Re: [PATCH v2 4/9] arm64: dts: ti: k3-am625-beagleplay: Add overlays for OV5640

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 11/17/23 3:28 AM, Jai Luthra wrote:
Three different OV5640 modules are supported using the FFC connector on
BeaglePlay:
- Digilent PCam 5C
- ALINX AN5641
- TEVI-OV5640-*-RPI

The Digilent and ALINX modules supply a 12Mhz XCLK to the sensor, while
the TEVI module supplies a 24Mhz XCLK, thus requiring a separate
overlay.

Signed-off-by: Jai Luthra <j-luthra@xxxxxx>
---
  arch/arm64/boot/dts/ti/Makefile                    | 11 ++++
  .../dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso    | 77 ++++++++++++++++++++++
  .../ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso   | 77 ++++++++++++++++++++++
  3 files changed, 165 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 77a347f9f47d..c6c7825b4cb2 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -12,6 +12,8 @@
  k3-am625-sk-hdmi-audio-dtbs := k3-am625-sk.dtb k3-am62x-sk-hdmi-audio.dtbo
  k3-am62-lp-sk-hdmi-audio-dtbs := k3-am62-lp-sk.dtb k3-am62x-sk-hdmi-audio.dtbo
  dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay-csi2-ov5640.dtbo
+dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay-csi2-tevi-ov5640.dtbo
  dtb-$(CONFIG_ARCH_K3) += k3-am625-phyboard-lyra-rdk.dtb
  dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb
  dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-nonwifi-dahlia.dtb
@@ -80,7 +82,16 @@ dtb-$(CONFIG_ARCH_K3) += k3-j721s2-evm.dtb
  dtb-$(CONFIG_ARCH_K3) += k3-am69-sk.dtb
  dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
+# Build time test only, enabled by CONFIG_OF_ALL_DTBS
+k3-am625-beagleplay-csi2-ov5640-dtbs := k3-am625-beagleplay.dtb \
+	k3-am625-beagleplay-csi2-ov5640.dtbo
+k3-am625-beagleplay-csi2-tevi-ov5640-dtbs := k3-am625-beagleplay.dtb \
+	k3-am625-beagleplay-csi2-tevi-ov5640.dtbo
+dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
+	k3-am625-beagleplay-csi2-tevi-ov5640.dtb
+
  # Enable support for device-tree overlays
+DTC_FLAGS_k3-am625-beagleplay += -@

Too bad the build test check doesn't add this for us, might be time
to just make this default, I see broadcom/Makefile has:

DTC_FLAGS := -@

Well we can look into that later, this patch LGTM,

Reviewed-by: Andrew Davis <afd@xxxxxx>

  DTC_FLAGS_k3-am625-sk += -@
  DTC_FLAGS_k3-am62-lp-sk += -@
  DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso
new file mode 100644
index 000000000000..5e80ca7033ba
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso
@@ -0,0 +1,77 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ALINX AN5641 & Digilent PCam 5C - OV5640 camera module
+ * Copyright (C) 2022-2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+	clk_ov5640_fixed: ov5640-xclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <12000000>;
+	};
+};
+
+&main_gpio0 {
+	p11-hog {
+		/* P11 - CSI2_CAMERA_GPIO1 */
+		gpio-hog;
+		gpios = <11 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "CSI2_CAMERA_GPIO1";
+	};
+};
+
+&wkup_i2c0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	ov5640: camera@3c {
+		compatible = "ovti,ov5640";
+		reg = <0x3c>;
+
+		clocks = <&clk_ov5640_fixed>;
+		clock-names = "xclk";
+
+		port {
+			csi2_cam0: endpoint {
+				remote-endpoint = <&csi2rx0_in_sensor>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
+
+&cdns_csi2rx0 {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		csi0_port0: port@0 {
+			reg = <0>;
+			status = "okay";
+
+			csi2rx0_in_sensor: endpoint {
+				remote-endpoint = <&csi2_cam0>;
+				bus-type = <4>; /* CSI2 DPHY. */
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
+
+&dphy0 {
+	status = "okay";
+};
+
+&ti_csi2rx0 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso
new file mode 100644
index 000000000000..5e1cbbc27c8f
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso
@@ -0,0 +1,77 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Technexion TEVI-OV5640-*-RPI - OV5640 camera module
+ * Copyright (C) 2022-2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+	clk_ov5640_fixed: ov5640-xclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+};
+
+&main_gpio0 {
+	p11-hog {
+		/* P11 - CSI2_CAMERA_GPIO1 */
+		gpio-hog;
+		gpios = <11 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "CSI2_CAMERA_GPIO1";
+	};
+};
+
+&wkup_i2c0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	ov5640: camera@3c {
+		compatible = "ovti,ov5640";
+		reg = <0x3c>;
+
+		clocks = <&clk_ov5640_fixed>;
+		clock-names = "xclk";
+
+		port {
+			csi2_cam0: endpoint {
+				remote-endpoint = <&csi2rx0_in_sensor>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
+
+&cdns_csi2rx0 {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		csi0_port0: port@0 {
+			reg = <0>;
+			status = "okay";
+
+			csi2rx0_in_sensor: endpoint {
+				remote-endpoint = <&csi2_cam0>;
+				bus-type = <4>; /* CSI2 DPHY. */
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
+
+&dphy0 {
+	status = "okay";
+};
+
+&ti_csi2rx0 {
+	status = "okay";
+};





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux