On Fri, Jan 19, 2024 at 9:19 PM AngeloGioacchino Del Regno
<angelogioacchino.delregno@xxxxxxxxxxxxx> wrote:
>
> Il 14/12/23 15:37, Chen-Yu Tsai ha scritto:
> > On Thu, Dec 14, 2023 at 7:31 PM AngeloGioacchino Del Regno
> > <angelogioacchino.delregno@xxxxxxxxxxxxx> wrote:
> >>
> >> Il 13/12/23 16:04, Chen-Yu Tsai ha scritto:
> >>> Tentacruel and Tentacool are MT8186 based Chromebooks based on the
> >>> Krabby design.
> >>>
> >>> Tentacruel, also known as the ASUS Chromebook CM14 Flip CM1402F, is a
> >>> convertible device with touchscreen and stylus.
> >>>
> >>> Tentacool, also known as the ASUS Chromebook CM14 CM1402C, is a laptop
> >>> device. It does not have a touchscreen or stylus.
> >>>
> >>> The two devices both have two variants. The difference is a second
> >>> source touchpad controller that shares the same address as the original,
> >>> but is incompatible.
> >>>
> >>> The extra SKU IDs for the Tentacruel devices map to different sensor
> >>> components attached to the Embedded Controller. These are not visible
> >>> to the main processor.
> >>>
> >>> Signed-off-by: Chen-Yu Tsai <wenst@xxxxxxxxxxxx>
> >>> Acked-by: Conor Dooley <conor.dooley@xxxxxxxxxxxxx>
> >>> ---
> >>> Changes since v3:
> >>> - Reorder some properties to conform better to the newly proposed DT
> >>> style guidelines
> >>> - Drop unused labels
> >>> - Rename bt-sco node name to bt-sco-codec
> >>> - Drop i2s*-share properties from afe node
> >>> - Drop aud_gpio_tdm_{on,off} pinctrl nodes
> >>> - Replace interrupts with interrupts-extended in tpm node
> >>> - Enable adsp device
> >>>
> >>> Changes since v2:
> >>> - Picked up Conor's ack
> >>> - Rename touchpad to trackpad
> >>> - Drop pinctrl properties from trackpad in tentacruel/tentacool second
> >>> source trackpad
> >>>
> >>> Changes since v1:
> >>> - Reorder SKU numbers in descending order.
> >>> - Fixed pinconfig node names
> >>> - Moved pinctrl-* properties after interrupts-*
> >>> - Switched to interrupts-extended for external components
> >>> - Marked ADSP as explicitly disabled, with a comment explaining that it
> >>> stalls the system
> >>> - Renamed "touchpad" to "trackpad"
> >>> - Dropped bogus "no-laneswap" property from it6505 node
> >>> - Moved "realtek,jd-src" property to after all the regulator supplies
> >>> - Switched to macros for MT6366 regulator "regulator-allowed-modes"
> >>> - Renamed "vgpu" regulator name to allow coupling, with a comment
> >>> containing the name used in the design
> >>> - Renamed "cr50" node name to "tpm"
> >>> - Moved trackpad_pins reference up to i2c2; workaround for second source
> >>> component resource sharing.
> >>> - Fix copyright year
> >>> - Fixed touchscreen supply name
> >>> ---
> >>> arch/arm64/boot/dts/mediatek/Makefile | 4 +
> >>> .../dts/mediatek/mt8186-corsola-krabby.dtsi | 129 ++
> >>> .../mt8186-corsola-tentacool-sku327681.dts | 57 +
> >>> .../mt8186-corsola-tentacool-sku327683.dts | 24 +
> >>> .../mt8186-corsola-tentacruel-sku262144.dts | 44 +
> >>> .../mt8186-corsola-tentacruel-sku262148.dts | 26 +
> >>> .../boot/dts/mediatek/mt8186-corsola.dtsi | 1707 +++++++++++++++++
> >>> 7 files changed, 1991 insertions(+)
> >>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
> >>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
> >>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
> >>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
> >>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> >>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> >>>
> >>> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> >>> index e6e7592a3645..442af61b1305 100644
> >>> --- a/arch/arm64/boot/dts/mediatek/Makefile
> >>> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> >>> @@ -43,6 +43,10 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku32.dtb
> >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb
> >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
> >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb
> >>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacool-sku327681.dtb
> >>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacool-sku327683.dtb
> >>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacruel-sku262144.dtb
> >>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacruel-sku262148.dtb
> >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-evb.dtb
> >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-asurada-hayato-r1.dtb
> >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-asurada-hayato-r5-sku2.dtb
> >>
> >> ..snip..
> >>
> >>> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> >>> new file mode 100644
> >>> index 000000000000..447b57b12b41
> >>> --- /dev/null
> >>> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> >>> @@ -0,0 +1,26 @@
> >>> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> >>> +/*
> >>> + * Copyright 2023 Google LLC
> >>> + */
> >>> +
> >>> +#include "mt8186-corsola-tentacruel-sku262144.dts"
> >>> +
> >>> +/ {
> >>> + compatible = "google,tentacruel-sku262151", "google,tentacruel-sku262150",
> >>> + "google,tentacruel-sku262149", "google,tentacruel-sku262148",
> >>> + "google,tentacruel", "mediatek,mt8186";
> >>> +};
> >>> +
> >>> +/* This variant replaces only the trackpad controller. */
> >>> +&i2c2 {
> >>> + /delete-node/ trackpad@15;
> >>> +
> >>> + trackpad@15 {
> >>> + compatible = "hid-over-i2c";
> >>> + reg = <0x15>;
> >>> + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> >>> + hid-descr-addr = <0x0001>;
> >>> + vdd-supply = <&pp3300_s3>;
> >>> + wakeup-source;
> >>> + };
> >>> +};
> >>> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi b/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> >>> new file mode 100644
> >>> index 000000000000..adbeb0c765d3
> >>> --- /dev/null
> >>> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> >>> @@ -0,0 +1,1707 @@
> >>> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> >>> +/*
> >>> + * Copyright (C) 2022 MediaTek Inc.
> >>> + */
> >>> +/dts-v1/;
> >>> +#include "mt8186.dtsi"
> >>> +#include <dt-bindings/pinctrl/mt8186-pinfunc.h>
> >>> +#include <dt-bindings/gpio/gpio.h>
> >>> +#include <dt-bindings/input/input.h>
> >>> +#include <dt-bindings/input/gpio-keys.h>
> >>> +#include <dt-bindings/regulator/mediatek,mt6397-regulator.h>
> >>> +
> >>
> >> ..snip..
> >>
> >>> +
> >>> +&i2c2 {
> >>> + pinctrl-names = "default";
> >>> + /*
> >>> + * Trackpad pin put here to work around second source components
> >>> + * sharing the pinmux in steelix designs.
> >>> + */
> >>> + pinctrl-0 = <&i2c2_pins>, <&trackpad_pin>;
> >>> + clock-frequency = <400000>;
> >>> + i2c-scl-internal-delay-ns = <10000>;
> >>> + status = "okay";
> >>> +
> >>> + trackpad@15 {
> >>> + compatible = "elan,ekth3000";
> >>
> >> You forgot to change this one.
> >>
> >> Remove compatible from this node and stop using /delete-node/ in device specific
> >> devicetrees.
> >
> > I believe I already replied to the previous version why we can't and shouldn't
> > do that.
> >
> > "elan,ekth3000" and "hid-over-i2c" have incompatible bindings, specifically
> > the former uses "vcc-supply" while the latter uses "vdd-supply".
> >
> > One has to track down if a property is a "sharable" property or not,
> > then put it in the correct place, otherwise getting DT binding validation
> > errors.
> >
> > To me it seems cleaner to just delete the node wholesale to not have any
> > remnants of the original node, i.e. start from a clean slate. Trying to
> > "share" common properties is asking for a headache.
> >
> > This feels more like a preference thing. I also asked if deleting the node
> > through the label would be cleaner, but you didn't reply.
> >
>
> I am truly sorry for not replying to that - and for replying to this one very late.
>
> Ok, in that case, I still don't really like seeing /delete-node/ statements... and
> unless there is a truly valid reason to have those, can we please just get each
> node to each *.dts?
>
> Just to clarify, a valid scenario to have a /delete-node/ statement there would be
> the following:
> - Same platform, like Corsola in this case
> - Four devices
> - Three have one trackpad (better if expected more with the same TP)
> - One has the other trackpad
>
> Even though I am flexible with that, I just don't see the value in deleting the
> trackpad because we've got a 50-50 situation here!
>
> At this point IMO it's worth defining the trackpad twice + twice instead... but
> if you expect to have more devices, conforming to the valid scenario that I have
> described above, then okay - keep going with /delete-node/.
It's not 50-50, because all the other MT8186 devices inherit the original
trackpad in mt8186-corsola.dtsi. So for those devices it either means
pushing it down to the next level in mt8186-corsola-steelix.dtsi, or
down to the individual .dts files, of which we already have six within
this series, and another two for the Voltorb devices. So that's 10 vs 2.
I think that makes a very valid case for using /delete-node/ and not
duplicating the device node everywhere?
Maybe we'll be able to clean this mess up a bit with overlays and FIT
images, but the FIT image stuff is still under discussion.
ChenYu
> > Also, "elan,ekth3000" is the one that was designed and tested on the Corsola
> > reference design, so I think it rightfully belongs there. The Tentacruel
> > SKU replaced it with another part, so the original part should be disabled,
> > or in this case, deleted, because otherwise there would be a conflict.
>
> If you really want to document the fact that the Corsola Reference Design
> suggests to use a Elan eKTH3000 part, you can always leave a comment in the
> dtsi, though, that's interesting mostly only to OEMs... but anyway I'm not
> against having a comment, at all.
>
> Cheers,
> Angelo
>
> >
> >
> > Regards
> > ChenYu
> >
> >
> >
> >>> + reg = <0x15>;
> >>> + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> >>> + vcc-supply = <&pp3300_s3>;
> >>> + wakeup-source;
> >>> + };
> >>> +};
> >>
> >>
> >> corsola.dtsi (here):
> >>
> >> &i2c2 {
> >> pinctrl-names = "default";
> >> /*
> >> * Trackpad pin put here to work around second source components
> >> * sharing the pinmux in steelix designs.
> >> */
> >> pinctrl-0 = <&i2c2_pins>, <&trackpad_pin>;
> >> clock-frequency = <400000>;
> >> i2c-scl-internal-delay-ns = <10000>;
> >> status = "okay";
> >>
> >> trackpad_i2c2_15: trackpad@15 {
> >> /*
> >> * Those are common properties for i2c2 trackpad on Corsola boards.
> >> * The compatible string is declared in device specific devicetrees
> >> */
> >> reg = <0x15>;
> >> interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> >> vcc-supply = <&pp3300_s3>;
> >> wakeup-source;
> >> status = "disabled";
> >> };
> >> };
> >>
> >> corsola-some-device.dts:
> >>
> >> &trackpad_i2c2_15 {
> >> compatible = "hid-over-i2c";
> >> hid-descr-addr = <0x0001>;
> >> status = "okay";
> >> };
> >>
> >> corsola-some-other-device.dts:
> >>
> >> &trackpad_i2c2_15 {
> >> compatible = "elan,ekth3000";
> >> status = "okay";
> >> };
> >>
> >> ....everything else looks good.
> >>
> >> Cheers,
> >> Angelo
>
>
>
