Hi Miquèl,
On Thu, Jan 25, 2024 at 10:19 PM Miquel Raynal
<miquel.raynal@xxxxxxxxxxx> wrote:
>
> Hi David,
>
> dregan@xxxxxxxxxxxx wrote on Thu, 25 Jan 2024 11:47:46 -0800:
>
> > Hi Miquèl,
> >
> > On Wed, Jan 24, 2024 at 9:40 AM Miquel Raynal <miquel.raynal@xxxxxxxxxxx> wrote:
> > >
> > > Hi David,
> > >
> > > dregan@xxxxxxxxxxxx wrote on Tue, 23 Jan 2024 19:04:58 -0800:
> > >
> > > > Allow settings for on-die ecc such that if on-die ECC is selected
> > > > don't error out but require ECC strap setting of zero
> > > >
> > > > Signed-off-by: David Regan <dregan@xxxxxxxxxxxx>
> > > > Reviewed-by: William Zhang <william.zhang@xxxxxxxxxxxx>
> > > > ---
> > > > Changes in v3: None
> > > > ---
> > > > Changes in v2:
> > > > - Added to patch series
> > > > ---
> > > > drivers/mtd/nand/raw/brcmnand/brcmnand.c | 14 ++++++++++----
> > > > 1 file changed, 10 insertions(+), 4 deletions(-)
> > > >
> > > > diff --git a/drivers/mtd/nand/raw/brcmnand/brcmnand.c b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
> > > > index a4e311b6798c..42526f3250c9 100644
> > > > --- a/drivers/mtd/nand/raw/brcmnand/brcmnand.c
> > > > +++ b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
> > > > @@ -2727,9 +2727,11 @@ static int brcmnand_setup_dev(struct brcmnand_host *host)
> > > > cfg->blk_adr_bytes = get_blk_adr_bytes(mtd->size, mtd->writesize);
> > > >
> > > > if (chip->ecc.engine_type != NAND_ECC_ENGINE_TYPE_ON_HOST) {
> > > > - dev_err(ctrl->dev, "only HW ECC supported; selected: %d\n",
> > > > - chip->ecc.engine_type);
> > > > - return -EINVAL;
> > > > + if (chip->ecc.strength) {
> > > > + dev_err(ctrl->dev, "ERROR!!! HW ECC must be set to zero for non-hardware ECC; selected: %d\n",
> > > > + chip->ecc.strength);
> > >
> > > Can you use a more formal string? Also clarify it because I don't
> > > really understand what it leads to.
> >
> > How about:
> >
> > dev_err(ctrl->dev, "HW ECC set to %d, must be zero for on-die ECC\n",
>
> Actually I am wondering how legitimate this is. Just don't enable the
> on host ECC engine if it's not in use. No need to check the core's
> choice.
Our chip ECC engine will either be on if it's needed or off if it's not.
Either I can do that in one place or put checks in before each
read/write to turn on/off the ECC engine, which seems a lot more
work and changes and possible issues/problems.
Turning it on/off as needed has not been explicitly tested and
could cause unforeseen consequences. This
is a minimal change which should have minimal impact.
>
> >
> > >
> > > > + return -EINVAL;
> > > > + }
> > > > }
> > > >
> > > > if (chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN) {
> > > > @@ -2797,7 +2799,11 @@ static int brcmnand_setup_dev(struct brcmnand_host *host)
> > > > if (ret)
> > > > return ret;
> > > >
> > > > - brcmnand_set_ecc_enabled(host, 1);
> > > > + if (chip->ecc.engine_type == NAND_ECC_ENGINE_TYPE_ON_DIE) {
> > > > + dev_dbg(ctrl->dev, "Disable HW ECC for on-die ECC\n");
> > >
> > > Not needed.
> >
> > Will remove.
> >
> > >
> > > > + brcmnand_set_ecc_enabled(host, 0);
> > > > + } else
> > > > + brcmnand_set_ecc_enabled(host, 1);
> > >
> > > Style is wrong, but otherwise I think ECC should be kept disabled while
> > > not in active use, so I am a bit surprised by this line.
> >
> > This is a double check to turn on/off our hardware ECC.
>
> I expect the engine to be always disabled. Enable it only when you
> need (may require an additional patch before this one).
We are already turning on the ECC enable at this point,
this is just adding the option to turn it off if the NAND chip
itself will be doing the ECC instead of our controller.
>
> Thanks,
> Miquèl
Thanks!
-Dave
