Hi Paul!
Sorry for late reply.
On Wednesday, November 22, 2023 3:14:21 PM CET Paul Kocialkowski wrote:
> MIPI CSI-2 is supported on the V3s with an A31-based MIPI CSI-2 bridge
> controller. The controller uses a separate D-PHY, which is the same
> that is otherwise used for MIPI DSI, but used in Rx mode.
>
> On the V3s, the CSI0 controller is dedicated to MIPI CSI-2 as it does
> not have access to any parallel interface pins.
>
> Add all the necessary nodes (CSI0, MIPI CSI-2 bridge and D-PHY) to
> support the MIPI CSI-2 interface.
>
> Note that a fwnode graph link is created between CSI0 and MIPI CSI-2
> even when no sensor is connected. This will result in a probe failure
> for the controller as long as no sensor is connected but this is fine
> since no other interface is available.
>
> The interconnects property is used to inherit the proper DMA offset.
>
> Signed-off-by: Paul Kocialkowski <paul.kocialkowski@xxxxxxxxxxx>
> ---
> arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi | 71 ++++++++++++++++++++++
> 1 file changed, 71 insertions(+)
>
> diff --git a/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi b/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi
> index 506e98f4f69d..d57612023aa4 100644
> --- a/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi
> +++ b/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi
> @@ -621,6 +621,77 @@ gic: interrupt-controller@1c81000 {
> interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> };
>
> + csi0: camera@1cb0000 {
> + compatible = "allwinner,sun8i-v3s-csi";
> + reg = <0x01cb0000 0x1000>;
> + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_CSI>,
> + <&ccu CLK_CSI1_SCLK>,
> + <&ccu CLK_DRAM_CSI>;
> + clock-names = "bus", "mod", "ram";
> + resets = <&ccu RST_BUS_CSI>;
> + interconnects = <&mbus 5>;
> + interconnect-names = "dma-mem";
As far as I can see, interconnects are not documented in
allwinner,sun6i-a31-csi.yaml. Please run make dtbs_check on this.
Best regards,
Jernej
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@1 {
> + reg = <1>;
> +
> + csi0_in_mipi_csi2: endpoint {
> + remote-endpoint = <&mipi_csi2_out_csi0>;
> + };
> + };
> + };
> + };
> +
> + mipi_csi2: csi@1cb1000 {
> + compatible = "allwinner,sun8i-v3s-mipi-csi2",
> + "allwinner,sun6i-a31-mipi-csi2";
> + reg = <0x01cb1000 0x1000>;
> + interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_CSI>,
> + <&ccu CLK_CSI1_SCLK>;
> + clock-names = "bus", "mod";
> + resets = <&ccu RST_BUS_CSI>;
> + status = "disabled";
> +
> + phys = <&dphy>;
> + phy-names = "dphy";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + mipi_csi2_in: port@0 {
> + reg = <0>;
> + };
> +
> + mipi_csi2_out: port@1 {
> + reg = <1>;
> +
> + mipi_csi2_out_csi0: endpoint {
> + remote-endpoint = <&csi0_in_mipi_csi2>;
> + };
> + };
> + };
> + };
> +
> + dphy: d-phy@1cb2000 {
> + compatible = "allwinner,sun6i-a31-mipi-dphy";
> + reg = <0x01cb2000 0x1000>;
> + clocks = <&ccu CLK_BUS_CSI>,
> + <&ccu CLK_MIPI_CSI>;
> + clock-names = "bus", "mod";
> + resets = <&ccu RST_BUS_CSI>;
> + allwinner,direction = "rx";
> + status = "disabled";
> + #phy-cells = <0>;
> + };
> +
> csi1: camera@1cb4000 {
> compatible = "allwinner,sun8i-v3s-csi";
> reg = <0x01cb4000 0x3000>;
>
