On Mon, Apr 15, 2024 at 04:08:10PM +0100, Kieran Bingham wrote:
> Hi Chris,
>
>
> Quoting Christopher Obbard (2024-04-15 12:41:27)
> > Enable the HDMI output on the Debix Model A SBC, using the HDMI encoder
> > present in the i.MX8MP SoC.
>
> Aha, you beat me to it. I have a commit locally (Dated 2022-09-06) but
> not sent because I didn't realise the HDMI support finally got upstream
> \o/
>
> > Signed-off-by: Christopher Obbard <chris.obbard@xxxxxxxxxxxxx>
> > ---
> >
> > .../dts/freescale/imx8mp-debix-model-a.dts | 47 +++++++++++++++++++
> > 1 file changed, 47 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts b/arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts
> > index 2c19766ebf09..29529c2ecac9 100644
> > --- a/arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts
> > +++ b/arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts
> > @@ -20,6 +20,18 @@ chosen {
> > stdout-path = &uart2;
> > };
> >
> > + hdmi-connector {
> > + compatible = "hdmi-connector";
> > + label = "hdmi";
> > + type = "a";
> > +
> > + port {
> > + hdmi_connector_in: endpoint {
> > + remote-endpoint = <&hdmi_tx_out>;
> > + };
> > + };
> > + };
> > +
>
> Interesting. My patch missed this. But it looks correct.
>
> > leds {
> > compatible = "gpio-leds";
> > pinctrl-names = "default";
> > @@ -94,6 +106,28 @@ ethphy0: ethernet-phy@0 { /* RTL8211E */
> > };
> > };
> >
> > +&hdmi_pvi {
> > + status = "okay";
> > +};
> > +
> > +&hdmi_tx {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_hdmi>;
> > + status = "okay";
> > +
> > + ports {
> > + port@1 {
> > + hdmi_tx_out: endpoint {
> > + remote-endpoint = <&hdmi_connector_in>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&hdmi_tx_phy {
> > + status = "okay";
> > +};
> > +
> > &i2c1 {
> > clock-frequency = <400000>;
> > pinctrl-names = "default";
> > @@ -241,6 +275,10 @@ &i2c6 {
> > status = "okay";
> > };
> >
> > +&lcdif3 {
> > + status = "okay";
> > +};
> > +
>
> Except for the addition of the connector, the above matches my patch to
> here.
>
> > &snvs_pwrkey {
> > status = "okay";
> > };
>
> But in my patch I have the following hunk here: (I haven't checked to
> see if this still applies on mainline, so take with a pinch of salt if
> it's not there!)
>
>
> &iomuxc {
> pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_hog>;
> -
> - pinctrl_hog: hoggrp {
> - fsl,pins = <
> - MX8MP_IOMUXC_HDMI_DDC_SCL__HDMIMIX_HDMI_SCL 0x400001c3
> - MX8MP_IOMUXC_HDMI_DDC_SDA__HDMIMIX_HDMI_SDA 0x400001c3
> - MX8MP_IOMUXC_HDMI_HPD__HDMIMIX_HDMI_HPD 0x40000019
> - MX8MP_IOMUXC_HDMI_CEC__HDMIMIX_HDMI_CEC 0x40000019
> - >;
> - };
>
> pinctrl_eqos: eqosgrp {
> fsl,pins = <
> MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC 0x3
> MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO 0x3
>
>
> > @@ -358,6 +396,15 @@ MX8MP_IOMUXC_NAND_READY_B__GPIO3_IO16 0x19
> > >;
> > };
> >
> > + pinctrl_hdmi: hdmigrp {
> > + fsl,pins = <
> > + MX8MP_IOMUXC_HDMI_DDC_SCL__HDMIMIX_HDMI_SCL 0x400001c3
> > + MX8MP_IOMUXC_HDMI_DDC_SDA__HDMIMIX_HDMI_SDA 0x400001c3
> > + MX8MP_IOMUXC_HDMI_HPD__HDMIMIX_HDMI_HPD 0x40000019
> > + MX8MP_IOMUXC_HDMI_CEC__HDMIMIX_HDMI_CEC 0x40000019
> > + >;
> > + };
> > +
>
> And my addition here is :
>
>
> + pinctrl_hdmi: hdmigrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_HDMI_DDC_SCL__HDMIMIX_HDMI_SCL 0x1c3
> + MX8MP_IOMUXC_HDMI_DDC_SDA__HDMIMIX_HDMI_SDA 0x1c3
> + MX8MP_IOMUXC_HDMI_HPD__HDMIMIX_HDMI_HPD 0x19
> + MX8MP_IOMUXC_HDMI_CEC__HDMIMIX_HDMI_CEC 0x19
> + >;
> + };
> +
>
>
> I haven't looked into what the 0x40000000 does yet, but just
> highlighting the difference from the version I've been using to make use
> of HDMI so far.
>
> Does anyone else know the impact here? Otherwise I'll try to find time
> to check this later. (For some undefined term of later...)
In drivers/pinctrl/freescale/pinctrl-imx.c,
#define IMX_NO_PAD_CTL 0x80000000 /* no pin config need */
#define IMX_PAD_SION 0x40000000 /* set SION */
The SION (Software Input ON) bit forces the input path active for the
pin. This can be used, for instance, to capture through GPIO the value
of a pin driven by a module. I'm not sure that's needed here.
> > pinctrl_i2c1: i2c1grp {
> > fsl,pins = <
> > MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c2
--
Regards,
Laurent Pinchart
