On Fri, 15 Mar 2024 11:37:04 +0530, Sumit Garg wrote: > Add Schneider Electric HMIBSC board DTS. The HMIBSC board is an IIoT Edge > Box Core board based on the Qualcomm APQ8016E SoC. For more information > refer to the product page [1]. > > One of the major difference from db410c is serial port where HMIBSC board > uses UART1 as the debug console with a default RS232 mode (UART1 mode mux > configured via gpio99 and gpio100). > > Support for Schneider Electric HMIBSC. Features: > - Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306) > - 1GiB RAM > - 8GiB eMMC, SD slot > - WiFi and Bluetooth > - 2x Host, 1x Device USB port > - HDMI > - Discrete TPM2 chip over SPI > - USB ethernet adaptors (soldered) > > This series is a v2 since v1 of this DTS file has been reviewed on the > U-Boot mailing list [2]. > > Changes in v3: > - Picked up tags. > - Fixed further DT schema warnings. > - Configure resin/power button interrupt as falling edge. > - Incorporate DTS coding style comments from Krzysztof and Konrad. > > Changes in v2: > - Fix DT schema warnings. > - Incorporate suggestions from Stephan. > - Document UART1 mode GPIOs based mux. > > [1] https://www.se.com/us/en/product/HMIBSCEA53D1L0T/iiot-edge-box-core-harmony-ipc-emmc-dc-linux-tpm/ > [2] https://patchwork.ozlabs.org/project/uboot/patch/20240311111027.44577-6-sumit.garg@xxxxxxxxxx/ > > Sumit Garg (3): > dt-bindings: vendor-prefixes: Add Schneider Electric > dt-bindings: arm: qcom: Add Schneider Electric HMIBSC board > arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS > > .../devicetree/bindings/arm/qcom.yaml | 1 + > .../devicetree/bindings/vendor-prefixes.yaml | 2 + > arch/arm64/boot/dts/qcom/Makefile | 1 + > .../dts/qcom/apq8016-schneider-hmibsc.dts | 510 ++++++++++++++++++ > 4 files changed, 514 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts > > -- > 2.34.1 > > > My bot found new DTB warnings on the .dts files added or changed in this series. Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings are fixed by another series. Ultimately, it is up to the platform maintainer whether these warnings are acceptable or not. No need to reply unless the platform maintainer has comments. If you already ran DT checks and didn't see these error(s), then make sure dt-schema is up to date: pip3 install dtschema --upgrade New warnings running 'make CHECK_DTBS=y qcom/apq8016-schneider-hmibsc.dtb' for 20240315060707.471248-1-sumit.garg@xxxxxxxxxx: arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dtb: /soc@0/audio-codec@771c000: failed to match any schema with compatible: ['qcom,msm8916-wcd-digital-codec'] arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dtb: /soc@0/power-manager@b088000: failed to match any schema with compatible: ['qcom,msm8916-acc'] arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dtb: /soc@0/power-manager@b098000: failed to match any schema with compatible: ['qcom,msm8916-acc'] arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dtb: /soc@0/power-manager@b0a8000: failed to match any schema with compatible: ['qcom,msm8916-acc'] arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dtb: /soc@0/power-manager@b0b8000: failed to match any schema with compatible: ['qcom,msm8916-acc'] arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dtb: /usb-id: failed to match any schema with compatible: ['linux,extcon-usb-gpio']
