On 10-02-24, 02:10, Daniel Golle wrote:
> Add driver for MediaTek's XFI T-PHY which can be found in the MT7988
What does XFI mean?
> SoC. The XFI T-PHY is a 10 Gigabit/s Ethernet SerDes PHY with muxes on
> the internal side to be used with either USXGMII PCS or LynxI PCS,
> depending on the selected PHY interface mode.
>
> The PHY can operates only in PHY_MODE_ETHERNET, the submode is one of
> PHY_INTERFACE_MODE_* corresponding to the supported modes:
>
> * USXGMII \
> * 10GBase-R }- USXGMII PCS - XGDM \
> * 5GBase-R / \
> }- Ethernet MAC
> * 2500Base-X \ /
> * 1000Base-X }- LynxI PCS - GDM /
> * Cisco SGMII (MAC side) /
>
> In order to work-around a performance issue present on the first of
> two XFI T-PHYs present in MT7988, special tuning is applied which can be
> selected by adding the 'mediatek,usxgmii-performance-errata' property to
> the device tree node.
>
> There is no documentation for most registers used for the
> analog/tuning part, however, most of the registers have been partially
> reverse-engineered from MediaTek's SDK implementation (an opaque
> sequence of 32-bit register writes) and descriptions for all relevant
> digital registers and bits such as resets and muxes have been supplied
> by MediaTek.
>
> Signed-off-by: Daniel Golle <daniel@xxxxxxxxxxxxxx>
> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxx>
> ---
> v3: no changes
> v2:
> * use IO helpers from mtk-io.h instead of rolling my own
> * use devm_clk_bulk_get()
> * yse devm_platform_ioremap_resource()
> * unify name and description everywhere
> * invert bool is_xgmii into bool use_lynxi_pcs and add comments
> describing the meaning of each of the stack variables
> * not much we can do about remaining magic values unless MTK provides
> definitions for them
>
>
> MAINTAINERS | 1 +
> drivers/phy/mediatek/Kconfig | 12 +
> drivers/phy/mediatek/Makefile | 1 +
> drivers/phy/mediatek/phy-mtk-xfi-tphy.c | 360 ++++++++++++++++++++++++
> 4 files changed, 374 insertions(+)
> create mode 100644 drivers/phy/mediatek/phy-mtk-xfi-tphy.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 4be2fd097f261..616b86e3e62fd 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -13776,6 +13776,7 @@ L: netdev@xxxxxxxxxxxxxxx
> S: Maintained
> F: drivers/net/phy/mediatek-ge-soc.c
> F: drivers/net/phy/mediatek-ge.c
> +F: drivers/phy/mediatek/phy-mtk-xfi-tphy.c
>
> MEDIATEK I2C CONTROLLER DRIVER
> M: Qii Wang <qii.wang@xxxxxxxxxxxx>
> diff --git a/drivers/phy/mediatek/Kconfig b/drivers/phy/mediatek/Kconfig
> index 3849b7c87d287..117d0e84c7360 100644
> --- a/drivers/phy/mediatek/Kconfig
> +++ b/drivers/phy/mediatek/Kconfig
> @@ -13,6 +13,18 @@ config PHY_MTK_PCIE
> callback for PCIe GEN3 port, it supports software efuse
> initialization.
>
> +config PHY_MTK_XFI_TPHY
> + tristate "MediaTek 10GE SerDes XFI T-PHY driver"
> + depends on ARCH_MEDIATEK || COMPILE_TEST
> + depends on OF && OF_ADDRESS
why both, is OF not enough?
> + depends on HAS_IOMEM
> + select GENERIC_PHY
> + help
> + Say 'Y' here to add support for MediaTek XFI T-PHY driver.
> + The driver provides access to the Ethernet SerDes T-PHY supporting
> + 1GE and 2.5GE modes via the LynxI PCS, and 5GE and 10GE modes
> + via the USXGMII PCS found in MediaTek SoCs with 10G Ethernet.
> +
> config PHY_MTK_TPHY
> tristate "MediaTek T-PHY Driver"
> depends on ARCH_MEDIATEK || COMPILE_TEST
> diff --git a/drivers/phy/mediatek/Makefile b/drivers/phy/mediatek/Makefile
> index f6e24a47e0815..1b8088df71e84 100644
> --- a/drivers/phy/mediatek/Makefile
> +++ b/drivers/phy/mediatek/Makefile
> @@ -8,6 +8,7 @@ obj-$(CONFIG_PHY_MTK_PCIE) += phy-mtk-pcie.o
> obj-$(CONFIG_PHY_MTK_TPHY) += phy-mtk-tphy.o
> obj-$(CONFIG_PHY_MTK_UFS) += phy-mtk-ufs.o
> obj-$(CONFIG_PHY_MTK_XSPHY) += phy-mtk-xsphy.o
> +obj-$(CONFIG_PHY_MTK_XFI_TPHY) += phy-mtk-xfi-tphy.o
>
> phy-mtk-hdmi-drv-y := phy-mtk-hdmi.o
> phy-mtk-hdmi-drv-y += phy-mtk-hdmi-mt2701.o
> diff --git a/drivers/phy/mediatek/phy-mtk-xfi-tphy.c b/drivers/phy/mediatek/phy-mtk-xfi-tphy.c
> new file mode 100644
> index 0000000000000..551d6cee33f94
> --- /dev/null
> +++ b/drivers/phy/mediatek/phy-mtk-xfi-tphy.c
> @@ -0,0 +1,360 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/* MediaTek 10GE SerDes XFI T-PHY driver
> + *
> + * Copyright (c) 2024 Daniel Golle <daniel@xxxxxxxxxxxxxx>
> + * Bc-bocun Chen <bc-bocun.chen@xxxxxxxxxxxx>
> + * based on mtk_usxgmii.c and mtk_sgmii.c found in MediaTek's SDK (GPL-2.0)
> + * Copyright (c) 2022 MediaTek Inc.
> + * Author: Henry Yen <henry.yen@xxxxxxxxxxxx>
> + */
> +
> +#include <linux/module.h>
> +#include <linux/device.h>
> +#include <linux/platform_device.h>
> +#include <linux/of.h>
> +#include <linux/io.h>
> +#include <linux/clk.h>
> +#include <linux/reset.h>
> +#include <linux/phy.h>
> +#include <linux/phy/phy.h>
> +
> +#include "phy-mtk-io.h"
> +
> +#define MTK_XFI_TPHY_NUM_CLOCKS 2
> +
> +#define REG_DIG_GLB_70 0x0070
> +#define XTP_PCS_RX_EQ_IN_PROGRESS(x) FIELD_PREP(GENMASK(25, 24), (x))
> +#define XTP_PCS_MODE_MASK GENMASK(17, 16)
> +#define XTP_PCS_MODE(x) FIELD_PREP(GENMASK(17, 16), (x))
> +#define XTP_PCS_RST_B BIT(15)
> +#define XTP_FRC_PCS_RST_B BIT(14)
> +#define XTP_PCS_PWD_SYNC_MASK GENMASK(13, 12)
> +#define XTP_PCS_PWD_SYNC(x) FIELD_PREP(XTP_PCS_PWD_SYNC_MASK, (x))
> +#define XTP_PCS_PWD_ASYNC_MASK GENMASK(11, 10)
> +#define XTP_PCS_PWD_ASYNC(x) FIELD_PREP(XTP_PCS_PWD_ASYNC_MASK, (x))
> +#define XTP_FRC_PCS_PWD_ASYNC BIT(8)
> +#define XTP_PCS_UPDT BIT(4)
> +#define XTP_PCS_IN_FR_RG BIT(0)
> +
> +#define REG_DIG_GLB_F4 0x00f4
> +#define XFI_DPHY_PCS_SEL BIT(0)
> +#define XFI_DPHY_PCS_SEL_SGMII FIELD_PREP(XFI_DPHY_PCS_SEL, 1)
> +#define XFI_DPHY_PCS_SEL_USXGMII FIELD_PREP(XFI_DPHY_PCS_SEL, 0)
> +#define XFI_DPHY_AD_SGDT_FRC_EN BIT(5)
> +
> +#define REG_DIG_LN_TRX_40 0x3040
> +#define XTP_LN_FRC_TX_DATA_EN BIT(29)
> +#define XTP_LN_TX_DATA_EN BIT(28)
> +
> +#define REG_DIG_LN_TRX_B0 0x30b0
> +#define XTP_LN_FRC_TX_MACCK_EN BIT(5)
> +#define XTP_LN_TX_MACCK_EN BIT(4)
> +
> +#define REG_ANA_GLB_D0 0x90d0
> +#define XTP_GLB_USXGMII_SEL_MASK GENMASK(3, 1)
> +#define XTP_GLB_USXGMII_SEL(x) FIELD_PREP(GENMASK(3, 1), (x))
> +#define XTP_GLB_USXGMII_EN BIT(0)
> +
> +struct mtk_xfi_tphy {
> + void __iomem *base;
> + struct device *dev;
> + struct reset_control *reset;
> + struct clk_bulk_data clocks[MTK_XFI_TPHY_NUM_CLOCKS];
> + bool da_war;
> +};
> +
> +static void mtk_xfi_tphy_setup(struct mtk_xfi_tphy *xfi_tphy,
> + phy_interface_t interface)
> +{
> + /* Override 10GBase-R tuning value if work-around is selected */
> + bool da_war = (xfi_tphy->da_war && (interface == PHY_INTERFACE_MODE_10GBASER));
why do you need braces around this?
> + /* Bools to make setting up values for specific PHY speeds easier */
> + bool is_2p5g = (interface == PHY_INTERFACE_MODE_2500BASEX);
> + bool is_1g = (interface == PHY_INTERFACE_MODE_1000BASEX ||
> + interface == PHY_INTERFACE_MODE_SGMII);
> + bool is_10g = (interface == PHY_INTERFACE_MODE_10GBASER ||
> + interface == PHY_INTERFACE_MODE_USXGMII);
> + bool is_5g = (interface == PHY_INTERFACE_MODE_5GBASER);
> + /* Bool to configure input mux to either
> + * - USXGMII PCS (64b/66b coding) for 5G/10G
> + * - LynxI PCS (8b/10b coding) for 1G/2.5G
> + */
> + bool use_lynxi_pcs = (is_1g || is_2p5g);
This is quite terrible to read, how about declaring variables first and
then doing the initialization?
> +
> + dev_dbg(xfi_tphy->dev, "setting up for mode %s\n", phy_modes(interface));
> +
> + /* Setup PLL setting */
> + mtk_phy_update_bits(xfi_tphy->base + 0x9024, 0x100000, is_10g ? 0x0 : 0x100000);
> + mtk_phy_update_bits(xfi_tphy->base + 0x2020, 0x202000, is_5g ? 0x202000 : 0x0);
> + mtk_phy_update_bits(xfi_tphy->base + 0x2030, 0x500, is_1g ? 0x0 : 0x500);
> + mtk_phy_update_bits(xfi_tphy->base + 0x2034, 0xa00, is_1g ? 0x0 : 0xa00);
> + mtk_phy_update_bits(xfi_tphy->base + 0x2040, 0x340000, is_1g ? 0x200000 : 0x140000);
magic numbers?
> +
> + /* Setup RXFE BW setting */
> + mtk_phy_update_bits(xfi_tphy->base + 0x50f0, 0xc10, is_1g ? 0x410 : is_5g ? 0x800 : 0x400);
> + mtk_phy_update_bits(xfi_tphy->base + 0x50e0, 0x4000, is_5g ? 0x0 : 0x4000);
> +
> + /* Setup RX CDR setting */
> + mtk_phy_update_bits(xfi_tphy->base + 0x506c, 0x30000, is_5g ? 0x0 : 0x30000);
> + mtk_phy_update_bits(xfi_tphy->base + 0x5070, 0x670000, is_5g ? 0x620000 : 0x50000);
> + mtk_phy_update_bits(xfi_tphy->base + 0x5074, 0x180000, is_5g ? 0x180000 : 0x0);
> + mtk_phy_update_bits(xfi_tphy->base + 0x5078, 0xf000400, is_5g ? 0x8000000 :
> + 0x7000400);
> + mtk_phy_update_bits(xfi_tphy->base + 0x507c, 0x5000500, is_5g ? 0x4000400 :
> + 0x1000100);
> + mtk_phy_update_bits(xfi_tphy->base + 0x5080, 0x1410, is_1g ? 0x400 : is_5g ? 0x1010 : 0x0);
> + mtk_phy_update_bits(xfi_tphy->base + 0x5084, 0x30300, is_1g ? 0x30300 :
> + is_5g ? 0x30100 :
> + 0x100);
> + mtk_phy_update_bits(xfi_tphy->base + 0x5088, 0x60200, is_1g ? 0x20200 :
> + is_5g ? 0x40000 :
> + 0x20000);
> +
> + /* Setting RXFE adaptation range setting */
> + mtk_phy_update_bits(xfi_tphy->base + 0x50e4, 0xc0000, is_5g ? 0x0 : 0xc0000);
> + mtk_phy_update_bits(xfi_tphy->base + 0x50e8, 0x40000, is_5g ? 0x0 : 0x40000);
> + mtk_phy_update_bits(xfi_tphy->base + 0x50ec, 0xa00, is_1g ? 0x200 : 0x800);
> + mtk_phy_update_bits(xfi_tphy->base + 0x50a8, 0xee0000, is_5g ? 0x800000 :
> + 0x6e0000);
> + mtk_phy_update_bits(xfi_tphy->base + 0x6004, 0x190000, is_5g ? 0x0 : 0x190000);
> +
> + if (is_10g)
> + writel(0x01423342, xfi_tphy->base + 0x00f8);
> + else if (is_5g)
> + writel(0x00a132a1, xfi_tphy->base + 0x00f8);
> + else if (is_2p5g)
> + writel(0x009c329c, xfi_tphy->base + 0x00f8);
> + else
> + writel(0x00fa32fa, xfi_tphy->base + 0x00f8);
> +
> + /* Force SGDT_OUT off and select PCS */
> + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_F4,
> + XFI_DPHY_AD_SGDT_FRC_EN | XFI_DPHY_PCS_SEL,
> + XFI_DPHY_AD_SGDT_FRC_EN |
> + (use_lynxi_pcs ? XFI_DPHY_PCS_SEL_SGMII :
> + XFI_DPHY_PCS_SEL_USXGMII));
> +
> + /* Force GLB_CKDET_OUT */
> + mtk_phy_set_bits(xfi_tphy->base + 0x0030, 0xc00);
> +
> + /* Force AEQ on */
> + writel(XTP_PCS_RX_EQ_IN_PROGRESS(2) | XTP_PCS_PWD_SYNC(2) | XTP_PCS_PWD_ASYNC(2),
> + xfi_tphy->base + REG_DIG_GLB_70);
> +
> + usleep_range(1, 5);
> +
> + /* Setup TX DA default value */
> + mtk_phy_update_bits(xfi_tphy->base + 0x30b0, 0x30, 0x20);
> + writel(0x00008a01, xfi_tphy->base + 0x3028);
> + writel(0x0000a884, xfi_tphy->base + 0x302c);
> + writel(0x00083002, xfi_tphy->base + 0x3024);
> +
> + /* Setup RG default value */
> + if (use_lynxi_pcs) {
> + writel(0x00011110, xfi_tphy->base + 0x3010);
> + writel(0x40704000, xfi_tphy->base + 0x3048);
> + } else {
> + writel(0x00022220, xfi_tphy->base + 0x3010);
> + writel(0x0f020a01, xfi_tphy->base + 0x5064);
> + writel(0x06100600, xfi_tphy->base + 0x50b4);
> + if (interface == PHY_INTERFACE_MODE_USXGMII)
> + writel(0x40704000, xfi_tphy->base + 0x3048);
> + else
> + writel(0x47684100, xfi_tphy->base + 0x3048);
> + }
> +
> + if (is_1g)
> + writel(0x0000c000, xfi_tphy->base + 0x3064);
> +
> + /* Setup RX EQ initial value */
> + mtk_phy_update_bits(xfi_tphy->base + 0x3050, 0xa8000000,
> + (interface != PHY_INTERFACE_MODE_10GBASER) ? 0xa8000000 : 0x0);
> + mtk_phy_update_bits(xfi_tphy->base + 0x3054, 0xaa,
> + (interface != PHY_INTERFACE_MODE_10GBASER) ? 0xaa : 0x0);
> +
> + if (!use_lynxi_pcs)
> + writel(0x00000f00, xfi_tphy->base + 0x306c);
> + else if (is_2p5g)
> + writel(0x22000f00, xfi_tphy->base + 0x306c);
> + else
> + writel(0x20200f00, xfi_tphy->base + 0x306c);
> +
> + mtk_phy_update_bits(xfi_tphy->base + 0xa008, 0x10000, da_war ? 0x10000 : 0x0);
> +
> + mtk_phy_update_bits(xfi_tphy->base + 0xa060, 0x50000, use_lynxi_pcs ? 0x50000 : 0x40000);
> +
> + /* Setup PHYA speed */
> + mtk_phy_update_bits(xfi_tphy->base + REG_ANA_GLB_D0,
> + XTP_GLB_USXGMII_SEL_MASK | XTP_GLB_USXGMII_EN,
> + is_10g ? XTP_GLB_USXGMII_SEL(0) :
> + is_5g ? XTP_GLB_USXGMII_SEL(1) :
> + is_2p5g ? XTP_GLB_USXGMII_SEL(2) :
> + XTP_GLB_USXGMII_SEL(3));
> + mtk_phy_set_bits(xfi_tphy->base + REG_ANA_GLB_D0, XTP_GLB_USXGMII_EN);
> +
> + /* Release reset */
> + mtk_phy_set_bits(xfi_tphy->base + REG_DIG_GLB_70,
> + XTP_PCS_RST_B | XTP_FRC_PCS_RST_B);
> + usleep_range(150, 500);
> +
> + /* Switch to P0 */
> + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_70,
> + XTP_PCS_IN_FR_RG |
> + XTP_FRC_PCS_PWD_ASYNC |
> + XTP_PCS_PWD_ASYNC_MASK |
> + XTP_PCS_PWD_SYNC_MASK |
> + XTP_PCS_UPDT,
> + XTP_PCS_IN_FR_RG |
> + XTP_FRC_PCS_PWD_ASYNC |
> + XTP_PCS_UPDT);
> + usleep_range(1, 5);
> +
> + mtk_phy_clear_bits(xfi_tphy->base + REG_DIG_GLB_70, XTP_PCS_UPDT);
> + usleep_range(15, 50);
> +
> + if (use_lynxi_pcs) {
> + /* Switch to Gen2 */
> + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_70,
> + XTP_PCS_MODE_MASK | XTP_PCS_UPDT,
> + XTP_PCS_MODE(1) | XTP_PCS_UPDT);
> + } else {
> + /* Switch to Gen3 */
> + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_70,
> + XTP_PCS_MODE_MASK | XTP_PCS_UPDT,
> + XTP_PCS_MODE(2) | XTP_PCS_UPDT);
> + }
> + usleep_range(1, 5);
> +
> + mtk_phy_clear_bits(xfi_tphy->base + REG_DIG_GLB_70, XTP_PCS_UPDT);
> +
> + usleep_range(100, 500);
> +
> + /* Enable MAC CK */
> + mtk_phy_set_bits(xfi_tphy->base + REG_DIG_LN_TRX_B0, XTP_LN_TX_MACCK_EN);
> + mtk_phy_clear_bits(xfi_tphy->base + REG_DIG_GLB_F4, XFI_DPHY_AD_SGDT_FRC_EN);
> +
> + /* Enable TX data */
> + mtk_phy_set_bits(xfi_tphy->base + REG_DIG_LN_TRX_40,
> + XTP_LN_FRC_TX_DATA_EN | XTP_LN_TX_DATA_EN);
> + usleep_range(400, 1000);
> +}
> +
> +static int mtk_xfi_tphy_set_mode(struct phy *phy, enum phy_mode mode, int
> + submode)
> +{
> + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy);
> +
> + if (mode != PHY_MODE_ETHERNET)
> + return -EINVAL;
> +
> + switch (submode) {
> + case PHY_INTERFACE_MODE_1000BASEX:
> + case PHY_INTERFACE_MODE_2500BASEX:
> + case PHY_INTERFACE_MODE_SGMII:
> + case PHY_INTERFACE_MODE_5GBASER:
> + case PHY_INTERFACE_MODE_10GBASER:
> + case PHY_INTERFACE_MODE_USXGMII:
> + mtk_xfi_tphy_setup(xfi_tphy, submode);
> + return 0;
> + default:
> + return -EINVAL;
> + }
> +}
> +
> +static int mtk_xfi_tphy_reset(struct phy *phy)
> +{
> + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy);
> +
> + reset_control_assert(xfi_tphy->reset);
> + usleep_range(100, 500);
> + reset_control_deassert(xfi_tphy->reset);
> + usleep_range(1, 10);
> +
> + return 0;
> +}
> +
> +static int mtk_xfi_tphy_power_on(struct phy *phy)
> +{
> + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy);
> +
> + return clk_bulk_prepare_enable(MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks);
> +}
> +
> +static int mtk_xfi_tphy_power_off(struct phy *phy)
> +{
> + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy);
> +
> + clk_bulk_disable_unprepare(MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks);
> +
> + return 0;
> +}
> +
> +static const struct phy_ops mtk_xfi_tphy_ops = {
> + .power_on = mtk_xfi_tphy_power_on,
> + .power_off = mtk_xfi_tphy_power_off,
> + .set_mode = mtk_xfi_tphy_set_mode,
> + .reset = mtk_xfi_tphy_reset,
> + .owner = THIS_MODULE,
> +};
> +
> +static int mtk_xfi_tphy_probe(struct platform_device *pdev)
> +{
> + struct device_node *np = pdev->dev.of_node;
> + struct phy_provider *phy_provider;
> + struct mtk_xfi_tphy *xfi_tphy;
> + struct phy *phy;
> + int ret;
> +
> + if (!np)
> + return -ENODEV;
> +
> + xfi_tphy = devm_kzalloc(&pdev->dev, sizeof(*xfi_tphy), GFP_KERNEL);
> + if (!xfi_tphy)
> + return -ENOMEM;
> +
> + xfi_tphy->base = devm_platform_ioremap_resource(pdev, 0);
> + if (IS_ERR(xfi_tphy->base))
> + return PTR_ERR(xfi_tphy->base);
> +
> + xfi_tphy->dev = &pdev->dev;
> + xfi_tphy->clocks[0].id = "topxtal";
> + xfi_tphy->clocks[1].id = "xfipll";
> + ret = devm_clk_bulk_get(&pdev->dev, MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks);
> + if (ret)
> + return ret;
> +
> + xfi_tphy->reset = devm_reset_control_get_exclusive(&pdev->dev, NULL);
> + if (IS_ERR(xfi_tphy->reset))
> + return PTR_ERR(xfi_tphy->reset);
> +
> + xfi_tphy->da_war = of_property_read_bool(np, "mediatek,usxgmii-performance-errata");
> +
> + phy = devm_phy_create(&pdev->dev, NULL, &mtk_xfi_tphy_ops);
> + if (IS_ERR(phy))
> + return PTR_ERR(phy);
> +
> + phy_set_drvdata(phy, xfi_tphy);
> + phy_provider = devm_of_phy_provider_register(&pdev->dev, of_phy_simple_xlate);
> +
> + return PTR_ERR_OR_ZERO(phy_provider);
> +}
> +
> +static const struct of_device_id mtk_xfi_tphy_match[] = {
> + { .compatible = "mediatek,mt7988-xfi-tphy", },
> + { /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, mtk_xfi_tphy_match);
> +
> +static struct platform_driver mtk_xfi_tphy_driver = {
> + .probe = mtk_xfi_tphy_probe,
> + .driver = {
> + .name = "mtk-xfi-tphy",
> + .of_match_table = mtk_xfi_tphy_match,
> + },
> +};
> +module_platform_driver(mtk_xfi_tphy_driver);
> +
> +MODULE_DESCRIPTION("MediaTek 10GE SerDes XFI T-PHY driver");
> +MODULE_AUTHOR("Daniel Golle <daniel@xxxxxxxxxxxxxx>");
> +MODULE_AUTHOR("Bc-bocun Chen <bc-bocun.chen@xxxxxxxxxxxx>");
> +MODULE_LICENSE("GPL");
> --
> 2.43.0
--
~Vinod
