[PATCH v2 1/3] dt-bindings: arm: bcm: raspberrypi,bcm2835-firmware: Add gpio child node

[Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>]

Unlike the other child nodes of the raspberrypi,bcm2835-firmware device,
the gpio child is documented in a legacy text-based binding in
gpio/raspberrypi,firmware-gpio.txt. This causes DT validation failures:

arch/arm64/boot/dts/broadcom/bcm2711-rpi-4-b.dtb: 'gpio' does not match any of the regexes: 'pinctrl-[0-9]+'
        from schema $id: http://devicetree.org/schemas/arm/bcm/raspberrypi,bcm2835-firmware.yaml#

Convert the binding to YAML and move it to
raspberrypi,bcm2835-firmware.yaml.

Signed-off-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
---
Changes since v1:

- Add minItems for gpio-line-names
---
 .../arm/bcm/raspberrypi,bcm2835-firmware.yaml | 30 +++++++++++++++++++
 .../gpio/raspberrypi,firmware-gpio.txt        | 30 -------------------
 2 files changed, 30 insertions(+), 30 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/gpio/raspberrypi,firmware-gpio.txt

diff --git a/Documentation/devicetree/bindings/arm/bcm/raspberrypi,bcm2835-firmware.yaml b/Documentation/devicetree/bindings/arm/bcm/raspberrypi,bcm2835-firmware.yaml
index 39e3c248f5b7..1f84407a73e4 100644
--- a/Documentation/devicetree/bindings/arm/bcm/raspberrypi,bcm2835-firmware.yaml
+++ b/Documentation/devicetree/bindings/arm/bcm/raspberrypi,bcm2835-firmware.yaml
@@ -46,6 +46,30 @@ properties:
       - compatible
       - "#clock-cells"
 
+  gpio:
+    type: object
+    additionalProperties: false
+
+    properties:
+      compatible:
+        const: raspberrypi,firmware-gpio
+
+      gpio-controller: true
+
+      "#gpio-cells":
+        const: 2
+        description:
+          The first cell is the pin number, and the second cell is used to
+          specify the gpio polarity (GPIO_ACTIVE_HIGH or GPIO_ACTIVE_LOW).
+
+      gpio-line-names:
+        minItems: 8
+
+    required:
+      - compatible
+      - gpio-controller
+      - "#gpio-cells"
+
   reset:
     type: object
     additionalProperties: false
@@ -96,6 +120,12 @@ examples:
             #clock-cells = <1>;
         };
 
+        expgpio: gpio {
+            compatible = "raspberrypi,firmware-gpio";
+            gpio-controller;
+            #gpio-cells = <2>;
+        };
+
         reset: reset {
             compatible = "raspberrypi,firmware-reset";
             #reset-cells = <1>;
diff --git a/Documentation/devicetree/bindings/gpio/raspberrypi,firmware-gpio.txt b/Documentation/devicetree/bindings/gpio/raspberrypi,firmware-gpio.txt
deleted file mode 100644
index ce97265e23ba..000000000000
--- a/Documentation/devicetree/bindings/gpio/raspberrypi,firmware-gpio.txt
+++ /dev/null
@@ -1,30 +0,0 @@
-Raspberry Pi GPIO expander
-
-The Raspberry Pi 3 GPIO expander is controlled by the VC4 firmware. The
-firmware exposes a mailbox interface that allows the ARM core to control the
-GPIO lines on the expander.
-
-The Raspberry Pi GPIO expander node must be a child node of the Raspberry Pi
-firmware node.
-
-Required properties:
-
-- compatible : Should be "raspberrypi,firmware-gpio"
-- gpio-controller : Marks the device node as a gpio controller
-- #gpio-cells : Should be two.  The first cell is the pin number, and
-  the second cell is used to specify the gpio polarity:
-  0 = active high
-  1 = active low
-
-Example:
-
-firmware: firmware-rpi {
-	compatible = "raspberrypi,bcm2835-firmware";
-	mboxes = <&mailbox>;
-
-	expgpio: gpio {
-		 compatible = "raspberrypi,firmware-gpio";
-		 gpio-controller;
-		 #gpio-cells = <2>;
-	 };
-};
-- 
Regards,

Laurent Pinchart