Hi Alexander, > > Hi, > > thanks for the patch. > > Am Donnerstag, 14. Dezember 2023, 12:24:42 CET schrieb Xu Yang: > > There are 2 Type-C ports and 2 USB controllers on i.MX93. Enable them. > > > > Signed-off-by: Xu Yang <xu.yang_2@xxxxxxx> > > --- > > .../boot/dts/freescale/imx93-11x11-evk.dts | 108 ++++++++++++++++++ > > 1 file changed, 108 insertions(+) > > > > diff --git a/arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts > > b/arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts index > > 2b9d47716f75..42b1ea7d5220 100644 > > --- a/arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts > > +++ b/arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts > > @@ -5,6 +5,7 @@ > > > > /dts-v1/; > > > > +#include <dt-bindings/usb/pd.h> > > #include "imx93.dtsi" > > > > / { > > @@ -103,6 +104,70 @@ &mu2 { > > status = "okay"; > > }; > > > > +&lpi2c3 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + clock-frequency = <400000>; > > + pinctrl-names = "default", "sleep"; > > + pinctrl-0 = <&pinctrl_lpi2c3>; > > + pinctrl-1 = <&pinctrl_lpi2c3>; > > + status = "okay"; > > + > > + ptn5110: tcpc@50 { > > I do not know if there is already some consent, but personally I do not like > tcpc for the node name. Maybe change that to usb-typec@50. It really doesn't matter. The connector node will clear say it's a typec port. > > > + compatible = "nxp,ptn5110"; > > + reg = <0x50>; > > + interrupt-parent = <&gpio3>; > > + interrupts = <27 IRQ_TYPE_LEVEL_LOW>; > > + status = "okay"; > > status not needed here, "okay" is default and node is added here. Yeah. > > > + > > + port { > > + typec1_dr_sw: endpoint { > > + remote-endpoint = <&usb1_drd_sw>; > > + }; > > + }; > > + > > + typec1_con: connector { > > + compatible = "usb-c-connector"; > > + label = "USB-C"; > > + power-role = "dual"; > > + data-role = "dual"; > > + try-power-role = "sink"; > > + source-pdos = <PDO_FIXED(5000, 3000, > PDO_FIXED_USB_COMM)>; > > + sink-pdos = <PDO_FIXED(5000, 3000, > PDO_FIXED_USB_COMM) > > + PDO_VAR(5000, 20000, 3000)>; > > + op-sink-microwatt = <15000000>; > > + self-powered; > > + }; > > + }; > > + > > + ptn5110_2: tcpc@51 { > > See above. > > > + compatible = "nxp,ptn5110"; > > + reg = <0x51>; > > + interrupt-parent = <&gpio3>; > > + interrupts = <27 IRQ_TYPE_LEVEL_LOW>; > > + status = "okay"; > > See above. Okay. Thanks, Xu Yang > > Best regards, > Alexander > > > + > > + port { > > + typec2_dr_sw: endpoint { > > + remote-endpoint = <&usb2_drd_sw>; > > + }; > > + }; > > + > > + typec2_con: connector { > > + compatible = "usb-c-connector"; > > + label = "USB-C"; > > + power-role = "dual"; > > + data-role = "dual"; > > + try-power-role = "sink"; > > + source-pdos = <PDO_FIXED(5000, 3000, > PDO_FIXED_USB_COMM)>; > > + sink-pdos = <PDO_FIXED(5000, 3000, > PDO_FIXED_USB_COMM) > > + PDO_VAR(5000, 20000, 3000)>; > > + op-sink-microwatt = <15000000>; > > + self-powered; > > + }; > > + }; > > +}; > > + > > &eqos { > > pinctrl-names = "default"; > > pinctrl-0 = <&pinctrl_eqos>; > > @@ -155,6 +220,42 @@ &lpuart5 { > > status = "okay"; > > }; > > > > +&usbotg1 { > > + dr_mode = "otg"; > > + hnp-disable; > > + srp-disable; > > + adp-disable; > > + usb-role-switch; > > + disable-over-current; > > + samsung,picophy-pre-emp-curr-control = <3>; > > + samsung,picophy-dc-vol-level-adjust = <7>; > > + status = "okay"; > > + > > + port { > > + usb1_drd_sw: endpoint { > > + remote-endpoint = <&typec1_dr_sw>; > > + }; > > + }; > > +}; > > + > > +&usbotg2 { > > + dr_mode = "otg"; > > + hnp-disable; > > + srp-disable; > > + adp-disable; > > + usb-role-switch; > > + disable-over-current; > > + samsung,picophy-pre-emp-curr-control = <3>; > > + samsung,picophy-dc-vol-level-adjust = <7>; > > + status = "okay"; > > + > > + port { > > + usb2_drd_sw: endpoint { > > + remote-endpoint = <&typec2_dr_sw>; > > + }; > > + }; > > +}; > > + > > &usdhc1 { > > pinctrl-names = "default", "state_100mhz", "state_200mhz"; > > pinctrl-0 = <&pinctrl_usdhc1>; > > @@ -221,6 +322,13 @@ MX93_PAD_ENET2_TX_CTL__ENET1_RGMII_TX_CTL 0x57e > > > > >; > > > > }; > > > > + pinctrl_lpi2c3: lpi2c3grp { > > + fsl,pins = < > > + MX93_PAD_GPIO_IO28__LPI2C3_SDA > 0x40000b9e > > + MX93_PAD_GPIO_IO29__LPI2C3_SCL > 0x40000b9e > > + >; > > + }; > > + > > pinctrl_uart1: uart1grp { > > fsl,pins = < > > MX93_PAD_UART1_RXD__LPUART1_RX > 0x31e > >