On 11/15/23 2:52 AM, Siddharth Vadapalli wrote:
Add overlay to enable the PCIE0 instance of PCIe on J721E-EVM in
Endpoint mode of operation.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@xxxxxx>
---
arch/arm64/boot/dts/ti/Makefile | 3 ++
.../boot/dts/ti/k3-j721e-evm-pcie0-ep.dtso | 53 +++++++++++++++++++
2 files changed, 56 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-evm-pcie0-ep.dtso
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 77a347f9f47d..5620db44d4dc 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -66,6 +66,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-j7200-evm.dtb
k3-j721e-evm-dtbs := k3-j721e-common-proc-board.dtb k3-j721e-evm-quad-port-eth-exp.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-j721e-beagleboneai64.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm.dtb
+k3-j721e-evm-pcie0-ep-dtbs := k3-j721e-evm.dtb k3-j721e-evm-pcie0-ep.dtbo
+dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm-pcie0-ep.dtb
Do you really need to produce this pre-combined DTB file? If you would rather
just the overlay produced which could be applied at load-time (I prefer this),
then you should do as Jai has done[0]. Add just the overlay, and test its
application using a dummy target.
Andrew
[0] https://www.spinics.net/lists/kernel/msg5015247.html
dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm-gesi-exp-board.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-j721e-sk.dtb
@@ -85,4 +87,5 @@ DTC_FLAGS_k3-am625-sk += -@
DTC_FLAGS_k3-am62-lp-sk += -@
DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
DTC_FLAGS_k3-j721e-common-proc-board += -@
+DTC_FLAGS_k3-j721e-evm += -@
DTC_FLAGS_k3-j721s2-common-proc-board += -@
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-evm-pcie0-ep.dtso b/arch/arm64/boot/dts/ti/k3-j721e-evm-pcie0-ep.dtso
new file mode 100644
index 000000000000..0c82a13b65a4
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j721e-evm-pcie0-ep.dtso
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: GPL-2.0
+/**
+ * DT Overlay for enabling PCIE0 instance in Endpoint Configuration with the
+ * J7 common processor board.
+ *
+ * J7 Common Processor Board Product Link: https://www.ti.com/tool/J721EXCPXEVM
+ *
+ * Copyright (C) 2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/soc/ti,sci_pm_domain.h>
+
+#include "k3-pinctrl.h"
+
+/*
+ * Since Root Complex and Endpoint modes are mutually exclusive
+ * disable Root Complex mode.
+ */
+&pcie0_rc {
+ status = "disabled";
+};
+
+&cbass_main {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&gic500>;
+
+ pcie0_ep: pcie-ep@2900000 {
+ compatible = "ti,j721e-pcie-ep";
+ reg = <0x00 0x02900000 0x00 0x1000>,
+ <0x00 0x02907000 0x00 0x400>,
+ <0x00 0x0d000000 0x00 0x00800000>,
+ <0x00 0x10000000 0x00 0x08000000>;
+ reg-names = "intd_cfg", "user_cfg", "reg", "mem";
+ interrupt-names = "link_state";
+ interrupts = <GIC_SPI 318 IRQ_TYPE_EDGE_RISING>;
+ ti,syscon-pcie-ctrl = <&scm_conf 0x4070>;
+ max-link-speed = <3>;
+ num-lanes = <1>;
+ power-domains = <&k3_pds 239 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 239 1>;
+ clock-names = "fck";
+ max-functions = /bits/ 8 <6>;
+ max-virtual-functions = /bits/ 8 <4 4 4 4 0 0>;
+ dma-coherent;
+ phys = <&serdes0_pcie_link>;
+ phy-names = "pcie-phy";
+ };
+};
