Am Donnerstag, 29. Januar 2015, 10:20:22 schrieb Andrey Danin:
> NVEC driver was reimplemented to use tegra i2c. Use common i2c bindings
> for NVEC node.
>
> Signed-off-by: Andrey Danin <danindrey@xxxxxxx>
> ---
> .../devicetree/bindings/nvec/nvidia,nvec.txt | 19 ++-----------------
> arch/arm/boot/dts/tegra20-paz00.dts | 22
> +++++++++------------- 2 files changed, 11 insertions(+), 30 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/nvec/nvidia,nvec.txt
> b/Documentation/devicetree/bindings/nvec/nvidia,nvec.txt index
> 5ae601e..d82c125 100644
> --- a/Documentation/devicetree/bindings/nvec/nvidia,nvec.txt
> +++ b/Documentation/devicetree/bindings/nvec/nvidia,nvec.txt
> @@ -2,20 +2,5 @@ NVIDIA compliant embedded controller
>
> Required properties:
> - compatible : should be "nvidia,nvec".
based on the earlier discussion with Wolfram, this should be "nvidia,nvec-
slave" to distunguish it from a possible nvec master driver.
> -- reg : the iomem of the i2c slave controller
> -- interrupts : the interrupt line of the i2c slave controller
> -- clock-frequency : the frequency of the i2c bus
> -- gpios : the gpio used for ec request
> -- slave-addr: the i2c address of the slave controller
> -- clocks : Must contain an entry for each entry in clock-names.
> - See ../clocks/clock-bindings.txt for details.
> -- clock-names : Must include the following entries:
> - Tegra20/Tegra30:
> - - div-clk
> - - fast-clk
> - Tegra114:
> - - div-clk
> -- resets : Must contain an entry for each entry in reset-names.
> - See ../reset/reset.txt for details.
> -- reset-names : Must include the following entries:
> - - i2c
> +- request-gpios : the gpio used for ec request
> +- reg: the i2c address of the slave controller
> diff --git a/arch/arm/boot/dts/tegra20-paz00.dts
> b/arch/arm/boot/dts/tegra20-paz00.dts index ed7e100..65e247b 100644
> --- a/arch/arm/boot/dts/tegra20-paz00.dts
> +++ b/arch/arm/boot/dts/tegra20-paz00.dts
> @@ -288,20 +288,16 @@
> clock-frequency = <100000>;
> };
>
> - nvec@7000c500 {
> - compatible = "nvidia,nvec";
> - reg = <0x7000c500 0x100>;
> - interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> + i2c@7000c500 {
> + status = "okay";
> clock-frequency = <80000>;
> - request-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
> - slave-addr = <138>;
> - clocks = <&tegra_car TEGRA20_CLK_I2C3>,
> - <&tegra_car TEGRA20_CLK_PLL_P_OUT3>;
> - clock-names = "div-clk", "fast-clk";
> - resets = <&tegra_car 67>;
> - reset-names = "i2c";
> +
> + nvec: nvec@45 {
> + compatible = "nvidia,nvec";
> + request-gpios = <&gpio TEGRA_GPIO(V, 2)
> + GPIO_ACTIVE_HIGH>;
> + reg = <0x45>;
> + };
> };
>
> i2c@7000d000 {
Attachment:
signature.asc
Description: This is a digitally signed message part.
