On 11/30/23 03:59, Konrad Dybcio wrote:
On 29.11.2023 16:46, Sibi Sankar wrote:
On 11/29/23 18:24, Konrad Dybcio wrote:
On 29.11.2023 10:25, Sibi Sankar wrote:
On 11/18/23 06:36, Konrad Dybcio wrote:
On 17.11.2023 12:39, Sibi Sankar wrote:
From: Rajendra Nayak <quic_rjendra@xxxxxxxxxxx>
Add base dtsi and QCP board (Qualcomm Compute Platform) dts file for
X1E80100 SoC, describing the CPUs, GCC and RPMHCC clock controllers,
geni UART, interrupt controller, TLMM, reserved memory, interconnects,
SMMU and LLCC nodes.
Co-developed-by: Abel Vesa <abel.vesa@xxxxxxxxxx>
Signed-off-by: Abel Vesa <abel.vesa@xxxxxxxxxx>
Signed-off-by: Rajendra Nayak <quic_rjendra@xxxxxxxxxxx>
Co-developed-by: Sibi Sankar <quic_sibis@xxxxxxxxxxx>
Signed-off-by: Sibi Sankar <quic_sibis@xxxxxxxxxxx>
---
[...]
+ idle-states {
+ entry-method = "psci";
+
+ CLUSTER_C4: cpu-sleep-0 {
+ compatible = "arm,idle-state";
+ idle-state-name = "ret";
+ arm,psci-suspend-param = <0x00000004>;
These suspend parameters look funky.. is this just a PSCI sleep
implementation that strays far away from Arm's suggested guidelines?
not really! it's just that 30th bit is set according to spec i.e
it's marked as a retention state.
So, is there no state where the cores actually power down? Or is it
not described yet?
FWIW by "power down" I mean it in the sense that Arm DEN0022D does,
so "In this state the core is powered off. Software on the device
needs to save all core state, so that it can be preserved over
the powerdown."
I was told we mark it explicitly as retention because hw is expected
to handle powerdown and we don't want sw to also do the same.
[...]
+ CPU_PD11: power-domain-cpu11 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ };
+
+ CLUSTER_PD: power-domain-cpu-cluster {
+ #power-domain-cells = <0>;
+ domain-idle-states = <&CLUSTER_CL4>, <&CLUSTER_CL5>;
+ };
So, can the 3 clusters not shut down their L2 and PLLs (if separate?)
on their own?
on CL5 the clusters are expected to shutdown their l2 and PLL on their
own.
Then I think this won't happen with this description
every cpu has a genpd tree like this:
cpu_n
|_CPU_PDn
|_CLUSTER_PD
and CLUSTER_PD has two idle states: CLUSTER_CL4 and CLUSTER_CL5
which IIUC means that neither cluster idle state will be reached
unless all children of CLUSTER_PD (so, all CPUs) go down that low
This is "fine" on e.g. sc8280 where both CPU clusters are part of
the same Arm DynamIQ cluster (which is considered one cluster as
far as MPIDR_EL1 goes) (though perhaps that's misleading and with
the qcom plumbing they perhaps could actually be collapsed separately)
We did verify that the sleep stats increase independently for each
cluster, so it's behavior is unlike what you explained above. I'll
re-spin this series again in the meantime and you can take another
stab at it there.
So are you saying that you checked the RPMh sleep stats and each cluster
managed to sleep on its own, or did you do something different?
We had used some jtag scripts but what you said is correct, there
definitely needs to be separate cluster_pd defined for each cluster.
Will fix this in the next re-spin.
-Sibi
Were the sleep durations far apart? What's the order of magnitude of that
difference? Are the values reported in RPMh greater than those in
/sys/kernel/debug/pm_genpd/power-domain-cpu-cluster/total_idle_time?
Is there any other (i.e. non-Linux) source of "go to sleep" votes?
Konrad
