Convert text to yaml for atmel nand controller Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@xxxxxxxxxxxxx> --- .../devicetree/bindings/mtd/atmel-nand.txt | 50 ------- .../devicetree/bindings/mtd/atmel-nand.yaml | 166 +++++++++++++++++++++ MAINTAINERS | 2 +- 3 files changed, 167 insertions(+), 51 deletions(-) diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt index 4598930851d9..e332515c499a 100644 --- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -1,53 +1,3 @@ -Atmel NAND flash controller bindings - -The NAND flash controller node should be defined under the EBI bus (see -Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt). -One or several NAND devices can be defined under this NAND controller. -The NAND controller might be connected to an ECC engine. - -* NAND controller bindings: - -Required properties: -- compatible: should be one of the following - "atmel,at91rm9200-nand-controller" - "atmel,at91sam9260-nand-controller" - "atmel,at91sam9261-nand-controller" - "atmel,at91sam9g45-nand-controller" - "atmel,sama5d3-nand-controller" - "microchip,sam9x60-nand-controller" -- ranges: empty ranges property to forward EBI ranges definitions. -- #address-cells: should be set to 2. -- #size-cells: should be set to 1. -- atmel,nfc-io: phandle to the NFC IO block. Only required for sama5d3 - controllers. -- atmel,nfc-sram: phandle to the NFC SRAM block. Only required for sama5d3 - controllers. - -Optional properties: -- ecc-engine: phandle to the PMECC block. Only meaningful if the SoC embeds - a PMECC engine. - -* NAND device/chip bindings: - -Required properties: -- reg: describes the CS lines assigned to the NAND device. If the NAND device - exposes multiple CS lines (multi-dies chips), your reg property will - contain X tuples of 3 entries. - 1st entry: the CS line this NAND chip is connected to - 2nd entry: the base offset of the memory region assigned to this - device (always 0) - 3rd entry: the memory region size (always 0x800000) - -Optional properties: -- rb-gpios: the GPIO(s) used to check the Ready/Busy status of the NAND. -- cs-gpios: the GPIO(s) used to control the CS line. -- det-gpios: the GPIO used to detect if a Smartmedia Card is present. -- atmel,rb: an integer identifying the native Ready/Busy pin. Only meaningful - on sama5 SoCs. - -All generic properties are described in the generic yaml files under -Documentation/devicetree/bindings/mtd/. - * ECC engine (PMECC) bindings: Required properties: diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.yaml b/Documentation/devicetree/bindings/mtd/atmel-nand.yaml new file mode 100644 index 000000000000..a5482d292293 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.yaml @@ -0,0 +1,166 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/atmel-nand.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Atmel NAND flash controller + +maintainers: + - Balamanikandan Gunasundar <balamanikandan.gunasundar@xxxxxxxxxxxxx> + +description: | + The NAND flash controller node should be defined under the EBI bus (see + Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt|yaml). + One or several NAND devices can be defined under this NAND controller. + The NAND controller might be connected to an ECC engine. + +properties: + compatible: + oneOf: + - items: + - enum: + - atmel,at91rm9200-nand-controller + - atmel,at91sam9260-nand-controller + - atmel,at91sam9261-nand-controller + - atmel,at91sam9g45-nand-controller + - atmel,sama5d3-nand-controller + - microchip,sam9x60-nand-controller + + ranges: + description: empty ranges property to forward EBI ranges definitions. + + ecc-engine: + description: + phandle to the PMECC block. Only meaningful if the SoC embeds a PMECC + engine. + +allOf: + - if: + properties: + compatible: + contains: + enum: + - atmel,at91rm9200-nand-controller + - atmel,at91sam9260-nand-controller + - atmel,at91sam9261-nand-controller + - atmel,at91sam9g45-nand-controller + - atmel,sama5d3-nand-controller + - microchip,sam9x60-nand-controller + then: + properties: + "#address-cells": + const: 2 + + "#size-cells": + const: 1 + + - if: + properties: + compatible: + contains: + const: atmel,sama5d3-nand-controller + then: + properties: + atmel,nfc-io: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to the NFC IO block. + + atmel,nfc-sram: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to the NFC SRAM block + +required: + - compatible + - ranges + - "#address-cells" + - "#size-cells" + +patternProperties: + "^nand@[a-f0-9]$": + type: object + $ref: nand-chip.yaml# + description: + NAND chip bindings. All generic properties described in + Documentation/devicetree/bindings/mtd/{common,nand}.txt also apply to + the NAND device node, and NAND partitions should be defined under the + NAND node as described in + Documentation/devicetree/bindings/mtd/partition.txt. + + properties: + reg: + minItems: 1 + description: + describes the CS lines assigned to the NAND device. If the NAND device + exposes multiple CS lines (multi-dies chips), your reg property will + contain X tuples of 3 entries. + reg = <0x3 0x0 0x800000>; + 1st entry - the CS line this NAND chip is connected to + 2nd entry - the base offset of the memory region assigned to this + device (always 0) + 3rd entry - the memory region size (always 0x800000) + + rb-gpios: + description: + the GPIO(s) used to check the Ready/Busy status of the NAND. + + cs-gpios: + description: + the GPIO(s) used to control the CS line. + + det-gpios: + description: + the GPIO used to detect if a Smartmedia Card is present. + + "atmel,rb": + description: + an integer identifying the native Ready/Busy pin. Only meaningful + on sama5 SoCs. + $ref: /schemas/types.yaml#/definitions/uint32 + +unevaluatedProperties: false + +examples: + - | + nfc_io: nfc-io@70000000 { + compatible = "atmel,sama5d3-nfc-io", "syscon"; + reg = <0x70000000 0x8000000>; + }; + + pmecc: ecc-engine@ffffc070 { + compatible = "atmel,at91sam9g45-pmecc"; + reg = <0xffffc070 0x490>, + <0xffffc500 0x100>; + }; + + ebi: ebi@10000000 { + compatible = "atmel,sama5d3-ebi"; + #address-cells = <2>; + #size-cells = <1>; + atmel,smc = <&hsmc>; + reg = <0x10000000 0x10000000 + 0x40000000 0x30000000>; + ranges = <0x0 0x0 0x10000000 0x10000000 + 0x1 0x0 0x40000000 0x10000000 + 0x2 0x0 0x50000000 0x10000000 + 0x3 0x0 0x60000000 0x10000000>; + clocks = <&mck>; + + nandflash_controller: nandflash-controller { + compatible = "atmel,sama5d3-nand-controller"; + ecc-engine = <&pmecc>; + #address-cells = <2>; + #size-cells = <1>; + ranges; + + nand@3 { + reg = <0x3 0x0 0x800000>; + atmel,rb = <0>; + + /* + * Put generic NAND/MTD properties and + * subnodes here. + */ + }; + }; + }; diff --git a/MAINTAINERS b/MAINTAINERS index b6582bd3eb2c..3f2a6756223f 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -14503,7 +14503,7 @@ MICROCHIP NAND DRIVER M: Balamanikandan Gunasundar <balamanikandan.gunasundar@xxxxxxxxxxxxx> L: linux-mtd@xxxxxxxxxxxxxxxxxxx S: Supported -F: Documentation/devicetree/bindings/mtd/atmel-nand.txt +F: Documentation/devicetree/bindings/mtd/atmel-*.yaml F: drivers/mtd/nand/raw/atmel/* MICROCHIP OTPC DRIVER -- 2.25.1
