Hi Chris,
Quoting Christopher Obbard (2024-04-15 12:41:27)
> Enable the HDMI output on the Debix Model A SBC, using the HDMI encoder
> present in the i.MX8MP SoC.
Aha, you beat me to it. I have a commit locally (Dated 2022-09-06) but
not sent because I didn't realise the HDMI support finally got upstream
\o/
> Signed-off-by: Christopher Obbard <chris.obbard@xxxxxxxxxxxxx>
> ---
>
> .../dts/freescale/imx8mp-debix-model-a.dts | 47 +++++++++++++++++++
> 1 file changed, 47 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts b/arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts
> index 2c19766ebf09..29529c2ecac9 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts
> @@ -20,6 +20,18 @@ chosen {
> stdout-path = &uart2;
> };
>
> + hdmi-connector {
> + compatible = "hdmi-connector";
> + label = "hdmi";
> + type = "a";
> +
> + port {
> + hdmi_connector_in: endpoint {
> + remote-endpoint = <&hdmi_tx_out>;
> + };
> + };
> + };
> +
Interesting. My patch missed this. But it looks correct.
> leds {
> compatible = "gpio-leds";
> pinctrl-names = "default";
> @@ -94,6 +106,28 @@ ethphy0: ethernet-phy@0 { /* RTL8211E */
> };
> };
>
> +&hdmi_pvi {
> + status = "okay";
> +};
> +
> +&hdmi_tx {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hdmi>;
> + status = "okay";
> +
> + ports {
> + port@1 {
> + hdmi_tx_out: endpoint {
> + remote-endpoint = <&hdmi_connector_in>;
> + };
> + };
> + };
> +};
> +
> +&hdmi_tx_phy {
> + status = "okay";
> +};
> +
> &i2c1 {
> clock-frequency = <400000>;
> pinctrl-names = "default";
> @@ -241,6 +275,10 @@ &i2c6 {
> status = "okay";
> };
>
> +&lcdif3 {
> + status = "okay";
> +};
> +
Except for the addition of the connector, the above matches my patch to
here.
> &snvs_pwrkey {
> status = "okay";
> };
But in my patch I have the following hunk here: (I haven't checked to
see if this still applies on mainline, so take with a pinch of salt if
it's not there!)
&iomuxc {
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_hog>;
-
- pinctrl_hog: hoggrp {
- fsl,pins = <
- MX8MP_IOMUXC_HDMI_DDC_SCL__HDMIMIX_HDMI_SCL 0x400001c3
- MX8MP_IOMUXC_HDMI_DDC_SDA__HDMIMIX_HDMI_SDA 0x400001c3
- MX8MP_IOMUXC_HDMI_HPD__HDMIMIX_HDMI_HPD 0x40000019
- MX8MP_IOMUXC_HDMI_CEC__HDMIMIX_HDMI_CEC 0x40000019
- >;
- };
pinctrl_eqos: eqosgrp {
fsl,pins = <
MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC 0x3
MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO 0x3
> @@ -358,6 +396,15 @@ MX8MP_IOMUXC_NAND_READY_B__GPIO3_IO16 0x19
> >;
> };
>
> + pinctrl_hdmi: hdmigrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_HDMI_DDC_SCL__HDMIMIX_HDMI_SCL 0x400001c3
> + MX8MP_IOMUXC_HDMI_DDC_SDA__HDMIMIX_HDMI_SDA 0x400001c3
> + MX8MP_IOMUXC_HDMI_HPD__HDMIMIX_HDMI_HPD 0x40000019
> + MX8MP_IOMUXC_HDMI_CEC__HDMIMIX_HDMI_CEC 0x40000019
> + >;
> + };
> +
And my addition here is :
+ pinctrl_hdmi: hdmigrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_HDMI_DDC_SCL__HDMIMIX_HDMI_SCL 0x1c3
+ MX8MP_IOMUXC_HDMI_DDC_SDA__HDMIMIX_HDMI_SDA 0x1c3
+ MX8MP_IOMUXC_HDMI_HPD__HDMIMIX_HDMI_HPD 0x19
+ MX8MP_IOMUXC_HDMI_CEC__HDMIMIX_HDMI_CEC 0x19
+ >;
+ };
+
I haven't looked into what the 0x40000000 does yet, but just
highlighting the difference from the version I've been using to make use
of HDMI so far.
Does anyone else know the impact here? Otherwise I'll try to find time
to check this later. (For some undefined term of later...)
--
Kieran
> pinctrl_i2c1: i2c1grp {
> fsl,pins = <
> MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c2
> --
> 2.43.0
>
