On Thu, 7 Mar 2024 at 08:28, Dmitry Baryshkov
<dmitry.baryshkov@xxxxxxxxxx> wrote:
>
> On Wed, 6 Mar 2024 at 22:35, Robert Marko <robimarko@xxxxxxxxx> wrote:
> >
> >
> > On 06. 03. 2024. 20:43, Dmitry Baryshkov wrote:
> > > On Wed, 6 Mar 2024 at 14:31, Chukun Pan <amadeus@xxxxxxxxxx> wrote:
> > >> Add node to support mmc controller inside of IPQ6018.
> > >> This controller supports both eMMC and SD cards.
> > >>
> > >> Tested with:
> > >> eMMC (HS200)
> > >> SD Card (SDR50/SDR104)
> > >>
> > >> Signed-off-by: Chukun Pan <amadeus@xxxxxxxxxx>
> > >> ---
> > >> arch/arm64/boot/dts/qcom/ipq6018.dtsi | 19 +++++++++++++++++++
> > >> 1 file changed, 19 insertions(+)
> > >>
> > >> diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
> > >> index 322eced0b876..420c192bccd9 100644
> > >> --- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
> > >> +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
> > >> @@ -441,6 +441,25 @@ dwc_1: usb@7000000 {
> > >> };
> > >> };
> > >>
> > >> + sdhc: mmc@7804000 {
> > >> + compatible = "qcom,ipq6018-sdhci", "qcom,sdhci-msm-v5";
> > >> + reg = <0x0 0x07804000 0x0 0x1000>,
> > >> + <0x0 0x07805000 0x0 0x1000>;
> > >> + reg-names = "hc", "cqhci";
> > >> +
> > >> + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> > >> + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
> > >> + interrupt-names = "hc_irq", "pwr_irq";
> > >> +
> > >> + clocks = <&gcc GCC_SDCC1_AHB_CLK>,
> > >> + <&gcc GCC_SDCC1_APPS_CLK>,
> > >> + <&xo>;
> > >> + clock-names = "iface", "core", "xo";
> > >> + resets = <&gcc GCC_SDCC1_BCR>;
> > >> + max-frequency = <192000000>;
> > > If I understand correctly, GCC_SDCC1_APPS_CLK support frequencies up
> > > to 384 MHz, but here you are limiting it to 192 MHz. Why is it so?
> > >
> > > I am not sure that 384MHz is actually supported as IPQ6018 datasheet
> > > clearly indicates that HS400 mode is not supported.
>
> I didn't check the datasheet, I opened the gcc-ipq6018.c
I understand that, I just pointed it out, it wouldn't surprise me if
the frequency table
was just copy/pasted from IPQ8074.
Regards,
Robert
>
> > >
> > > Regards,
> > > Robert
> > >
> > >> + status = "disabled";
> > >> + };
> > >> +
> > >> blsp_dma: dma-controller@7884000 {
> > >> compatible = "qcom,bam-v1.7.0";
> > >> reg = <0x0 0x07884000 0x0 0x2b000>;
> > >> --
> > >> 2.25.1
> > >>
> > >>
> > >
>
>
>
> --
> With best wishes
> Dmitry
