On 11/8/23 11:28, Conor Dooley wrote:
On Wed, Nov 08, 2023 at 11:24:20AM +0100, Michal Simek wrote:
On 11/8/23 11:12, Conor Dooley wrote:
On Wed, Nov 08, 2023 at 11:06:53AM +0100, Michal Simek wrote:
On 11/7/23 22:18, Conor Dooley wrote:
On Tue, Nov 07, 2023 at 12:09:58PM +0100, Michal Simek wrote:
On 11/6/23 18:07, Conor Dooley wrote:
On Mon, Nov 06, 2023 at 12:53:40PM +0100, Michal Simek wrote:
MicroBlaze V is new AMD/Xilinx soft-core 32bit RISC-V processor IP.
It is hardware compatible with classic MicroBlaze processor. Processor can
be used with standard AMD/Xilinx IPs including interrupt controller and
timer.
Signed-off-by: Michal Simek <michal.simek@xxxxxxx>
---
.../devicetree/bindings/soc/amd/amd.yaml | 26 +++++++++++++++++++
Bindings for SoCs (and by extension boards with them) usually go to in
$arch/$vendor.yaml not into soc/$vendor/$vendor.yaml. Why is this any
different?
I actually found it based on tracking renesas.yaml which describes one of
risc-v board. No problem to move it under bindings/riscv/
That one is kinda a special case, as it contains arm/arm64/riscv.
If they are kinda a special case then what are we?
All AMD/Xilinx platforms(ZynqMP/Versal/Versal NET) can have
arm/arm64/riscv/microblaze cpus(riscv/microblaze as soft cores) in the same
board (IIRC I have also seen xtensa soft core on our chips too).
That would be an argument iff you had all of those in a single file, not
when you only have a single compatible for a riscv "soc" in it.
But DT (compare to System DT) is all the time describing system from cpu
point of view. Or are they describing all that 3 different cpus via the same
DT?
Please look at the contents of renesas.yaml & the commit that moved it
to its current location. I'm only talking about the binding, not any
users.
Thanks for pointer.
" renesas.yaml lists out all the Renesas SoC's and the platforms/EVK's which
is either ARM32/ARM64. It would rather make sense if we move renesas.yaml
to the soc/renesas folder instead. This is in preparation for adding a new
SoC (RZ/Five) from Renesas which is based on RISC-V."
It sounds like boards with arm32 or arm64 or risc-v.
It means I should actually move
Documentation/devicetree/bindings/arm/xilinx.yaml to new location.
In our case we have even systems where you have arm32 (r5 or r52) with arm64
(a53 or a72 or a78) with soft cores (MicroBlaze and later MB-V) on the same board.
Every board which is listed in xilinx.yaml can have MicroBlazes in it.
Thanks,
Michal
--
Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91
w: www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel - Xilinx Microblaze
Maintainer of Linux kernel - Xilinx Zynq ARM and ZynqMP/Versal ARM64 SoCs
U-Boot custodian - Xilinx Microblaze/Zynq/ZynqMP/Versal/Versal NET SoCs
TF-A maintainer - Xilinx ZynqMP/Versal/Versal NET SoCs
