Re: [PATCH v2 1/1] arm64: dts: ti: k3-am62-wakeup: Configure ti-sysc for wkup_uart0

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Tony Lindgren <tony@xxxxxxxxxxx> writes:

> The devices in the wkup domain are capable of waking up the system from
> suspend. We can configure the wkup domain devices in a generic way using
> the ti-sysc interconnect target module driver like we have done with the
> earlier TI SoCs.
>
> As ti-sysc manages the SYSCONFIG related registers independent of the
> child hardware device, the wake-up configuration is also set even if
> wkup_uart0 is reserved by sysfw.
>
> The wkup_uart0 device has interconnect target module register mapping like
> dra7 wkup uart. There is a 1 MB interconnect target range with one uart IP
> block in the target module. The power domain and clock affects the whole
> interconnect target module.
>
> Note we change the functional clock name to follow the ti-sysc binding
> and use "fck" instead of "fclk".
>
> Tested-by: Dhruva Gole <d-gole@xxxxxx>
> Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx>
> ---
>
> Changes since v1:
>
> - Added Tested-by from Dhruva
>
> ---
>  arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi | 33 ++++++++++++++++++----
>  1 file changed, 27 insertions(+), 6 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi
> --- a/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi
> @@ -5,6 +5,8 @@
>   * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/
>   */
>  
> +#include <dt-bindings/bus/ti-sysc.h>
> +
>  &cbass_wakeup {
>  	wkup_conf: syscon@43000000 {
>  		bootph-all;
> @@ -21,14 +23,33 @@ chipid: chipid@14 {
>  		};
>  	};
>  
> -	wkup_uart0: serial@2b300000 {
> -		compatible = "ti,am64-uart", "ti,am654-uart";
> -		reg = <0x00 0x2b300000 0x00 0x100>;
> -		interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
> +	target-module@2b300000 {
> +		compatible = "ti,sysc-omap2", "ti,sysc";
> +		reg = <0 0x2b300050 0 0x4>,
> +		      <0 0x2b300054 0 0x4>,
> +		      <0 0x2b300058 0 0x4>;
> +		reg-names = "rev", "sysc", "syss";
> +		ti,sysc-mask = <(SYSC_OMAP2_ENAWAKEUP |
> +				 SYSC_OMAP2_SOFTRESET |
> +				 SYSC_OMAP2_AUTOIDLE)>;
> +		ti,sysc-sidle = <SYSC_IDLE_FORCE>,
> +				<SYSC_IDLE_NO>,
> +				<SYSC_IDLE_SMART>,
> +				<SYSC_IDLE_SMART_WKUP>;
> +		ti,syss-mask = <1>;
>  		power-domains = <&k3_pds 114 TI_SCI_PD_EXCLUSIVE>;
>  		clocks = <&k3_clks 114 0>;

I'm a little confused why these power-domain and clocks stay here and
are not moved under the wkup_uart0 node... 

> -		clock-names = "fclk";
> -		status = "disabled";
> +		clock-names = "fck";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges = <0 0 0x2b300000 0x100000>;
> +
> +		wkup_uart0: serial@2b300000 {
> +			compatible = "ti,am64-uart", "ti,am654-uart";
> +			reg = <0 0x100>;
> +			interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
> +			status = "disabled";

...here.

The SCI device ID 114 is specifically for wkup_uart0[1], so it seems to
me those should be in the wkup_uart0 node.

Kevin

[1] https://software-dl.ti.com/tisci/esd/latest/5_soc_doc/am62x/devices.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux