The Sipeed Longan SoM 3H is a system on module based on the Allwinner
H618 SoC. The SoM features:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 2/4 GiB LPDDR4 DRAM SoMs
- AXP313a PMIC
- eMMC
The Sipeed Longan PI 3H is a development board based on the above SoM.
The board features:
- Longan SoM 3H
- Raspberry-Pi-1 compatible GPIO header
- 2 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- 1Gbps Ethernet port (via RTL8211 PHY)
- HDMI port
- WiFi/BT chip
Add the devicetree file describing the currently supported features,
namely PMIC, LEDs, UART, SD card, eMMC, USB and Ethernet.
Signed-off-by: Jisheng Zhang <jszhang@xxxxxxxxxx>
---
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../sun50i-h618-longan-module-3h.dtsi | 82 +++++++++++
.../dts/allwinner/sun50i-h618-longanpi-3h.dts | 133 ++++++++++++++++++
3 files changed, 216 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h618-longan-module-3h.dtsi
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h618-longanpi-3h.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 3aca6787a167..00db504a9b8c 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -42,4 +42,5 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-bigtreetech-cb1-manta.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-bigtreetech-pi.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-longanpi-3h.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h618-longan-module-3h.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h618-longan-module-3h.dtsi
new file mode 100644
index 000000000000..88a7d287b73c
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h618-longan-module-3h.dtsi
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) Jisheng Zhang <jszhang@xxxxxxxxxx>
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+/ {
+ model = "Sipeed Longan Module 3H";
+ compatible = "sipeed,longan-module-3h", "allwinner,sun50i-h618";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+ vmmc-supply = <®_dldo1>;
+ vqmmc-supply = <®_aldo1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ status = "okay";
+};
+
+&r_i2c {
+ status = "okay";
+
+ axp313: pmic@36 {
+ compatible = "x-powers,axp313a";
+ reg = <0x36>;
+
+ regulators {
+ /* Supplies VCC-PLL, so needs to be always on. */
+ reg_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8";
+ };
+
+ /* Supplies VCC-IO, so needs to be always on. */
+ reg_dldo1: dldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3";
+ };
+
+ reg_dcdc1: dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <990000>;
+ regulator-name = "vdd-gpu-sys";
+ };
+
+ reg_dcdc2: dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpu";
+ };
+
+ reg_dcdc3: dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-dram";
+ };
+ };
+ };
+};
+
+&pio {
+ vcc-pc-supply = <®_dldo1>;
+ vcc-pf-supply = <®_dldo1>;
+ vcc-pg-supply = <®_aldo1>;
+ vcc-ph-supply = <®_dldo1>;
+ vcc-pi-supply = <®_dldo1>;
+};
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h618-longanpi-3h.dts b/arch/arm64/boot/dts/allwinner/sun50i-h618-longanpi-3h.dts
new file mode 100644
index 000000000000..245583881549
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h618-longanpi-3h.dts
@@ -0,0 +1,133 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) Jisheng Zhang <jszhang@xxxxxxxxxx>
+ */
+
+/dts-v1/;
+
+#include "sun50i-h618-longan-module-3h.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Sipeed Longan Pi 3H";
+ compatible = "sipeed,longan-pi-3h", "sipeed,longan-module-3h", "allwinner,sun50i-h618";
+
+ aliases {
+ ethernet0 = &emac0;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ color = <LED_COLOR_ID_ORANGE>;
+ function = LED_FUNCTION_INDICATOR;
+ function-enumerator = <0>;
+ gpios = <&pio 6 2 GPIO_ACTIVE_LOW>; /* PG2 */
+ };
+
+ led-1 {
+ color = <LED_COLOR_ID_ORANGE>;
+ function = LED_FUNCTION_INDICATOR;
+ function-enumerator = <1>;
+ gpios = <&pio 6 4 GPIO_ACTIVE_LOW>; /* PG4 */
+ };
+ };
+
+ reg_vcc5v: vcc5v {
+ /* board wide 5V supply directly from the USB-C socket */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+};
+
+&axp313 {
+ vin1-supply = <®_vcc5v>;
+ vin2-supply = <®_vcc5v>;
+ vin3-supply = <®_vcc5v>;
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&emac0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ext_rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ allwinner,rx-delay-ps = <3100>;
+ allwinner,tx-delay-ps = <700>;
+ phy-supply = <®_dldo1>;
+ status = "okay";
+};
+
+&mdio0 {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ vmmc-supply = <®_dldo1>;
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&usbotg {
+ /*
+ * PHY0 pins are connected to a USB-C socket, but a role switch
+ * is not implemented: both CC pins are pulled to GND.
+ * The VBUS pins power the device, so a fixed peripheral mode
+ * is the best choice.
+ * The board can be powered via GPIOs, in this case port0 *can*
+ * act as a host (with a cable/adapter ignoring CC), as VBUS is
+ * then provided by the GPIOs. Any user of this setup would
+ * need to adjust the DT accordingly: dr_mode set to "host",
+ * enabling OHCI0 and EHCI0.
+ */
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_vcc5v>;
+ status = "okay";
+};
--
2.40.0
