WKUP_PADCONFIG registers for wakeup and mcu uart lies under wkup_pmx2 for J7200. Thus, modify pinmux for both of them. Signed-off-by: Bhavya Kapoor <b-kapoor@xxxxxx> --- .../boot/dts/ti/k3-j7200-common-proc-board.dts | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-) diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts index 1d8bddcae90e..6593c5da82c0 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts @@ -119,24 +119,25 @@ transceiver3: can-phy3 { }; &wkup_pmx0 { +}; + +&wkup_pmx2 { mcu_uart0_pins_default: mcu-uart0-default-pins { pinctrl-single,pins = < - J721E_WKUP_IOPAD(0xf4, PIN_INPUT, 0) /* (D20) MCU_UART0_RXD */ - J721E_WKUP_IOPAD(0xf0, PIN_OUTPUT, 0) /* (D19) MCU_UART0_TXD */ - J721E_WKUP_IOPAD(0xf8, PIN_INPUT, 0) /* (E20) MCU_UART0_CTSn */ - J721E_WKUP_IOPAD(0xfc, PIN_OUTPUT, 0) /* (E21) MCU_UART0_RTSn */ + J721E_WKUP_IOPAD(0x90, PIN_INPUT, 0) /* (E20) MCU_UART0_CTSn */ + J721E_WKUP_IOPAD(0x94, PIN_OUTPUT, 0) /* (E21) MCU_UART0_RTSn */ + J721E_WKUP_IOPAD(0x8c, PIN_INPUT, 0) /* (D20) MCU_UART0_RXD */ + J721E_WKUP_IOPAD(0x88, PIN_OUTPUT, 0) /* (D19) MCU_UART0_TXD */ >; }; wkup_uart0_pins_default: wkup-uart0-default-pins { pinctrl-single,pins = < - J721E_WKUP_IOPAD(0xb0, PIN_INPUT, 0) /* (B14) WKUP_UART0_RXD */ - J721E_WKUP_IOPAD(0xb4, PIN_OUTPUT, 0) /* (A14) WKUP_UART0_TXD */ + J721E_WKUP_IOPAD(0x48, PIN_INPUT, 0) /* (B14) WKUP_UART0_RXD */ + J721E_WKUP_IOPAD(0x4c, PIN_OUTPUT, 0) /* (A14) WKUP_UART0_TXD */ >; }; -}; -&wkup_pmx2 { mcu_cpsw_pins_default: mcu-cpsw-default-pins { pinctrl-single,pins = < J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */ @@ -272,7 +273,6 @@ &mcu_uart0 { status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&mcu_uart0_pins_default>; - clock-frequency = <96000000>; }; &main_uart0 { -- 2.34.1