Hi David,
dregan@xxxxxxxxxxxx wrote on Thu, 25 Jan 2024 11:47:46 -0800:
> Hi Miquèl,
>
> On Wed, Jan 24, 2024 at 9:40 AM Miquel Raynal <miquel.raynal@xxxxxxxxxxx> wrote:
> >
> > Hi David,
> >
> > dregan@xxxxxxxxxxxx wrote on Tue, 23 Jan 2024 19:04:58 -0800:
> >
> > > Allow settings for on-die ecc such that if on-die ECC is selected
> > > don't error out but require ECC strap setting of zero
> > >
> > > Signed-off-by: David Regan <dregan@xxxxxxxxxxxx>
> > > Reviewed-by: William Zhang <william.zhang@xxxxxxxxxxxx>
> > > ---
> > > Changes in v3: None
> > > ---
> > > Changes in v2:
> > > - Added to patch series
> > > ---
> > > drivers/mtd/nand/raw/brcmnand/brcmnand.c | 14 ++++++++++----
> > > 1 file changed, 10 insertions(+), 4 deletions(-)
> > >
> > > diff --git a/drivers/mtd/nand/raw/brcmnand/brcmnand.c b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
> > > index a4e311b6798c..42526f3250c9 100644
> > > --- a/drivers/mtd/nand/raw/brcmnand/brcmnand.c
> > > +++ b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
> > > @@ -2727,9 +2727,11 @@ static int brcmnand_setup_dev(struct brcmnand_host *host)
> > > cfg->blk_adr_bytes = get_blk_adr_bytes(mtd->size, mtd->writesize);
> > >
> > > if (chip->ecc.engine_type != NAND_ECC_ENGINE_TYPE_ON_HOST) {
> > > - dev_err(ctrl->dev, "only HW ECC supported; selected: %d\n",
> > > - chip->ecc.engine_type);
> > > - return -EINVAL;
> > > + if (chip->ecc.strength) {
> > > + dev_err(ctrl->dev, "ERROR!!! HW ECC must be set to zero for non-hardware ECC; selected: %d\n",
> > > + chip->ecc.strength);
> >
> > Can you use a more formal string? Also clarify it because I don't
> > really understand what it leads to.
>
> How about:
>
> dev_err(ctrl->dev, "HW ECC set to %d, must be zero for on-die ECC\n",
Actually I am wondering how legitimate this is. Just don't enable the
on host ECC engine if it's not in use. No need to check the core's
choice.
>
> >
> > > + return -EINVAL;
> > > + }
> > > }
> > >
> > > if (chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN) {
> > > @@ -2797,7 +2799,11 @@ static int brcmnand_setup_dev(struct brcmnand_host *host)
> > > if (ret)
> > > return ret;
> > >
> > > - brcmnand_set_ecc_enabled(host, 1);
> > > + if (chip->ecc.engine_type == NAND_ECC_ENGINE_TYPE_ON_DIE) {
> > > + dev_dbg(ctrl->dev, "Disable HW ECC for on-die ECC\n");
> >
> > Not needed.
>
> Will remove.
>
> >
> > > + brcmnand_set_ecc_enabled(host, 0);
> > > + } else
> > > + brcmnand_set_ecc_enabled(host, 1);
> >
> > Style is wrong, but otherwise I think ECC should be kept disabled while
> > not in active use, so I am a bit surprised by this line.
>
> This is a double check to turn on/off our hardware ECC.
I expect the engine to be always disabled. Enable it only when you
need (may require an additional patch before this one).
Thanks,
Miquèl
