[PATCH 2/2] phy: qcom-qmp-pcie: Add support for keeping refclk always on

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



In PCIe low power states like L1.1 or L1.2 the phy will stop
supplying refclk to endpoint. If endpoint asserts clkreq to bring
back link L0, then RC needs to provide refclk to endpoint.

If there is some issues in platform with clkreq signal propagation
to host and due to that host will not send refclk which results PCIe link
down. For those platforms  phy needs to provide refclk even in low power
states.

Add a flag which indicates refclk is always supplied to endpoint.

Signed-off-by: Krishna chaitanya chundru <quic_krichai@xxxxxxxxxxx>
---
 drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 21 +++++++++++++++++----
 1 file changed, 17 insertions(+), 4 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
index a63ca7424974..d7e377a7d96e 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
@@ -43,6 +43,8 @@
 /* QPHY_PCS_STATUS bit */
 #define PHYSTATUS				BIT(6)
 #define PHYSTATUS_4_20				BIT(7)
+/* PCS_PCIE_ENDPOINT_REFCLK_CNTRL */
+#define EPCLK_ALWAYS_ON_EN			BIT(6)
 
 #define PHY_INIT_COMPLETE_TIMEOUT		10000
 
@@ -77,6 +79,7 @@ enum qphy_reg_layout {
 	QPHY_START_CTRL,
 	QPHY_PCS_STATUS,
 	QPHY_PCS_POWER_DOWN_CONTROL,
+	QPHY_PCS_ENDPOINT_REFCLK_CNTRL,
 	/* Keep last to ensure regs_layout arrays are properly initialized */
 	QPHY_LAYOUT_SIZE
 };
@@ -103,10 +106,11 @@ static const unsigned int sdm845_qhp_pciephy_regs_layout[QPHY_LAYOUT_SIZE] = {
 };
 
 static const unsigned int pciephy_v4_regs_layout[QPHY_LAYOUT_SIZE] = {
-	[QPHY_SW_RESET]			= QPHY_V4_PCS_SW_RESET,
-	[QPHY_START_CTRL]		= QPHY_V4_PCS_START_CONTROL,
-	[QPHY_PCS_STATUS]		= QPHY_V4_PCS_PCS_STATUS1,
-	[QPHY_PCS_POWER_DOWN_CONTROL]	= QPHY_V4_PCS_POWER_DOWN_CONTROL,
+	[QPHY_SW_RESET]				= QPHY_V4_PCS_SW_RESET,
+	[QPHY_START_CTRL]			= QPHY_V4_PCS_START_CONTROL,
+	[QPHY_PCS_STATUS]			= QPHY_V4_PCS_PCS_STATUS1,
+	[QPHY_PCS_POWER_DOWN_CONTROL]		= QPHY_V4_PCS_POWER_DOWN_CONTROL,
+	[QPHY_PCS_ENDPOINT_REFCLK_CNTRL]	= QPHY_V4_PCS_PCIE_ENDPOINT_REFCLK_CNTRL,
 };
 
 static const unsigned int pciephy_v5_regs_layout[QPHY_LAYOUT_SIZE] = {
@@ -2244,6 +2248,8 @@ struct qmp_pcie {
 	struct phy *phy;
 	int mode;
 
+	bool refclk_always_on;
+
 	struct clk_fixed_rate pipe_clk_fixed;
 };
 
@@ -3159,6 +3165,10 @@ static void qmp_pcie_init_registers(struct qmp_pcie *qmp, const struct qmp_phy_c
 	qmp_pcie_configure(pcs, tbls->pcs, tbls->pcs_num);
 	qmp_pcie_configure(pcs_misc, tbls->pcs_misc, tbls->pcs_misc_num);
 
+	if (qmp->refclk_always_on && cfg->regs[QPHY_PCS_ENDPOINT_REFCLK_CNTRL])
+		qphy_setbits(pcs_misc, cfg->regs[QPHY_PCS_ENDPOINT_REFCLK_CNTRL],
+			     EPCLK_ALWAYS_ON_EN);
+
 	if (cfg->lanes >= 4 && qmp->tcsr_4ln_config) {
 		qmp_pcie_configure(serdes, cfg->serdes_4ln_tbl, cfg->serdes_4ln_num);
 		qmp_pcie_init_port_b(qmp, tbls);
@@ -3681,6 +3691,9 @@ static int qmp_pcie_probe(struct platform_device *pdev)
 	if (ret)
 		goto err_node_put;
 
+	qmp->refclk_always_on = of_property_read_bool(dev->of_node,
+						      "qcom,refclk-always-on");
+
 	ret = phy_pipe_clk_register(qmp, np);
 	if (ret)
 		goto err_node_put;

-- 
2.42.0





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux