On 01/20/2015 12:21 PM, Lee Jones wrote:
On Fri, 09 Jan 2015, Jacek Anaszewski wrote:
This patch adds device tree binding documentation for
the flash cell of the Maxim max77693 multifunctional device.
Signed-off-by: Jacek Anaszewski <j.anaszewski@xxxxxxxxxxx>
Signed-off-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx>
Acked-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
Cc: Lee Jones <lee.jones@xxxxxxxxxx>
Cc: Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
Cc: Bryan Wu <cooloney@xxxxxxxxx>
Cc: Richard Purdie <rpurdie@xxxxxxxxx>
Cc: Rob Herring <robh+dt@xxxxxxxxxx>
Cc: Pawel Moll <pawel.moll@xxxxxxx>
Cc: Mark Rutland <mark.rutland@xxxxxxx>
Cc: Ian Campbell <ijc+devicetree@xxxxxxxxxxxxxx>
Cc: Kumar Gala <galak@xxxxxxxxxxxxxx>
---
Documentation/devicetree/bindings/mfd/max77693.txt | 69 ++++++++++++++++++++
1 file changed, 69 insertions(+)
diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt
index 01e9f30..ef184f0 100644
--- a/Documentation/devicetree/bindings/mfd/max77693.txt
+++ b/Documentation/devicetree/bindings/mfd/max77693.txt
@@ -41,7 +41,52 @@ Optional properties:
To get more informations, please refer to documentaion.
[*] refer Documentation/devicetree/bindings/pwm/pwm.txt
+- led : the LED submodule device node
+
+There are two led outputs available - fled1 and fled2. Each of them can
+control a separate led or they can be connected together to double
+the maximum current for a single connected led. One led is represented
+by one child node.
+
+Required properties:
+- compatible : Must be "maxim,max77693-led".
+
+Optional properties:
+- maxim,trigger-type : Flash trigger type.
+ Possible trigger types:
+ MAX77693_LED_TRIG_TYPE_EDGE - Rising edge of the signal triggers
+ the flash,
+ MAX77693_LED_TRIG_TYPE_LEVEL - Strobe pulse length controls
+ duration of the flash.
I think you should represent the proper values here instead of the
defines.
I see both versions in the existing bindings and also a combination of
them, e.g.: MAX77693_LED_TRIG_TYPE_EDGE (0). I think that it is
reasonable to mention the macros, especially if they are to appear
in the DT binding example at the end of the documentation file.
+- maxim,boost-mode :
+ In boost mode the device can produce up to 1.2A of total current
+ on both outputs. The maximum current on each output is reduced
+ to 625mA then. If not enabled explicitly, boost setting defaults to
+ MAX77693_LED_BOOST_FIXED in case both current sources are used.
+ Possible values:
+ MAX77693_LED_BOOST_OFF - no boost,
+ MAX77693_LED_BOOST_ADAPTIVE - adaptive mode,
+ MAX77693_LED_BOOST_FIXED - fixed mode.
Same here.
MAX77693_LED_BOOST_OFF (0) - no boost,
MAX77693_LED_BOOST_ADAPTIVE (1) - adaptive mode,
MAX77693_LED_BOOST_FIXED (2) - fixed mode.
?
+- maxim,boost-vout : Output voltage of the boost module in millivolts.
-mvout?
-microvout?
maxim,boost-mvout ?
+- maxim,vsys-min : Low input voltage level in millivolts. Flash is not fired
+ if chip estimates that system voltage could drop below this level due
+ to flash power consumption.
mvsys?
microvsys?
maxim,mvsys-min ?
--
Best Regards,
Jacek Anaszewski
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
