Add bindings for Renesas R-Car Ethernet TSN End-station IP. The RTSN device provides Ethernet network. Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@xxxxxxxxxxxx> --- .../bindings/net/renesas,ethertsn.yaml | 133 ++++++++++++++++++ 1 file changed, 133 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/renesas,ethertsn.yaml diff --git a/Documentation/devicetree/bindings/net/renesas,ethertsn.yaml b/Documentation/devicetree/bindings/net/renesas,ethertsn.yaml new file mode 100644 index 000000000000..255c8f3a5a3b --- /dev/null +++ b/Documentation/devicetree/bindings/net/renesas,ethertsn.yaml @@ -0,0 +1,133 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/renesas,ethertsn.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas Ethernet TSN End-station + +maintainers: + - Niklas Söderlund <niklas.soderlund@xxxxxxxxxxxx> + +description: + The RTSN device provides Ethernet network using a 10 Mbps, 100 Mbps, or 1 + Gbps full-duplex link via MII/GMII/RMII/RGMII. Depending on the connected PHY. + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,ethertsn-r8a779g0 # R-Car V4H + + reg: + items: + - description: TSN End Station target + - description: generalized Precision Time Protocol target + + reg-names: + items: + - const: tsnes + - const: gptp + + interrupts: + items: + - description: TX data interrupt + - description: RX data interrupt + + interrupt-names: + items: + - const: tx_data + - const: rx_data + + clocks: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + phy-mode: + contains: + enum: + - mii + - rgmii + + phy-handle: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Specifies a reference to a node representing a PHY device. + + renesas,rx-internal-delay: + type: boolean + description: + Enable internal Rx clock delay, typically 1.8ns. + + renesas,tx-internal-delay: + type: boolean + description: + Enable internal Tx clock delay, typically 2.0ns. + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + +patternProperties: + "^ethernet-phy@[0-9a-f]$": + type: object + $ref: ethernet-phy.yaml# + +required: + - compatible + - reg + - reg-names + - interrupts + - interrupt-names + - clocks + - power-domains + - resets + - phy-mode + - phy-handle + - '#address-cells' + - '#size-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a779g0-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a779g0-sysc.h> + #include <dt-bindings/gpio/gpio.h> + + tsn0: ethernet@e6460000 { + compatible = "renesas,ethertsn-r8a779g0"; + reg = <0xe6460000 0x7000>, + <0xe6449000 0x500>; + reg-names = "tsnes", "gptp"; + interrupts = <GIC_SPI 429 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 430 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "tx_data", "rx_data"; + clocks = <&cpg CPG_MOD 2723>; + power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>; + resets = <&cpg 2723>; + + phy-mode = "rgmii"; + renesas,tx-internal-delay; + phy-handle = <&phy3>; + + #address-cells = <1>; + #size-cells = <0>; + + phy3: ethernet-phy@3 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0>; + interrupt-parent = <&gpio4>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio1 23 GPIO_ACTIVE_LOW>; + }; + }; -- 2.42.1
