Everything in i2c.txt is covered by schemas/i2c/i2c-controller.yaml in
dtschema project, so remove i2c.txt and update links to it in the tree.
Signed-off-by: Rob Herring <robh@xxxxxxxxxx>
---
Wolfram, you can take it or I can.
.../bindings/gpio/gateworks,pld-gpio.txt | 3 +-
Documentation/devicetree/bindings/i2c/i2c.txt | 151 ------------------
.../i2c/nvidia,tegra186-bpmp-i2c.yaml | 3 +-
.../devicetree/bindings/i3c/i3c.yaml | 2 +-
.../devicetree/bindings/sound/cs4341.txt | 2 +-
MAINTAINERS | 1 -
6 files changed, 4 insertions(+), 158 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/i2c/i2c.txt
diff --git a/Documentation/devicetree/bindings/gpio/gateworks,pld-gpio.txt b/Documentation/devicetree/bindings/gpio/gateworks,pld-gpio.txt
index 6e81f8b755c5..d543fd1b8b23 100644
--- a/Documentation/devicetree/bindings/gpio/gateworks,pld-gpio.txt
+++ b/Documentation/devicetree/bindings/gpio/gateworks,pld-gpio.txt
@@ -1,7 +1,6 @@
Gateworks PLD GPIO controller bindings
-The GPIO controller should be a child node on an I2C bus,
-see: i2c/i2c.txt for details.
+The GPIO controller should be a child node on an I2C bus.
Required properties:
- compatible: Should be "gateworks,pld-gpio"
diff --git a/Documentation/devicetree/bindings/i2c/i2c.txt b/Documentation/devicetree/bindings/i2c/i2c.txt
deleted file mode 100644
index fc3dd7ec0445..000000000000
--- a/Documentation/devicetree/bindings/i2c/i2c.txt
+++ /dev/null
@@ -1,151 +0,0 @@
-Generic device tree bindings for I2C busses
-===========================================
-
-This document describes generic bindings which can be used to describe I2C
-busses and their child devices in a device tree.
-
-Required properties (per bus)
------------------------------
-
-- #address-cells - should be <1>. Read more about addresses below.
-- #size-cells - should be <0>.
-- compatible - name of I2C bus controller
-
-For other required properties e.g. to describe register sets,
-clocks, etc. check the binding documentation of the specific driver.
-
-The cells properties above define that an address of children of an I2C bus
-are described by a single value.
-
-Optional properties (per bus)
------------------------------
-
-These properties may not be supported by all drivers. However, if a driver
-wants to support one of the below features, it should adapt these bindings.
-
-- clock-frequency
- frequency of bus clock in Hz.
-
-- i2c-bus
- For I2C adapters that have child nodes that are a mixture of both I2C
- devices and non-I2C devices, the 'i2c-bus' subnode can be used for
- populating I2C devices. If the 'i2c-bus' subnode is present, only
- subnodes of this will be considered as I2C slaves. The properties,
- '#address-cells' and '#size-cells' must be defined under this subnode
- if present.
-
-- i2c-scl-falling-time-ns
- Number of nanoseconds the SCL signal takes to fall; t(f) in the I2C
- specification.
-
-- i2c-scl-internal-delay-ns
- Number of nanoseconds the IP core additionally needs to setup SCL.
-
-- i2c-scl-rising-time-ns
- Number of nanoseconds the SCL signal takes to rise; t(r) in the I2C
- specification.
-
-- i2c-sda-falling-time-ns
- Number of nanoseconds the SDA signal takes to fall; t(f) in the I2C
- specification.
-
-- i2c-analog-filter
- Enable analog filter for i2c lines.
-
-- i2c-digital-filter
- Enable digital filter for i2c lines.
-
-- i2c-digital-filter-width-ns
- Width of spikes which can be filtered by digital filter
- (i2c-digital-filter). This width is specified in nanoseconds.
-
-- i2c-analog-filter-cutoff-frequency
- Frequency that the analog filter (i2c-analog-filter) uses to distinguish
- which signal to filter. Signal with higher frequency than specified will
- be filtered out. Only lower frequency will pass (this is applicable to
- a low-pass analog filter). Typical value should be above the normal
- i2c bus clock frequency (clock-frequency).
- Specified in Hz.
-
-- multi-master
- states that there is another master active on this bus. The OS can use
- this information to adapt power management to keep the arbitration awake
- all the time, for example. Can not be combined with 'single-master'.
-
-- pinctrl
- add extra pinctrl to configure SCL/SDA pins to GPIO function for bus
- recovery, call it "gpio" or "recovery" (deprecated) state
-
-- scl-gpios
- specify the gpio related to SCL pin. Used for GPIO bus recovery.
-
-- sda-gpios
- specify the gpio related to SDA pin. Optional for GPIO bus recovery.
-
-- single-master
- states that there is no other master active on this bus. The OS can use
- this information to detect a stalled bus more reliably, for example.
- Can not be combined with 'multi-master'.
-
-- smbus
- states that additional SMBus restrictions and features apply to this bus.
- An example of feature is SMBusHostNotify. Examples of restrictions are
- more reserved addresses and timeout definitions.
-
-- smbus-alert
- states that the optional SMBus-Alert feature apply to this bus.
-
-- mctp-controller
- indicates that the system is accessible via this bus as an endpoint for
- MCTP over I2C transport.
-
-Required properties (per child device)
---------------------------------------
-
-- compatible
- name of I2C slave device
-
-- reg
- One or many I2C slave addresses. These are usually a 7 bit addresses.
- However, flags can be attached to an address. I2C_TEN_BIT_ADDRESS is
- used to mark a 10 bit address. It is needed to avoid the ambiguity
- between e.g. a 7 bit address of 0x50 and a 10 bit address of 0x050
- which, in theory, can be on the same bus.
- Another flag is I2C_OWN_SLAVE_ADDRESS to mark addresses on which we
- listen to be devices ourselves.
-
-Optional properties (per child device)
---------------------------------------
-
-These properties may not be supported by all drivers. However, if a driver
-wants to support one of the below features, it should adapt these bindings.
-
-- host-notify
- device uses SMBus host notify protocol instead of interrupt line.
-
-- interrupts
- interrupts used by the device.
-
-- interrupt-names
- "irq", "wakeup" and "smbus_alert" names are recognized by I2C core,
- other names are left to individual drivers.
-
-- reg-names
- Names of map programmable addresses.
- It can contain any map needing another address than default one.
-
-- wakeup-source
- device can be used as a wakeup source.
-
-Binding may contain optional "interrupts" property, describing interrupts
-used by the device. I2C core will assign "irq" interrupt (or the very first
-interrupt if not using interrupt names) as primary interrupt for the slave.
-
-Alternatively, devices supporting SMBus Host Notify, and connected to
-adapters that support this feature, may use "host-notify" property. I2C
-core will create a virtual interrupt for Host Notify and assign it as
-primary interrupt for the slave.
-
-Also, if device is marked as a wakeup source, I2C core will set up "wakeup"
-interrupt for the device. If "wakeup" interrupt name is not present in the
-binding, then primary interrupt will be used as wakeup interrupt.
diff --git a/Documentation/devicetree/bindings/i2c/nvidia,tegra186-bpmp-i2c.yaml b/Documentation/devicetree/bindings/i2c/nvidia,tegra186-bpmp-i2c.yaml
index b8319dcf3d8a..8676335e9e94 100644
--- a/Documentation/devicetree/bindings/i2c/nvidia,tegra186-bpmp-i2c.yaml
+++ b/Documentation/devicetree/bindings/i2c/nvidia,tegra186-bpmp-i2c.yaml
@@ -21,8 +21,7 @@ description: |
See ../firmware/nvidia,tegra186-bpmp.yaml for details of the BPMP
binding.
- This node represents an I2C controller. See ../i2c/i2c.txt for details
- of the core I2C binding.
+ This node represents an I2C controller.
properties:
compatible:
diff --git a/Documentation/devicetree/bindings/i3c/i3c.yaml b/Documentation/devicetree/bindings/i3c/i3c.yaml
index c816e295d565..87cadbcdc61c 100644
--- a/Documentation/devicetree/bindings/i3c/i3c.yaml
+++ b/Documentation/devicetree/bindings/i3c/i3c.yaml
@@ -71,7 +71,7 @@ patternProperties:
description: |
I2C child, should be named: <device-type>@<i2c-address>
- All properties described in Documentation/devicetree/bindings/i2c/i2c.txt
+ All properties described in dtschema schemas/i2c/i2c-controller.yaml
are valid here, except the reg property whose content is changed.
properties:
diff --git a/Documentation/devicetree/bindings/sound/cs4341.txt b/Documentation/devicetree/bindings/sound/cs4341.txt
index 12b4aa8ef0db..c1d5c8ad1a36 100644
--- a/Documentation/devicetree/bindings/sound/cs4341.txt
+++ b/Documentation/devicetree/bindings/sound/cs4341.txt
@@ -9,7 +9,7 @@ Required properties:
number for SPI.
For required properties on I2C-bus, please consult
-Documentation/devicetree/bindings/i2c/i2c.txt
+dtschema schemas/i2c/i2c-controller.yaml
For required properties on SPI-bus, please consult
Documentation/devicetree/bindings/spi/spi-bus.txt
diff --git a/MAINTAINERS b/MAINTAINERS
index 45c6c13b4edf..50a906eb8dfd 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -10074,7 +10074,6 @@ S: Maintained
W: https://i2c.wiki.kernel.org/
Q: https://patchwork.ozlabs.org/project/linux-i2c/list/
T: git git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux.git
-F: Documentation/devicetree/bindings/i2c/i2c.txt
F: Documentation/i2c/
F: drivers/i2c/*
F: include/dt-bindings/i2c/i2c.h
--
2.43.0
