On Friday 02 January 2015 10:39 PM, Tony Lindgren wrote:
> * Vignesh R <vigneshr@xxxxxx> [141223 23:07]:
>> The charge delay value is by default 0x400. But it can be set to lower
>> values on some boards, as long as false pen-ups are avoided. Lowering the
>> value increases the sampling rate (though current sampling rate is
>> sufficient for TSC operation). In some boards, the value has to be
>> increased to avoid false pen-up events. Hence, charge delay has been
>> made a DT parameter.
>>
>> Signed-off-by: Vignesh R <vigneshr@xxxxxx>
>
> Assuming this binding makes sense for the input people, there should
> be no conflicts merging this patch along with the rest of the series
> via the input tree.
>
I will post new version moving documentation to driver code and keeping
DT changes as a separate patch.
> Sounds like this value probably depends on the size of the touchscreen
> for the capacitance, so a numeric value is really needed here.
Its not just dependent on the size of the touchscreen. It varies based
on the individual setups.
> I would personally prefer generic bindings in general, but in any case
There isn't any generic binding that corresponds to charge-delay.
Nothing as been pointed out by input maintainer either.
Regards
Vignesh
> please feel free to merge along with the other input patches:
>
> Acked-by: Tony Lindgren <tony@xxxxxxxxxxx>
>
>
>> ---
>> v4:
>> - Set charge delay to 0x400 as default. Most devices function normally
>> at this value
>>
>> .../devicetree/bindings/input/touchscreen/ti-tsc-adc.txt | 15 +++++++++++++++
>> arch/arm/boot/dts/am335x-evm.dts | 1 +
>> 2 files changed, 16 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
>> index 878549ba814d..6df5028a4ad3 100644
>> --- a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
>> +++ b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
>> @@ -28,6 +28,20 @@ Required properties:
>> ti,adc-channels: List of analog inputs available for ADC.
>> AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.
>>
>> +Optional properties:
>> +- child "tsc"
>> + ti,charge-delay: Length of touch screen charge delay step in terms of
>> + ADC clock cycles. Charge delay value should be large
>> + in order to avoid false pen-up events. This value
>> + affects the overall sampling speed, hence need to be
>> + kept as low as possible, while avoiding false pen-up
>> + event. Start from a lower value, say 0x400, and
>> + increase value until false pen-up events are avoided.
>> + The pen-up detection happens immediately after the
>> + charge step, so this does in fact function as a
>> + hardware knob for adjusting the amount of "settling
>> + time".
>> +
>> Example:
>> tscadc: tscadc@44e0d000 {
>> compatible = "ti,am3359-tscadc";
>> @@ -36,6 +50,7 @@ Example:
>> ti,x-plate-resistance = <200>;
>> ti,coordiante-readouts = <5>;
>> ti,wire-config = <0x00 0x11 0x22 0x33>;
>> + ti,charge-delay = <0x400>;
>> };
>>
>> adc {
>> diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts
>> index 54f118c08db8..66342515df20 100644
>> --- a/arch/arm/boot/dts/am335x-evm.dts
>> +++ b/arch/arm/boot/dts/am335x-evm.dts
>> @@ -648,6 +648,7 @@
>> ti,x-plate-resistance = <200>;
>> ti,coordinate-readouts = <5>;
>> ti,wire-config = <0x00 0x11 0x22 0x33>;
>> + ti,charge-delay = <0x400>;
>> };
>>
>> adc {
>> --
>> 1.9.1
>>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
