Re: [PATCH v3 1/4] ARM: dts: qcom: msm8974: Split out common part of samsung-klte

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



在 2024-04-14星期日的 21:58 +0800,Icenowy Zheng写道:
> 在 2024-02-13星期二的 18:58 +0800,Rong Zhang写道:
> > Samsung Galaxy S5 has many variants. Variants that support LTE use
> > klte*
> > as their codename. Currently, the only supported one is the one
> > without
> > any suffix, namely, klte. It is known that other klte* variants
> > have
> > only minor differences compared to klte and can mostly work with
> > the
> > klte DTB.
> > 
> > Split the common part into a common DTSI so that it can be imported
> > in
> > the DTS of klte and other klte* variants.
> > 
> > Signed-off-by: Rong Zhang <i@xxxxxxxx>
> > ---
> >  ... qcom-msm8974pro-samsung-klte-common.dtsi} |   7 +-
> >  .../dts/qcom/qcom-msm8974pro-samsung-klte.dts | 833
> 
> Patched tested by picking into postmarketOS (a kltechn kernel variant
> is already added there).
> 
> Tested-by: Icenowy Zheng <uwu@xxxxxxxxxx>

Sorry I wrongly sent it to the 1/4 patch, this should be sent to the
cover letter, and this Tested-by tag applies to all 4 patches.

> 
> > +-----------------
> >  2 files changed, 17 insertions(+), 823 deletions(-)
> >  copy arch/arm/boot/dts/qcom/{qcom-msm8974pro-samsung-klte.dts =>
> > qcom-msm8974pro-samsung-klte-common.dtsi} (98%)
> >  rewrite arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts
> > (99%)
> > 
> > diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-
> > klte.dts
> > b/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte-common.dtsi
> > similarity index 98%
> > copy from arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts
> > copy to arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte-
> > common.dtsi
> > index b93539e2b87e..11e35b34ebd6 100644
> > --- a/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts
> > +++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte-
> > common.dtsi
> > @@ -6,8 +6,6 @@
> >  #include <dt-bindings/leds/common.h>
> >  
> >  / {
> > -       model = "Samsung Galaxy S5";
> > -       compatible = "samsung,klte", "qcom,msm8974pro",
> > "qcom,msm8974";
> >         chassis-type = "handset";
> >  
> >         aliases {
> > @@ -77,12 +75,10 @@ touchkey@20 {
> >                 };
> >         };
> >  
> > -       i2c-gpio-led {
> > +       i2c_led_gpio: i2c-gpio-led {
> >                 compatible = "i2c-gpio";
> >                 #address-cells = <1>;
> >                 #size-cells = <0>;
> > -               scl-gpios = <&tlmm 121 (GPIO_ACTIVE_HIGH |
> > GPIO_OPEN_DRAIN)>;
> > -               sda-gpios = <&tlmm 120 (GPIO_ACTIVE_HIGH |
> > GPIO_OPEN_DRAIN)>;
> >                 pinctrl-names = "default";
> >                 pinctrl-0 = <&i2c_led_gpioex_pins>;
> >  
> > @@ -770,7 +766,6 @@ i2c_touchkey_pins: i2c-touchkey-state {
> >         };
> >  
> >         i2c_led_gpioex_pins: i2c-led-gpioex-state {
> > -               pins = "gpio120", "gpio121";
> >                 function = "gpio";
> >                 bias-pull-down;
> >         };
> > diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-
> > klte.dts
> > b/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts
> > dissimilarity index 99%
> > index b93539e2b87e..954665f3a9dd 100644
> > --- a/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts
> > +++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts
> > @@ -1,817 +1,16 @@
> > -// SPDX-License-Identifier: GPL-2.0
> > -#include "qcom-msm8974pro.dtsi"
> > -#include "pma8084.dtsi"
> > -#include <dt-bindings/input/input.h>
> > -#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> > -#include <dt-bindings/leds/common.h>
> > -
> > -/ {
> > -       model = "Samsung Galaxy S5";
> > -       compatible = "samsung,klte", "qcom,msm8974pro",
> > "qcom,msm8974";
> > -       chassis-type = "handset";
> > -
> > -       aliases {
> > -               serial0 = &blsp1_uart1;
> > -               mmc0 = &sdhc_1; /* SDC1 eMMC slot */
> > -               mmc1 = &sdhc_3; /* SDC2 SD card slot */
> > -       };
> > -
> > -       chosen {
> > -               stdout-path = "serial0:115200n8";
> > -       };
> > -
> > -       gpio-keys {
> > -               compatible = "gpio-keys";
> > -
> > -               pinctrl-names = "default";
> > -               pinctrl-0 = <&gpio_keys_pin_a>;
> > -
> > -               key-volume-down {
> > -                       label = "volume_down";
> > -                       gpios = <&pma8084_gpios 2 GPIO_ACTIVE_LOW>;
> > -                       linux,input-type = <1>;
> > -                       linux,code = <KEY_VOLUMEDOWN>;
> > -                       debounce-interval = <15>;
> > -               };
> > -
> > -               key-home {
> > -                       label = "home_key";
> > -                       gpios = <&pma8084_gpios 3 GPIO_ACTIVE_LOW>;
> > -                       linux,input-type = <1>;
> > -                       linux,code = <KEY_HOMEPAGE>;
> > -                       wakeup-source;
> > -                       debounce-interval = <15>;
> > -               };
> > -
> > -               key-volume-up {
> > -                       label = "volume_up";
> > -                       gpios = <&pma8084_gpios 5 GPIO_ACTIVE_LOW>;
> > -                       linux,input-type = <1>;
> > -                       linux,code = <KEY_VOLUMEUP>;
> > -                       debounce-interval = <15>;
> > -               };
> > -       };
> > -
> > -       i2c-gpio-touchkey {
> > -               compatible = "i2c-gpio";
> > -               #address-cells = <1>;
> > -               #size-cells = <0>;
> > -               sda-gpios = <&tlmm 95 (GPIO_ACTIVE_HIGH |
> > GPIO_OPEN_DRAIN)>;
> > -               scl-gpios = <&tlmm 96 (GPIO_ACTIVE_HIGH |
> > GPIO_OPEN_DRAIN)>;
> > -               pinctrl-names = "default";
> > -               pinctrl-0 = <&i2c_touchkey_pins>;
> > -
> > -               touchkey@20 {
> > -                       compatible = "cypress,tm2-touchkey";
> > -                       reg = <0x20>;
> > -
> > -                       interrupt-parent = <&pma8084_gpios>;
> > -                       interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
> > -                       pinctrl-names = "default";
> > -                       pinctrl-0 = <&touchkey_pin>;
> > -
> > -                       vcc-supply = <&max77826_ldo15>;
> > -                       vdd-supply = <&pma8084_l19>;
> > -
> > -                       linux,keycodes = <KEY_APPSELECT KEY_BACK>;
> > -               };
> > -       };
> > -
> > -       i2c-gpio-led {
> > -               compatible = "i2c-gpio";
> > -               #address-cells = <1>;
> > -               #size-cells = <0>;
> > -               scl-gpios = <&tlmm 121 (GPIO_ACTIVE_HIGH |
> > GPIO_OPEN_DRAIN)>;
> > -               sda-gpios = <&tlmm 120 (GPIO_ACTIVE_HIGH |
> > GPIO_OPEN_DRAIN)>;
> > -               pinctrl-names = "default";
> > -               pinctrl-0 = <&i2c_led_gpioex_pins>;
> > -
> > -               i2c-gpio,delay-us = <2>;
> > -
> > -               gpio_expander: gpio@20 {
> > -                       compatible = "nxp,pcal6416";
> > -                       reg = <0x20>;
> > -
> > -                       gpio-controller;
> > -                       #gpio-cells = <2>;
> > -
> > -                       vcc-supply = <&pma8084_s4>;
> > -
> > -                       pinctrl-names = "default";
> > -                       pinctrl-0 = <&gpioex_pin>;
> > -
> > -                       reset-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
> > -               };
> > -
> > -               led-controller@30 {
> > -                       compatible = "panasonic,an30259a";
> > -                       reg = <0x30>;
> > -
> > -                       #address-cells = <1>;
> > -                       #size-cells = <0>;
> > -
> > -                       led@1 {
> > -                               reg = <1>;
> > -                               function = LED_FUNCTION_STATUS;
> > -                               color = <LED_COLOR_ID_RED>;
> > -                       };
> > -
> > -                       led@2 {
> > -                               reg = <2>;
> > -                               function = LED_FUNCTION_STATUS;
> > -                               color = <LED_COLOR_ID_GREEN>;
> > -                       };
> > -
> > -                       led@3 {
> > -                               reg = <3>;
> > -                               function = LED_FUNCTION_STATUS;
> > -                               color = <LED_COLOR_ID_BLUE>;
> > -                       };
> > -               };
> > -       };
> > -
> > -       vreg_wlan: wlan-regulator {
> > -               compatible = "regulator-fixed";
> > -
> > -               regulator-name = "wl-reg";
> > -               regulator-min-microvolt = <3300000>;
> > -               regulator-max-microvolt = <3300000>;
> > -
> > -               gpio = <&gpio_expander 8 GPIO_ACTIVE_HIGH>;
> > -               enable-active-high;
> > -       };
> > -
> > -       vreg_panel: panel-regulator {
> > -               compatible = "regulator-fixed";
> > -
> > -               pinctrl-names = "default";
> > -               pinctrl-0 = <&panel_en_pin>;
> > -
> > -               regulator-name = "panel-vddr-reg";
> > -               regulator-min-microvolt = <1500000>;
> > -               regulator-max-microvolt = <1500000>;
> > -
> > -               gpio = <&pma8084_gpios 14 GPIO_ACTIVE_HIGH>;
> > -               enable-active-high;
> > -       };
> > -
> > -       vreg_vph_pwr: vreg-vph-pwr {
> > -               compatible = "regulator-fixed";
> > -               regulator-name = "vph-pwr";
> > -
> > -               regulator-min-microvolt = <3600000>;
> > -               regulator-max-microvolt = <3600000>;
> > -
> > -               regulator-always-on;
> > -       };
> > -};
> > -
> > -&blsp1_i2c2 {
> > -       status = "okay";
> > -
> > -       touchscreen@20 {
> > -               compatible = "syna,rmi4-i2c";
> > -               reg = <0x20>;
> > -
> > -               interrupt-parent = <&pma8084_gpios>;
> > -               interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
> > -
> > -               vdd-supply = <&max77826_ldo13>;
> > -               vio-supply = <&pma8084_lvs2>;
> > -
> > -               pinctrl-names = "default";
> > -               pinctrl-0 = <&touch_pin>;
> > -
> > -               syna,startup-delay-ms = <100>;
> > -
> > -               #address-cells = <1>;
> > -               #size-cells = <0>;
> > -
> > -               rmi4-f01@1 {
> > -                       reg = <0x1>;
> > -                       syna,nosleep-mode = <1>;
> > -               };
> > -
> > -               rmi4-f12@12 {
> > -                       reg = <0x12>;
> > -                       syna,sensor-type = <1>;
> > -               };
> > -       };
> > -};
> > -
> > -&blsp1_i2c6 {
> > -       status = "okay";
> > -
> > -       pmic@60 {
> > -               reg = <0x60>;
> > -               compatible = "maxim,max77826";
> > -
> > -               regulators {
> > -                       max77826_ldo1: LDO1 {
> > -                               regulator-min-microvolt =
> > <1200000>;
> > -                               regulator-max-microvolt =
> > <1200000>;
> > -                       };
> > -
> > -                       max77826_ldo2: LDO2 {
> > -                               regulator-min-microvolt =
> > <1000000>;
> > -                               regulator-max-microvolt =
> > <1000000>;
> > -                       };
> > -
> > -                       max77826_ldo3: LDO3 {
> > -                               regulator-min-microvolt =
> > <1200000>;
> > -                               regulator-max-microvolt =
> > <1200000>;
> > -                       };
> > -
> > -                       max77826_ldo4: LDO4 {
> > -                               regulator-min-microvolt =
> > <1800000>;
> > -                               regulator-max-microvolt =
> > <1800000>;
> > -                       };
> > -
> > -                       max77826_ldo5: LDO5 {
> > -                               regulator-min-microvolt =
> > <1800000>;
> > -                               regulator-max-microvolt =
> > <1800000>;
> > -                       };
> > -
> > -                       max77826_ldo6: LDO6 {
> > -                               regulator-min-microvolt =
> > <1800000>;
> > -                               regulator-max-microvolt =
> > <3300000>;
> > -                       };
> > -
> > -                       max77826_ldo7: LDO7 {
> > -                               regulator-min-microvolt =
> > <1800000>;
> > -                               regulator-max-microvolt =
> > <1800000>;
> > -                       };
> > -
> > -                       max77826_ldo8: LDO8 {
> > -                               regulator-min-microvolt =
> > <1800000>;
> > -                               regulator-max-microvolt =
> > <3300000>;
> > -                       };
> > -
> > -                       max77826_ldo9: LDO9 {
> > -                               regulator-min-microvolt =
> > <1800000>;
> > -                               regulator-max-microvolt =
> > <1800000>;
> > -                       };
> > -
> > -                       max77826_ldo10: LDO10 {
> > -                               regulator-min-microvolt =
> > <2800000>;
> > -                               regulator-max-microvolt =
> > <2950000>;
> > -                       };
> > -
> > -                       max77826_ldo11: LDO11 {
> > -                               regulator-min-microvolt =
> > <2700000>;
> > -                               regulator-max-microvolt =
> > <2950000>;
> > -                       };
> > -
> > -                       max77826_ldo12: LDO12 {
> > -                               regulator-min-microvolt =
> > <2500000>;
> > -                               regulator-max-microvolt =
> > <3300000>;
> > -                       };
> > -
> > -                       max77826_ldo13: LDO13 {
> > -                               regulator-min-microvolt =
> > <3300000>;
> > -                               regulator-max-microvolt =
> > <3300000>;
> > -                       };
> > -
> > -                       max77826_ldo14: LDO14 {
> > -                               regulator-min-microvolt =
> > <3300000>;
> > -                               regulator-max-microvolt =
> > <3300000>;
> > -                       };
> > -
> > -                       max77826_ldo15: LDO15 {
> > -                               regulator-min-microvolt =
> > <1800000>;
> > -                               regulator-max-microvolt =
> > <1800000>;
> > -                       };
> > -
> > -                       max77826_buck: BUCK {
> > -                               regulator-min-microvolt =
> > <1225000>;
> > -                               regulator-max-microvolt =
> > <1225000>;
> > -                       };
> > -
> > -                       max77826_buckboost: BUCKBOOST {
> > -                               regulator-min-microvolt =
> > <3400000>;
> > -                               regulator-max-microvolt =
> > <3400000>;
> > -                       };
> > -               };
> > -       };
> > -};
> > -
> > -&blsp1_uart2 {
> > -       status = "okay";
> > -};
> > -
> > -&blsp2_i2c6 {
> > -       status = "okay";
> > -
> > -       fuelgauge@36 {
> > -               compatible = "maxim,max17048";
> > -               reg = <0x36>;
> > -
> > -               maxim,double-soc;
> > -               maxim,rcomp = /bits/ 8 <0x56>;
> > -
> > -               interrupt-parent = <&pma8084_gpios>;
> > -               interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
> > -
> > -               pinctrl-names = "default";
> > -               pinctrl-0 = <&fuelgauge_pin>;
> > -       };
> > -};
> > -
> > -&blsp2_uart2 {
> > -       status = "okay";
> > -
> > -       pinctrl-names = "default", "sleep";
> > -       pinctrl-0 = <&blsp2_uart2_pins_active>;
> > -       pinctrl-1 = <&blsp2_uart2_pins_sleep>;
> > -
> > -       bluetooth {
> > -               compatible = "brcm,bcm43540-bt";
> > -               max-speed = <3000000>;
> > -               pinctrl-names = "default";
> > -               pinctrl-0 = <&bt_pins>;
> > -               device-wakeup-gpios = <&tlmm 91 GPIO_ACTIVE_HIGH>;
> > -               shutdown-gpios = <&gpio_expander 9
> > GPIO_ACTIVE_HIGH>;
> > -               interrupt-parent = <&tlmm>;
> > -               interrupts = <75 IRQ_TYPE_LEVEL_HIGH>;
> > -               interrupt-names = "host-wakeup";
> > -       };
> > -};
> > -
> > -&gpu {
> > -       status = "okay";
> > -};
> > -
> > -&mdss {
> > -       status = "okay";
> > -};
> > -
> > -&mdss_dsi0 {
> > -       status = "okay";
> > -
> > -       vdda-supply = <&pma8084_l2>;
> > -       vdd-supply = <&pma8084_l22>;
> > -       vddio-supply = <&pma8084_l12>;
> > -
> > -       panel: panel@0 {
> > -               reg = <0>;
> > -               compatible = "samsung,s6e3fa2";
> > -
> > -               pinctrl-names = "default";
> > -               pinctrl-0 = <&panel_te_pin &panel_rst_pin>;
> > -
> > -               iovdd-supply = <&pma8084_lvs4>;
> > -               vddr-supply = <&vreg_panel>;
> > -
> > -               reset-gpios = <&pma8084_gpios 17 GPIO_ACTIVE_LOW>;
> > -
> > -               port {
> > -                       panel_in: endpoint {
> > -                               remote-endpoint = <&mdss_dsi0_out>;
> > -                       };
> > -               };
> > -       };
> > -};
> > -
> > -&mdss_dsi0_out {
> > -       remote-endpoint = <&panel_in>;
> > -       data-lanes = <0 1 2 3>;
> > -};
> > -
> > -&mdss_dsi0_phy {
> > -       status = "okay";
> > -
> > -       vddio-supply = <&pma8084_l12>;
> > -};
> > -
> > -&pma8084_gpios {
> > -       gpio_keys_pin_a: gpio-keys-active-state {
> > -               pins = "gpio2", "gpio3", "gpio5";
> > -               function = "normal";
> > -
> > -               bias-pull-up;
> > -               power-source = <PMA8084_GPIO_S4>;
> > -       };
> > -
> > -       touchkey_pin: touchkey-int-state {
> > -               pins = "gpio6";
> > -               function = "normal";
> > -               bias-disable;
> > -               input-enable;
> > -               power-source = <PMA8084_GPIO_S4>;
> > -       };
> > -
> > -       touch_pin: touchscreen-int-state {
> > -               pins = "gpio8";
> > -               function = "normal";
> > -               bias-disable;
> > -               input-enable;
> > -               power-source = <PMA8084_GPIO_S4>;
> > -       };
> > -
> > -       panel_en_pin: panel-en-state {
> > -               pins = "gpio14";
> > -               function = "normal";
> > -               bias-pull-up;
> > -               power-source = <PMA8084_GPIO_S4>;
> > -               qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
> > -       };
> > -
> > -       wlan_sleep_clk_pin: wlan-sleep-clk-state {
> > -               pins = "gpio16";
> > -               function = "func2";
> > -
> > -               output-high;
> > -               power-source = <PMA8084_GPIO_S4>;
> > -               qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
> > -       };
> > -
> > -       panel_rst_pin: panel-rst-state {
> > -               pins = "gpio17";
> > -               function = "normal";
> > -               bias-disable;
> > -               power-source = <PMA8084_GPIO_S4>;
> > -               qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
> > -       };
> > -
> > -       fuelgauge_pin: fuelgauge-int-state {
> > -               pins = "gpio21";
> > -               function = "normal";
> > -               bias-disable;
> > -               input-enable;
> > -               power-source = <PMA8084_GPIO_S4>;
> > -       };
> > -};
> > -
> > -&remoteproc_adsp {
> > -       status = "okay";
> > -       cx-supply = <&pma8084_s2>;
> > -};
> > -
> > -&remoteproc_mss {
> > -       status = "okay";
> > -       cx-supply = <&pma8084_s2>;
> > -       mss-supply = <&pma8084_s6>;
> > -       mx-supply = <&pma8084_s1>;
> > -       pll-supply = <&pma8084_l12>;
> > -};
> > -
> > -&rpm_requests {
> > -       regulators-0 {
> > -               compatible = "qcom,rpm-pma8084-regulators";
> > -
> > -               pma8084_s1: s1 {
> > -                       regulator-min-microvolt = <675000>;
> > -                       regulator-max-microvolt = <1050000>;
> > -                       regulator-always-on;
> > -               };
> > -
> > -               pma8084_s2: s2 {
> > -                       regulator-min-microvolt = <500000>;
> > -                       regulator-max-microvolt = <1050000>;
> > -               };
> > -
> > -               pma8084_s3: s3 {
> > -                       regulator-min-microvolt = <1300000>;
> > -                       regulator-max-microvolt = <1300000>;
> > -               };
> > -
> > -               pma8084_s4: s4 {
> > -                       regulator-min-microvolt = <1800000>;
> > -                       regulator-max-microvolt = <1800000>;
> > -               };
> > -
> > -               pma8084_s5: s5 {
> > -                       regulator-min-microvolt = <2150000>;
> > -                       regulator-max-microvolt = <2150000>;
> > -               };
> > -
> > -               pma8084_s6: s6 {
> > -                       regulator-min-microvolt = <1050000>;
> > -                       regulator-max-microvolt = <1050000>;
> > -               };
> > -
> > -               pma8084_l1: l1 {
> > -                       regulator-min-microvolt = <1225000>;
> > -                       regulator-max-microvolt = <1225000>;
> > -               };
> > -
> > -               pma8084_l2: l2 {
> > -                       regulator-min-microvolt = <1200000>;
> > -                       regulator-max-microvolt = <1200000>;
> > -               };
> > -
> > -               pma8084_l3: l3 {
> > -                       regulator-min-microvolt = <1050000>;
> > -                       regulator-max-microvolt = <1200000>;
> > -               };
> > -
> > -               pma8084_l4: l4 {
> > -                       regulator-min-microvolt = <1200000>;
> > -                       regulator-max-microvolt = <1225000>;
> > -               };
> > -
> > -               pma8084_l5: l5 {
> > -                       regulator-min-microvolt = <1800000>;
> > -                       regulator-max-microvolt = <1800000>;
> > -               };
> > -
> > -               pma8084_l6: l6 {
> > -                       regulator-min-microvolt = <1800000>;
> > -                       regulator-max-microvolt = <1800000>;
> > -               };
> > -
> > -               pma8084_l7: l7 {
> > -                       regulator-min-microvolt = <1800000>;
> > -                       regulator-max-microvolt = <1800000>;
> > -               };
> > -
> > -               pma8084_l8: l8 {
> > -                       regulator-min-microvolt = <1800000>;
> > -                       regulator-max-microvolt = <1800000>;
> > -               };
> > -
> > -               pma8084_l9: l9 {
> > -                       regulator-min-microvolt = <1800000>;
> > -                       regulator-max-microvolt = <2950000>;
> > -               };
> > -
> > -               pma8084_l10: l10 {
> > -                       regulator-min-microvolt = <1800000>;
> > -                       regulator-max-microvolt = <2950000>;
> > -               };
> > -
> > -               pma8084_l11: l11 {
> > -                       regulator-min-microvolt = <1300000>;
> > -                       regulator-max-microvolt = <1300000>;
> > -               };
> > -
> > -               pma8084_l12: l12 {
> > -                       regulator-min-microvolt = <1800000>;
> > -                       regulator-max-microvolt = <1800000>;
> > -                       regulator-always-on;
> > -               };
> > -
> > -               pma8084_l13: l13 {
> > -                       regulator-min-microvolt = <1800000>;
> > -                       regulator-max-microvolt = <2950000>;
> > -               };
> > -
> > -               pma8084_l14: l14 {
> > -                       regulator-min-microvolt = <1800000>;
> > -                       regulator-max-microvolt = <1800000>;
> > -               };
> > -
> > -               pma8084_l15: l15 {
> > -                       regulator-min-microvolt = <2050000>;
> > -                       regulator-max-microvolt = <2050000>;
> > -               };
> > -
> > -               pma8084_l16: l16 {
> > -                       regulator-min-microvolt = <2700000>;
> > -                       regulator-max-microvolt = <2700000>;
> > -               };
> > -
> > -               pma8084_l17: l17 {
> > -                       regulator-min-microvolt = <2850000>;
> > -                       regulator-max-microvolt = <2850000>;
> > -               };
> > -
> > -               pma8084_l18: l18 {
> > -                       regulator-min-microvolt = <2850000>;
> > -                       regulator-max-microvolt = <2850000>;
> > -               };
> > -
> > -               pma8084_l19: l19 {
> > -                       regulator-min-microvolt = <3300000>;
> > -                       regulator-max-microvolt = <3300000>;
> > -               };
> > -
> > -               pma8084_l20: l20 {
> > -                       regulator-min-microvolt = <2950000>;
> > -                       regulator-max-microvolt = <2950000>;
> > -                       regulator-system-load = <200000>;
> > -                       regulator-allow-set-load;
> > -               };
> > -
> > -               pma8084_l21: l21 {
> > -                       regulator-min-microvolt = <2950000>;
> > -                       regulator-max-microvolt = <2950000>;
> > -                       regulator-system-load = <200000>;
> > -                       regulator-allow-set-load;
> > -               };
> > -
> > -               pma8084_l22: l22 {
> > -                       regulator-min-microvolt = <3000000>;
> > -                       regulator-max-microvolt = <3300000>;
> > -               };
> > -
> > -               pma8084_l23: l23 {
> > -                       regulator-min-microvolt = <3000000>;
> > -                       regulator-max-microvolt = <3000000>;
> > -               };
> > -
> > -               pma8084_l24: l24 {
> > -                       regulator-min-microvolt = <3075000>;
> > -                       regulator-max-microvolt = <3075000>;
> > -               };
> > -
> > -               pma8084_l25: l25 {
> > -                       regulator-min-microvolt = <2100000>;
> > -                       regulator-max-microvolt = <2100000>;
> > -               };
> > -
> > -               pma8084_l26: l26 {
> > -                       regulator-min-microvolt = <1800000>;
> > -                       regulator-max-microvolt = <2050000>;
> > -               };
> > -
> > -               pma8084_l27: l27 {
> > -                       regulator-min-microvolt = <1000000>;
> > -                       regulator-max-microvolt = <1225000>;
> > -               };
> > -
> > -               pma8084_lvs1: lvs1 {};
> > -               pma8084_lvs2: lvs2 {};
> > -               pma8084_lvs3: lvs3 {};
> > -               pma8084_lvs4: lvs4 {};
> > -
> > -               pma8084_5vs1: 5vs1 {};
> > -       };
> > -};
> > -
> > -&sdhc_1 {
> > -       status = "okay";
> > -
> > -       vmmc-supply = <&pma8084_l20>;
> > -       vqmmc-supply = <&pma8084_s4>;
> > -
> > -       pinctrl-names = "default", "sleep";
> > -       pinctrl-0 = <&sdc1_on>;
> > -       pinctrl-1 = <&sdc1_off>;
> > -};
> > -
> > -&sdhc_2 {
> > -       status = "okay";
> > -       max-frequency = <100000000>;
> > -       vmmc-supply = <&vreg_wlan>;
> > -       vqmmc-supply = <&pma8084_s4>;
> > -       non-removable;
> > -
> > -       pinctrl-names = "default", "sleep";
> > -       pinctrl-0 = <&sdc2_on>;
> > -       pinctrl-1 = <&sdc2_off>;
> > -
> > -       wifi@1 {
> > -               reg = <1>;
> > -               compatible = "brcm,bcm4329-fmac";
> > -
> > -               interrupt-parent = <&tlmm>;
> > -               interrupts = <92 IRQ_TYPE_LEVEL_HIGH>;
> > -               interrupt-names = "host-wake";
> > -
> > -               pinctrl-names = "default";
> > -               pinctrl-0 = <&wlan_sleep_clk_pin &wifi_pin>;
> > -       };
> > -};
> > -
> > -&sdhc_3 {
> > -       status = "okay";
> > -       max-frequency = <100000000>;
> > -       vmmc-supply = <&pma8084_l21>;
> > -       vqmmc-supply = <&pma8084_l13>;
> > -
> > -       /*
> > -        * cd-gpio is intentionally disabled. If enabled, an SD
> > card
> > -        * present during boot is not initialized correctly.
> > Without
> > -        * cd-gpios the driver resorts to polling, so hotplug
> > works.
> > -        */
> > -       pinctrl-names = "default";
> > -       pinctrl-0 = <&sdc3_on /* &sdhc3_cd_pin */>;
> > -       /* cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>; */
> > -};
> > -
> > -&tlmm {
> > -       /* This seems suspicious, but somebody with this device
> > should look into it. */
> > -       blsp2_uart2_pins_active: blsp2-uart2-pins-active-state {
> > -               pins = "gpio45", "gpio46", "gpio47", "gpio48";
> > -               function = "blsp_uart8";
> > -               drive-strength = <8>;
> > -               bias-disable;
> > -       };
> > -
> > -       blsp2_uart2_pins_sleep: blsp2-uart2-pins-sleep-state {
> > -               pins = "gpio45", "gpio46", "gpio47", "gpio48";
> > -               function = "gpio";
> > -               drive-strength = <2>;
> > -               bias-pull-down;
> > -       };
> > -
> > -       bt_pins: bt-pins-state {
> > -               hostwake-pins {
> > -                       pins = "gpio75";
> > -                       function = "gpio";
> > -                       drive-strength = <16>;
> > -               };
> > -
> > -               devwake-pins {
> > -                       pins = "gpio91";
> > -                       function = "gpio";
> > -                       drive-strength = <2>;
> > -               };
> > -       };
> > -
> > -       sdc1_on: sdhc1-on-state {
> > -               clk-pins {
> > -                       pins = "sdc1_clk";
> > -                       drive-strength = <4>;
> > -                       bias-disable;
> > -               };
> > -
> > -               cmd-data-pins {
> > -                       pins = "sdc1_cmd", "sdc1_data";
> > -                       drive-strength = <4>;
> > -                       bias-pull-up;
> > -               };
> > -       };
> > -
> > -       sdc3_on: sdc3-on-state {
> > -               pins = "gpio35", "gpio36", "gpio37", "gpio38",
> > "gpio39", "gpio40";
> > -               function = "sdc3";
> > -               drive-strength = <8>;
> > -               bias-disable;
> > -       };
> > -
> > -       sdhc3_cd_pin: sdc3-cd-on-state {
> > -               pins = "gpio62";
> > -               function = "gpio";
> > -
> > -               drive-strength = <2>;
> > -               bias-disable;
> > -       };
> > -
> > -       sdc2_on: sdhc2-on-state {
> > -               clk-pins {
> > -                       pins = "sdc2_clk";
> > -                       drive-strength = <6>;
> > -                       bias-disable;
> > -               };
> > -
> > -               cmd-data-pins {
> > -                       pins = "sdc2_cmd", "sdc2_data";
> > -                       drive-strength = <6>;
> > -                       bias-pull-up;
> > -               };
> > -       };
> > -
> > -       i2c_touchkey_pins: i2c-touchkey-state {
> > -               pins = "gpio95", "gpio96";
> > -               function = "gpio";
> > -               bias-pull-up;
> > -       };
> > -
> > -       i2c_led_gpioex_pins: i2c-led-gpioex-state {
> > -               pins = "gpio120", "gpio121";
> > -               function = "gpio";
> > -               bias-pull-down;
> > -       };
> > -
> > -       gpioex_pin: gpioex-state {
> > -               pins = "gpio145";
> > -               function = "gpio";
> > -               bias-pull-up;
> > -               drive-strength = <2>;
> > -       };
> > -
> > -       wifi_pin: wifi-state {
> > -               pins = "gpio92";
> > -               function = "gpio";
> > -               bias-pull-down;
> > -       };
> > -
> > -       panel_te_pin: panel-state {
> > -               pins = "gpio12";
> > -               function = "mdp_vsync";
> > -               drive-strength = <2>;
> > -               bias-disable;
> > -       };
> > -};
> > -
> > -&usb {
> > -       status = "okay";
> > -
> > -       phys = <&usb_hs1_phy>;
> > -       phy-select = <&tcsr 0xb000 0>;
> > -
> > -       hnp-disable;
> > -       srp-disable;
> > -       adp-disable;
> > -};
> > -
> > -&usb_hs1_phy {
> > -       status = "okay";
> > -
> > -       v1p8-supply = <&pma8084_l6>;
> > -       v3p3-supply = <&pma8084_l24>;
> > -
> > -       qcom,init-seq = /bits/ 8 <0x1 0x64>;
> > -};
> > +// SPDX-License-Identifier: GPL-2.0
> > +#include "qcom-msm8974pro-samsung-klte-common.dtsi"
> > +
> > +/ {
> > +       model = "Samsung Galaxy S5";
> > +       compatible = "samsung,klte", "qcom,msm8974pro",
> > "qcom,msm8974";
> > +};
> > +
> > +&i2c_led_gpio {
> > +       scl-gpios = <&tlmm 121 (GPIO_ACTIVE_HIGH |
> > GPIO_OPEN_DRAIN)>;
> > +       sda-gpios = <&tlmm 120 (GPIO_ACTIVE_HIGH |
> > GPIO_OPEN_DRAIN)>;
> > +};
> > +
> > +&i2c_led_gpioex_pins {
> > +       pins = "gpio120", "gpio121";
> > +};
> 





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux