volume Down"; > + gpios = <&pio 4 2 GPIO_ACTIVE_LOW>; /* PE2 */ > + linux,input-type = <EV_KEY>; > + linux,code = <KEY_VOLUMEDOWN>; > + }; > + }; > + > + reg_vcc5v: regulator-vcc5v { /* USB-C power input */ > + compatible = "regulator-fixed"; > + regulator-name = "vcc-5v"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + }; > +}; > + > +&cpu0 { > + cpu-supply = <®_dcdc1>; > +}; > + > +&mmc0 { > + vmmc-supply = <®_cldo3>; > + disable-wp; > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ > + bus-width = <4>; > + status = "okay"; > +}; > + > +&mmc2 { > + vmmc-supply = <®_cldo4>; > + vqmmc-supply = <®_aldo1>; This is now fixed to 1.8V, which doesn't look right. Either it's not the right regulator, or you should extend its range to cover 3.3V as well. > + cd-gpios = <&pio 4 22 GPIO_ACTIVE_LOW>; /* PE22 */ > + bus-width = <4>; > + status = "okay"; > +}; > + > +&ohci0 { > + status = "okay"; > +}; > + > +&ehci0 { > + status = "okay"; > +}; > + > +&r_rsb { > + status = "okay"; This is indented with spaces, not a tab. > + > + axp717: pmic@3a3 { > + compatible = "x-powers,axp717"; > + reg = <0x3a3>; > + interrupt-controller; > + #interrupt-cells = <1>; > + interrupt-parent = <&nmi_intc>; > + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; > + > + vin1-supply = <®_vcc5v>; > + vin2-supply = <®_vcc5v>; > + vin3-supply = <®_vcc5v>; > + vin4-supply = <®_vcc5v>; > + > + regulators { > + reg_dcdc1: dcdc1 { > + regulator-always-on; > + regulator-boot-on; boot-on doesn't make much sense here: that allows it to be turned off, which we don't want. Also the binding documentation in regulator.yaml says that it's only intended "where software cannot read the state of the regulator", which is not true here. regulator-always-on is all we need - technically speaking not even that, since cpu0 is a consumer, but we need to play safe here. > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <1100000>; > + regulator-name = "vdd-cpu"; > + }; > + > + reg_dcdc2: dcdc2 { > + regulator-always-on; > + regulator-min-microvolt = <940000>; > + regulator-max-microvolt = <940000>; > + regulator-name = "vdd-gpu-sys"; > + }; > + > + reg_dcdc3: dcdc3 { > + regulator-always-on; > + regulator-boot-on; Same here, please remove that last line. We must not turn that off, and the state is readable, so it's not needed. We need always-on here, since it has no consumer. > + regulator-min-microvolt = <1100000>; > + regulator-max-microvolt = <1100000>; > + regulator-name = "vdd-dram"; > + }; > + > + reg_aldo1: aldo1 { /* SDC2 */ > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc-sd2"; > + }; > + > + reg_aldo2: aldo2 { > + /* unused */ > + }; > + > + reg_aldo3: aldo3 { > + regulator-always-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "axp717-aldo3"; So do we know for sure that's critical? And do we have any clue what this supplies? There is AVCC, VCC_HDMI, VCC_TV, VCC_RTC, all at 1.8V. The middle two are not critical. > + }; > + > + reg_aldo4: aldo4 { /* 5096000.codec */ > + regulator-always-on; Is that necessary? What happens if that is turned off? Looks like only the WiFi and potentially audio is affected? I think it can go then, also pg-supply would reference it, so it would effectively be enabled anyways. > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc-pg"; > + }; > + > + reg_bldo1: bldo1 { > + /* unused */ > + }; > + > + reg_bldo2: bldo2 { > + regulator-always-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc-pll"; > + }; > + > + reg_bldo3: bldo3 { > + /* unused */ > + }; > + > + reg_bldo4: bldo4 { > + /* unused */ > + }; > + > + reg_cldo1: cldo1 { /* 5096000.codec */ > + /* unused */ > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; Looks a bit odd to have an "unused" comment, but also a voltage range specified. Judging from the comment this might be supplying some audio circuitry, which we don't need at the moment? The rest looks fine to me. Cheers, Andre > + regulator-name = "axp717-cldo1"; > + }; > + > + reg_cldo2: cldo2 { > + /* unused */ > + > + }; > + > + reg_cldo3: cldo3 { > + regulator-always-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-io"; > + }; > + > + reg_cldo4: cldo4 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-wifi"; > + }; > + > + reg_boost: boost { > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5200000>; > + regulator-name = "boost"; > + }; > + > + reg_cpusldo: cpusldo { > + /* unused */ > + }; > + }; > + }; > +}; > + > +&uart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_ph_pins>; > + status = "okay"; > +}; > + > +&pio { > + vcc-pa-supply = <®_cldo3>; > + vcc-pc-supply = <®_cldo3>; > + vcc-pe-supply = <®_cldo3>; > + vcc-pf-supply = <®_cldo3>; > + vcc-pg-supply = <®_aldo4>; > + vcc-ph-supply = <®_cldo3>; > + vcc-pi-supply = <®_cldo3>; > +}; > + > +/* the AXP717 has USB type-C role switch functionality, not yet described by the binding */ > +&usbotg { > + dr_mode = "peripheral"; /* USB type-C receptable */ > + status = "okay"; > +}; > + > +&usbphy { > + status = "okay"; > +};
