Il 30/11/23 07:15, Axe Yang ha scritto:
Previously, during the MSDC calibration process, a full clock cycle
actually not be covered, which in some cases didn't yield the best
results and could cause CRC errors. This problem is particularly
evident when MSDC is used as an SDIO host. In fact, MSDC support
tuning up to a maximum of 64 steps, but by default, the step number
is 32. By increase the tuning step, we are more likely to cover more
parts of a clock cycle, and get better calibration result.
To illustrate, when tuning 32 steps, if the obtained window has a hole
near the middle, like this: 0xffc07ff (hex), then the selected delay
will be the 6 (counting from right to left).
(32 <- 1)
1111 1111 1100 0000 0000 0111 11(1)1 1111
However, if we tune 64 steps, the window obtained may look like this:
0xfffffffffffc07ff. The final selected delay will be 44, which is
safer as it is further away from the hole:
(64 <- 1)
1111 ... (1)111 1111 1111 1111 1111 1100 0000 0000 0111 1111 1111
In this case, delay 6 selected through 32 steps tuning is obviously
not optimal, and this delay is closer to the hole, using it would
easily cause CRC problems.
You will need to configure property "mediatek,tuning-step" in MSDC
dts node to 64 to extend the steps.
Signed-off-by: Axe Yang <axe.yang@xxxxxxxxxxxx>
---
drivers/mmc/host/mtk-sd.c | 155 ++++++++++++++++++++++++++------------
1 file changed, 107 insertions(+), 48 deletions(-)
diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
index 97f7c3d4be6e..4cd306b3b295 100644
--- a/drivers/mmc/host/mtk-sd.c
+++ b/drivers/mmc/host/mtk-sd.c
@@ -252,12 +252,16 @@
#define MSDC_PAD_TUNE_DATWRDLY GENMASK(4, 0) /* RW */
#define MSDC_PAD_TUNE_DATRRDLY GENMASK(12, 8) /* RW */
+#define MSDC_PAD_TUNE_DATRRDLY2 GENMASK(12, 8) /* RW */
#define MSDC_PAD_TUNE_CMDRDLY GENMASK(20, 16) /* RW */
+#define MSDC_PAD_TUNE_CMDRDLY2 GENMASK(20, 16) /* RW */
#define MSDC_PAD_TUNE_CMDRRDLY GENMASK(26, 22) /* RW */
#define MSDC_PAD_TUNE_CLKTDLY GENMASK(31, 27) /* RW */
#define MSDC_PAD_TUNE_RXDLYSEL BIT(15) /* RW */
#define MSDC_PAD_TUNE_RD_SEL BIT(13) /* RW */
#define MSDC_PAD_TUNE_CMD_SEL BIT(21) /* RW */
+#define MSDC_PAD_TUNE_RD2_SEL BIT(13) /* RW */
+#define MSDC_PAD_TUNE_CMD2_SEL BIT(21) /* RW */
#define PAD_DS_TUNE_DLY_SEL BIT(0) /* RW */
#define PAD_DS_TUNE_DLY1 GENMASK(6, 2) /* RW */
@@ -325,7 +329,8 @@
#define DEFAULT_DEBOUNCE (8) /* 8 cycles CD debounce */
-#define PAD_DELAY_MAX 32 /* PAD delay cells */
+#define PAD_DELAY_HALF 32 /* PAD delay cells */
+#define PAD_DELAY_FULL 64
/*--------------------------------------------------------------------------*/
/* Descriptor Structure */
/*--------------------------------------------------------------------------*/
@@ -461,6 +466,7 @@ struct msdc_host {
u32 hs400_ds_dly3;
u32 hs200_cmd_int_delay; /* cmd internal delay for HS200/SDR104 */
u32 hs400_cmd_int_delay; /* cmd internal delay for HS400 */
+ u32 tuning_step;
bool hs400_cmd_resp_sel_rising;
/* cmd response sample selection for HS400 */
bool hs400_mode; /* current eMMC will run at hs400 mode */
@@ -1615,7 +1621,7 @@ static irqreturn_t msdc_cmdq_irq(struct msdc_host *host, u32 intsts)
}
if (cmd_err || dat_err) {
- dev_err(host->dev, "cmd_err = %d, dat_err =%d, intsts = 0x%x",
+ dev_err(host->dev, "cmd_err = %d, dat_err = %d, intsts = 0x%x",
cmd_err, dat_err, intsts);
}
@@ -1780,10 +1786,20 @@ static void msdc_init_hw(struct msdc_host *host)
DATA_K_VALUE_SEL);
sdr_set_bits(host->top_base + EMMC_TOP_CMD,
PAD_CMD_RD_RXDLY_SEL);
+ if (host->tuning_step > PAD_DELAY_HALF) {
+ sdr_set_bits(host->top_base + EMMC_TOP_CONTROL,
+ PAD_DAT_RD_RXDLY2_SEL);
+ sdr_set_bits(host->top_base + EMMC_TOP_CMD,
+ PAD_CMD_RD_RXDLY2_SEL);
+ }
} else {
sdr_set_bits(host->base + tune_reg,
MSDC_PAD_TUNE_RD_SEL |
MSDC_PAD_TUNE_CMD_SEL);
+ if (host->tuning_step > PAD_DELAY_HALF)
+ sdr_set_bits(host->base + tune_reg + 4,
`tune_reg + 4` is a different register, please define it.
Also, I can't find this in MT8192, MT8195 - as those bits seem to be undefined,
so, which SoCs are actually compatible with this change?
+ MSDC_PAD_TUNE_RD2_SEL |
+ MSDC_PAD_TUNE_CMD2_SEL);
}
} else {
/* choose clock tune */
@@ -1925,24 +1941,24 @@ static void msdc_ops_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
msdc_set_mclk(host, ios->timing, ios->clock);
}
-static u32 test_delay_bit(u32 delay, u32 bit)
+static u64 test_delay_bit(u64 delay, u32 bit)
{
- bit %= PAD_DELAY_MAX;
- return delay & BIT(bit);
+ bit %= PAD_DELAY_FULL;
+ return delay & BIT_ULL(bit);
}
-static int get_delay_len(u32 delay, u32 start_bit)
+static int get_delay_len(u64 delay, u32 start_bit)
{
int i;
- for (i = 0; i < (PAD_DELAY_MAX - start_bit); i++) {
+ for (i = 0; i < (PAD_DELAY_FULL - start_bit); i++) {
if (test_delay_bit(delay, start_bit + i) == 0)
return i;
}
- return PAD_DELAY_MAX - start_bit;
+ return PAD_DELAY_FULL - start_bit;
}
-static struct msdc_delay_phase get_best_delay(struct msdc_host *host, u32 delay)
+static struct msdc_delay_phase get_best_delay(struct msdc_host *host, u64 delay)
{
int start = 0, len = 0;
int start_final = 0, len_final = 0;
@@ -1950,28 +1966,28 @@ static struct msdc_delay_phase get_best_delay(struct msdc_host *host, u32 delay)
struct msdc_delay_phase delay_phase = { 0, };
if (delay == 0) {
- dev_err(host->dev, "phase error: [map:%x]\n", delay);
+ dev_err(host->dev, "phase error: [map:%016llx]\n", delay);
delay_phase.final_phase = final_phase;
return delay_phase;
}
- while (start < PAD_DELAY_MAX) {
+ while (start < PAD_DELAY_FULL) {
len = get_delay_len(delay, start);
if (len_final < len) {
start_final = start;
len_final = len;
}
start += len ? len : 1;
- if (len >= 12 && start_final < 4)
+ if (!upper_32_bits(delay) && len >= 12 && start_final < 4)
break;
}
/* The rule is that to find the smallest delay cell */
if (start_final == 0)
- final_phase = (start_final + len_final / 3) % PAD_DELAY_MAX;
+ final_phase = (start_final + len_final / 3) % PAD_DELAY_FULL;
else
- final_phase = (start_final + len_final / 2) % PAD_DELAY_MAX;
- dev_dbg(host->dev, "phase: [map:%x] [maxlen:%d] [final:%d]\n",
+ final_phase = (start_final + len_final / 2) % PAD_DELAY_FULL;
+ dev_dbg(host->dev, "phase: [map:%016llx] [maxlen:%d] [final:%d]\n",
delay, len_final, final_phase);
delay_phase.maxlen = len_final;
@@ -1984,30 +2000,68 @@ static inline void msdc_set_cmd_delay(struct msdc_host *host, u32 value)
{
u32 tune_reg = host->dev_comp->pad_tune_reg;
- if (host->top_base)
- sdr_set_field(host->top_base + EMMC_TOP_CMD, PAD_CMD_RXDLY,
- value);
- else
- sdr_set_field(host->base + tune_reg, MSDC_PAD_TUNE_CMDRDLY,
- value);
+ if (host->top_base) {
+ if (value < PAD_DELAY_HALF) {
+ sdr_set_field(host->top_base + EMMC_TOP_CMD, PAD_CMD_RXDLY,
+ value);
This goes up to 92 columns, and it's fine, so fits in one line and it's more
readable like that.
I know that's not your fault, but since you're actually touching those lines
it's a good occasion to also do that (not only here) :-)
Cheers,
Angelo
