On 11/15/23 3:51 AM, Jai Luthra wrote:
Three different OV5640 modules are supported using the FFC connector on
BeaglePlay:
- Digilent PCam 5C
- ALINX AN5641
- TEVI-OV5640-*-RPI
The Digilent and ALINX modules supply a 12Mhz XCLK to the sensor, while
the TEVI module supplies a 24Mhz XCLK, thus requiring a separate
overlay.
Signed-off-by: Jai Luthra <j-luthra@xxxxxx>
---
arch/arm64/boot/dts/ti/Makefile | 7 ++
.../dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso | 77 ++++++++++++++++++++++
.../ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso | 77 ++++++++++++++++++++++
3 files changed, 161 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 77a347f9f47d..e49e32414560 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -9,9 +9,15 @@
# alphabetically.
# Boards with AM62x SoC
+k3-am625-beagleplay-csi2-ov5640-dtbs := k3-am625-beagleplay.dtb \
+ k3-am625-beagleplay-csi2-ov5640.dtbo
+k3-am625-beagleplay-csi2-tevi-ov5640-dtbs := k3-am625-beagleplay.dtb \
+ k3-am625-beagleplay-csi2-tevi-ov5640.dtbo
k3-am625-sk-hdmi-audio-dtbs := k3-am625-sk.dtb k3-am62x-sk-hdmi-audio.dtbo
k3-am62-lp-sk-hdmi-audio-dtbs := k3-am62-lp-sk.dtb k3-am62x-sk-hdmi-audio.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay-csi2-ov5640.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay-csi2-tevi-ov5640.dtb
We don't need .dtb files for each overlay combination, you should leave these
as overlays only, and just apply them at boot time as needed.
To test apply them at build time, you can use the CONFIG_OF_ALL_DTBS
method that Rob suggested here[0].
# Build time test only, enabled by CONFIG_OF_ALL_DTBS
dtb- += \
k3-am625-beagleplay-overlay-test1.dtb \
k3-am625-beagleplay-overlay-test2.dtb
k3-am625-beagleplay-overlay-test1-dtbs := k3-am625-beagleplay.dtb \
k3-am625-beagleplay-csi2-ov5640.dtbo
k3-am625-beagleplay-overlay-test1-dtbs := k3-am625-beagleplay.dtb \
k3-am625-beagleplay-csi2-tevi-ov5640.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay-csi2-ov5640.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay-csi2-tevi-ov5640.dtbo
[0] https://lore.kernel.org/all/CAL_Jsq+8jisrwEqzz7tZnsV9g2+LmThwpO7sHRFA-zh+6q8XuA@xxxxxxxxxxxxxx/
dtb-$(CONFIG_ARCH_K3) += k3-am625-phyboard-lyra-rdk.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-nonwifi-dahlia.dtb
@@ -81,6 +87,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am69-sk.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
# Enable support for device-tree overlays
+DTC_FLAGS_k3-am625-beagleplay += -@
Having any DTBO applied to the base during build will add symbols to the
base for you, no need to add this line.
(Please check that this is true for the OF_ALL_DTBS case above, I've not
checked yet, we should fix if not).
I plan to remove the same below in later patches so folks will stop adding
more of these lines.
Andrew
DTC_FLAGS_k3-am625-sk += -@
DTC_FLAGS_k3-am62-lp-sk += -@
DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso
new file mode 100644
index 000000000000..5e80ca7033ba
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso
@@ -0,0 +1,77 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ALINX AN5641 & Digilent PCam 5C - OV5640 camera module
+ * Copyright (C) 2022-2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+ clk_ov5640_fixed: ov5640-xclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <12000000>;
+ };
+};
+
+&main_gpio0 {
+ p11-hog {
+ /* P11 - CSI2_CAMERA_GPIO1 */
+ gpio-hog;
+ gpios = <11 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "CSI2_CAMERA_GPIO1";
+ };
+};
+
+&wkup_i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ ov5640: camera@3c {
+ compatible = "ovti,ov5640";
+ reg = <0x3c>;
+
+ clocks = <&clk_ov5640_fixed>;
+ clock-names = "xclk";
+
+ port {
+ csi2_cam0: endpoint {
+ remote-endpoint = <&csi2rx0_in_sensor>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+};
+
+&cdns_csi2rx0 {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ csi0_port0: port@0 {
+ reg = <0>;
+ status = "okay";
+
+ csi2rx0_in_sensor: endpoint {
+ remote-endpoint = <&csi2_cam0>;
+ bus-type = <4>; /* CSI2 DPHY. */
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+};
+
+&dphy0 {
+ status = "okay";
+};
+
+&ti_csi2rx0 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso
new file mode 100644
index 000000000000..5e1cbbc27c8f
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso
@@ -0,0 +1,77 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Technexion TEVI-OV5640-*-RPI - OV5640 camera module
+ * Copyright (C) 2022-2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+ clk_ov5640_fixed: ov5640-xclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ };
+};
+
+&main_gpio0 {
+ p11-hog {
+ /* P11 - CSI2_CAMERA_GPIO1 */
+ gpio-hog;
+ gpios = <11 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "CSI2_CAMERA_GPIO1";
+ };
+};
+
+&wkup_i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ ov5640: camera@3c {
+ compatible = "ovti,ov5640";
+ reg = <0x3c>;
+
+ clocks = <&clk_ov5640_fixed>;
+ clock-names = "xclk";
+
+ port {
+ csi2_cam0: endpoint {
+ remote-endpoint = <&csi2rx0_in_sensor>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+};
+
+&cdns_csi2rx0 {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ csi0_port0: port@0 {
+ reg = <0>;
+ status = "okay";
+
+ csi2rx0_in_sensor: endpoint {
+ remote-endpoint = <&csi2_cam0>;
+ bus-type = <4>; /* CSI2 DPHY. */
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+};
+
+&dphy0 {
+ status = "okay";
+};
+
+&ti_csi2rx0 {
+ status = "okay";
+};
