The base model RG35XX (2024) is a handheld gaming device based on an Allwinner H700 chip. The H700 is a H616 variant (4x ARM Cortex-A53 cores @ 1.5Ghz with Mali G31 GPU) which exposes RGB LCD and NMI pins. Device features: - Allwinner H700 @ 1.5GHz - 1GB LPDDR4 DRAM - X-Powers AXP717 PMIC - 3.5" 640x480 RGB LCD - Two microSD slots - Mini-HDMI out - GPIO keypad - 3.5mm headphone jack - USB-C charging port Enabled in this DTS: - AXP717 PMIC with regulators (interrupt controller TBC/TBD) - Power LED (charge LED on device controlled directly by PMIC) - Serial UART (accessible from PIN headers on the board) - MMC slots Signed-off-by: Ryan Walklin <ryan@xxxxxxxxxxxxx> --- Changelog v1..v2: - Update copyright - Spaces -> Tabs - Add cpufreq support - Remove MMC aliases - Fix GPIO button and regulator node names - Note unused AXP717 regulators - Update regulators for SD slots - Remove unused I2C3 device - Update NMI interrupt controller for AXP717, requires H616 support patch in dt-next [1] - Add chassis-type - Address USB EHCI/OHCI0 correctly and add usb vbus supply - Add PIO vcc-pg-supply - Correct boost regulator voltage and name Changelog v2..v3: - Remove cpufreq support (patch still pending for 6.10, will followup once opp table merged) - Add dtb to Makefile - Remove unnecessary duplicated PLL regulator - Remove unimplemented/not-present drive-vbus feature from AXP717 - Rename CLDO3 to "vcc-io", inferring function from board testing by Chris Morgan - Correct MMC1 vmmc-supply to CLDO3 and MMC2 to CLDO4 - Reduce DCDC1 "vdd-cpu" supply voltage range to 0.9v-1.1v to match lowest OPP voltage - Identify DCDC2 as GPU supply - rename to "vdd-gpu-sys", remove always-on and used fixed 0.94v voltage - Fix indentation - Correct boot/always-on states and voltages for various regulators from vendor BSP - Change USB-OTG mode to "peripheral" and correct comment - Correct and add remaining PIO supplies - Move volume key GPIOs to separate block to allow key repeat - Alphabetically orrder gamepad GPIOs - Move changelog and links below fold-line - Remove USB 3.3v VCC-USB and VCC-SD2 regulators pending further hardware investigation (to be submitted as subsequent patch) - Constrain boost regulator voltage to 5.0v to 5.2v to capture default voltage of 5.126v [1]: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git/commit/?h=dt/next&id=d47bca77bf3ab475c33b3929c33c80aeb49df35c --- arch/arm64/boot/dts/allwinner/Makefile | 1 + .../sun50i-h700-anbernic-rg35xx-2024.dts | 347 ++++++++++++++++++ 2 files changed, 348 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile index 21149b346a60..6f997157968e 100644 --- a/arch/arm64/boot/dts/allwinner/Makefile +++ b/arch/arm64/boot/dts/allwinner/Makefile @@ -47,3 +47,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-longanpi-3h.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero2w.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-transpeed-8k618-t.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-2024.dtb diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts new file mode 100644 index 000000000000..3b53485019f1 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts @@ -0,0 +1,347 @@ +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +/* + * Copyright (C) 2024 Ryan Walklin <ryan@xxxxxxxxxxxxx>. + */ + +/dts-v1/; + +#include "sun50i-h616.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/linux-event-codes.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/leds/common.h> + +/ { + model = "Anbernic RG35XX 2024"; + chassis-type = "handset"; + compatible = "anbernic,rg35xx-2024", "allwinner,sun50i-h700"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + led-0 { + function = LED_FUNCTION_POWER; + color = <LED_COLOR_ID_GREEN>; + gpios = <&pio 8 12 GPIO_ACTIVE_HIGH>; /* PI12 */ + default-state = "on"; + }; + }; + + gpio_keys_gamepad: gpio-keys-gamepad { + compatible = "gpio-keys"; + + button-a { + label = "Action-Pad A"; + gpios = <&pio 0 0 GPIO_ACTIVE_LOW>; /* PA0 */ + linux,input-type = <EV_KEY>; + linux,code = <BTN_EAST>; + }; + + button-b { + label = "Action-Pad B"; + gpios = <&pio 0 1 GPIO_ACTIVE_LOW>; /* PA1 */ + linux,input-type = <EV_KEY>; + linux,code = <BTN_SOUTH>; + }; + + button-down { + label = "D-Pad Down"; + gpios = <&pio 4 0 GPIO_ACTIVE_LOW>; /* PE0 */ + linux,input-type = <EV_KEY>; + linux,code = <BTN_DPAD_DOWN>; + }; + + button-l1 { + label = "Key L1"; + gpios = <&pio 0 10 GPIO_ACTIVE_LOW>; /* PA10 */ + linux,input-type = <EV_KEY>; + linux,code = <BTN_TL>; + }; + + button-l2 { + label = "Key L2"; + gpios = <&pio 0 11 GPIO_ACTIVE_LOW>; /* PA11 */ + linux,input-type = <EV_KEY>; + linux,code = <BTN_TL2>; + }; + + button-left { + label = "D-Pad left"; + gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */ + linux,input-type = <EV_KEY>; + linux,code = <BTN_DPAD_LEFT>; + }; + + button-menu { + label = "Key Menu"; + gpios = <&pio 4 3 GPIO_ACTIVE_LOW>; /* PE3 */ + linux,input-type = <EV_KEY>; + linux,code = <BTN_MODE>; + }; + + button-r1 { + label = "Key R1"; + gpios = <&pio 0 12 GPIO_ACTIVE_LOW>; /* PA12 */ + linux,input-type = <EV_KEY>; + linux,code = <BTN_TR>; + }; + + button-r2 { + label = "Key R2"; + gpios = <&pio 0 7 GPIO_ACTIVE_LOW>; /* PA7 */ + linux,input-type = <EV_KEY>; + linux,code = <BTN_TR2>; + }; + + button-right { + label = "D-Pad Right"; + gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */ + linux,input-type = <EV_KEY>; + linux,code = <BTN_DPAD_RIGHT>; + }; + + button-select { + label = "Key Select"; + gpios = <&pio 0 5 GPIO_ACTIVE_LOW>; /* PA5 */ + linux,input-type = <EV_KEY>; + linux,code = <BTN_SELECT>; + }; + button-start { + label = "Key Start"; + gpios = <&pio 0 4 GPIO_ACTIVE_LOW>; /* PA4 */ + linux,input-type = <EV_KEY>; + linux,code = <BTN_START>; + }; + + button-up { + label = "D-Pad Up"; + gpios = <&pio 0 6 GPIO_ACTIVE_LOW>; /* PA6 */ + linux,input-type = <EV_KEY>; + linux,code = <BTN_DPAD_UP>; + }; + + button-x { + label = "Action-Pad X"; + gpios = <&pio 0 3 GPIO_ACTIVE_LOW>; /* PA3 */ + linux,input-type = <EV_KEY>; + linux,code = <BTN_NORTH>; + }; + + button-y { + label = "Action Pad Y"; + gpios = <&pio 0 2 GPIO_ACTIVE_LOW>; /* PA2 */ + linux,input-type = <EV_KEY>; + linux,code = <BTN_WEST>; + }; + }; + + gpio-keys-volume { + compatible = "gpio-keys"; + autorepeat; + + button-vol-up { + label = "Key Volume Up"; + gpios = <&pio 4 1 GPIO_ACTIVE_LOW>; /* PE1 */ + linux,input-type = <EV_KEY>; + linux,code = <KEY_VOLUMEUP>; + }; + + button-vol-down { + label = "Key Volume Down"; + gpios = <&pio 4 2 GPIO_ACTIVE_LOW>; /* PE2 */ + linux,input-type = <EV_KEY>; + linux,code = <KEY_VOLUMEDOWN>; + }; + }; + + reg_vcc5v: regulator-vcc5v { /* USB-C power input */ + compatible = "regulator-fixed"; + regulator-name = "vcc-5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; +}; + +&cpu0 { + cpu-supply = <®_dcdc1>; +}; + +&mmc0 { + vmmc-supply = <®_cldo3>; + disable-wp; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + bus-width = <4>; + status = "okay"; +}; + +&mmc2 { + vmmc-supply = <®_cldo4>; + vqmmc-supply = <®_aldo1>; + cd-gpios = <&pio 4 22 GPIO_ACTIVE_LOW>; /* PE22 */ + bus-width = <4>; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&r_rsb { + status = "okay"; + + axp717: pmic@3a3 { + compatible = "x-powers,axp717"; + reg = <0x3a3>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + + vin1-supply = <®_vcc5v>; + vin2-supply = <®_vcc5v>; + vin3-supply = <®_vcc5v>; + vin4-supply = <®_vcc5v>; + + regulators { + reg_dcdc1: dcdc1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpu"; + }; + + reg_dcdc2: dcdc2 { + regulator-always-on; + regulator-min-microvolt = <940000>; + regulator-max-microvolt = <940000>; + regulator-name = "vdd-gpu-sys"; + }; + + reg_dcdc3: dcdc3 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-dram"; + }; + + reg_aldo1: aldo1 { /* SDC2 */ + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-sd2"; + }; + + reg_aldo2: aldo2 { + /* unused */ + }; + + reg_aldo3: aldo3 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "axp717-aldo3"; + }; + + reg_aldo4: aldo4 { /* 5096000.codec */ + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-pg"; + }; + + reg_bldo1: bldo1 { + /* unused */ + }; + + reg_bldo2: bldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-pll"; + }; + + reg_bldo3: bldo3 { + /* unused */ + }; + + reg_bldo4: bldo4 { + /* unused */ + }; + + reg_cldo1: cldo1 { /* 5096000.codec */ + /* unused */ + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "axp717-cldo1"; + }; + + reg_cldo2: cldo2 { + /* unused */ + + }; + + reg_cldo3: cldo3 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-io"; + }; + + reg_cldo4: cldo4 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; + }; + + reg_boost: boost { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5200000>; + regulator-name = "boost"; + }; + + reg_cpusldo: cpusldo { + /* unused */ + }; + }; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_ph_pins>; + status = "okay"; +}; + +&pio { + vcc-pa-supply = <®_cldo3>; + vcc-pc-supply = <®_cldo3>; + vcc-pe-supply = <®_cldo3>; + vcc-pf-supply = <®_cldo3>; + vcc-pg-supply = <®_aldo4>; + vcc-ph-supply = <®_cldo3>; + vcc-pi-supply = <®_cldo3>; +}; + +/* the AXP717 has USB type-C role switch functionality, not yet described by the binding */ +&usbotg { + dr_mode = "peripheral"; /* USB type-C receptable */ + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; -- 2.44.0
