[PATCH v2] dt-bindings: interrupt-controller: Convert Atmel AIC to json-schema

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Convert the Atmel AIC binding document to DT schema format using
json-schema.

Signed-off-by: Dharma Balasubiramani <dharma.b@xxxxxxxxxxxxx>
---
Changelog
v1 -> v2
- Drop the '|' as there is no formatting to preserve.
- Remove unnecessary marketing statement from description.
- Drop the description for interrupts and reg, it's obvious.
- Put reg after compatible.
- Drop comment in example.
- Drop the example of device that is wired to an AIC as it's(dma) binding is
  not yet available.
---
 .../interrupt-controller/atmel,aic.txt        | 43 -----------
 .../interrupt-controller/atmel,aic.yaml       | 74 +++++++++++++++++++
 2 files changed, 74 insertions(+), 43 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/interrupt-controller/atmel,aic.txt
 create mode 100644 Documentation/devicetree/bindings/interrupt-controller/atmel,aic.yaml

diff --git a/Documentation/devicetree/bindings/interrupt-controller/atmel,aic.txt b/Documentation/devicetree/bindings/interrupt-controller/atmel,aic.txt
deleted file mode 100644
index 7079d44bf3ba..000000000000
--- a/Documentation/devicetree/bindings/interrupt-controller/atmel,aic.txt
+++ /dev/null
@@ -1,43 +0,0 @@
-* Advanced Interrupt Controller (AIC)
-
-Required properties:
-- compatible: Should be:
-    - "atmel,<chip>-aic" where  <chip> can be "at91rm9200", "sama5d2",
-      "sama5d3" or "sama5d4"
-    - "microchip,<chip>-aic" where <chip> can be "sam9x60"
-
-- interrupt-controller: Identifies the node as an interrupt controller.
-- #interrupt-cells: The number of cells to define the interrupts. It should be 3.
-  The first cell is the IRQ number (aka "Peripheral IDentifier" on datasheet).
-  The second cell is used to specify flags:
-    bits[3:0] trigger type and level flags:
-      1 = low-to-high edge triggered.
-      2 = high-to-low edge triggered.
-      4 = active high level-sensitive.
-      8 = active low level-sensitive.
-      Valid combinations are 1, 2, 3, 4, 8.
-      Default flag for internal sources should be set to 4 (active high).
-  The third cell is used to specify the irq priority from 0 (lowest) to 7
-  (highest).
-- reg: Should contain AIC registers location and length
-- atmel,external-irqs: u32 array of external irqs.
-
-Examples:
-	/*
-	 * AIC
-	 */
-	aic: interrupt-controller@fffff000 {
-		compatible = "atmel,at91rm9200-aic";
-		interrupt-controller;
-		#interrupt-cells = <3>;
-		reg = <0xfffff000 0x200>;
-	};
-
-	/*
-	 * An interrupt generating device that is wired to an AIC.
-	 */
-	dma: dma-controller@ffffec00 {
-		compatible = "atmel,at91sam9g45-dma";
-		reg = <0xffffec00 0x200>;
-		interrupts = <21 4 5>;
-	};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/atmel,aic.yaml b/Documentation/devicetree/bindings/interrupt-controller/atmel,aic.yaml
new file mode 100644
index 000000000000..df81115a8b7f
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/atmel,aic.yaml
@@ -0,0 +1,74 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/interrupt-controller/atmel,aic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Advanced Interrupt Controller (AIC)
+
+maintainers:
+  - Nicolas Ferre <nicolas.ferre@xxxxxxxxxxxxx>
+  - Dharma balasubiramani <dharma.b@xxxxxxxxxxxxx>
+
+description:
+  The Advanced Interrupt Controller (AIC) is an 8-level priority, individually
+  maskable, vectored interrupt controller providing handling of up to one
+  hundred and twenty-eight interrupt sources.
+
+allOf:
+  - $ref: /schemas/interrupt-controller.yaml#
+
+properties:
+  compatible:
+    enum:
+      - atmel,at91rm9200-aic
+      - atmel,sama5d2-aic
+      - atmel,sama5d3-aic
+      - atmel,sama5d4-aic
+      - microchip,sam9x60-aic
+
+  reg:
+    maxItems: 1
+
+  interrupt-controller: true
+
+  "#interrupt-cells":
+    const: 3
+    description: |
+      The 1st cell is the IRQ number (Peripheral IDentifier on datasheet).
+      The 2nd cell specifies flags:
+        bits[3:0] trigger type and level flags:
+          1 = low-to-high edge triggered.
+          2 = high-to-low edge triggered.
+          4 = active high level-sensitive.
+          8 = active low level-sensitive.
+        Valid combinations: 1, 2, 3, 4, 8.
+        Default for internal sources: 4 (active high).
+      The 3rd cell specifies irq priority from 0 (lowest) to 7 (highest).
+
+  interrupts:
+    maxItems: 1
+
+  atmel,external-irqs:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    description: u32 array of external irqs.
+
+required:
+  - compatible
+  - reg
+  - interrupt-controller
+  - "#interrupt-cells"
+  - atmel,external-irqs
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    interrupt-controller@fffff000 {
+      compatible = "atmel,at91rm9200-aic";
+      interrupt-controller;
+      #interrupt-cells = <3>;
+      reg = <0xfffff000 0x200>;
+      atmel,external-irqs = <31>;
+    };
+...

base-commit: 0dd3ee31125508cd67f7e7172247f05b7fd1753a
-- 
2.25.1





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux