From: Claudiu Beznea <claudiu.beznea.uj@xxxxxxxxxxxxxx>
Add SDHI1 to RZ/G3S Smarc Carrier-II board. This is connected to a uSD
interface. Although Vccq doesn't cross the boundary of SoM it has
been added to RZ/G3S Smarc Carrier-II dtsi to have all the bits related to
SDHI1 in a single place. At the moment SoM is used only with RZ/G3S Smarc
Carrier-II board.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@xxxxxxxxxxxxxx>
---
Changes in v2:
- change regulators' names to regulator-vcc-sdhi1 and
regulator-vccq-sdhi1
arch/arm64/boot/dts/renesas/rzg3s-smarc.dtsi | 65 ++++++++++++++++++++
1 file changed, 65 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/rzg3s-smarc.dtsi b/arch/arm64/boot/dts/renesas/rzg3s-smarc.dtsi
index e7073a09ed2e..214520137230 100644
--- a/arch/arm64/boot/dts/renesas/rzg3s-smarc.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg3s-smarc.dtsi
@@ -11,6 +11,26 @@
/ {
aliases {
serial0 = &scif0;
+ mmc1 = &sdhi1;
+ };
+
+ vcc_sdhi1: regulator-vcc-sdhi1 {
+ compatible = "regulator-fixed";
+ regulator-name = "SDHI1 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&pinctrl RZG2L_GPIO(2, 3) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vccq_sdhi1: regulator-vccq-sdhi1 {
+ compatible = "regulator-gpio";
+ regulator-name = "SDHI1 VccQ";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&pinctrl RZG2L_GPIO(4, 2) GPIO_ACTIVE_HIGH>;
+ gpios-states = <1>;
+ states = <3300000 1>, <1800000 0>;
};
};
@@ -19,6 +39,38 @@ scif0_pins: scif0 {
pinmux = <RZG2L_PORT_PINMUX(6, 3, 1)>, /* RXD */
<RZG2L_PORT_PINMUX(6, 4, 1)>; /* TXD */
};
+
+ sdhi1_pins: sd1 {
+ data {
+ pins = "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3";
+ power-source = <3300>;
+ };
+
+ ctrl {
+ pins = "SD1_CLK", "SD1_CMD";
+ power-source = <3300>;
+ };
+
+ cd {
+ pinmux = <RZG2L_PORT_PINMUX(0, 2, 1)>; /* SD1_CD */
+ };
+ };
+
+ sdhi1_pins_uhs: sd1-uhs {
+ data {
+ pins = "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3";
+ power-source = <1800>;
+ };
+
+ ctrl {
+ pins = "SD1_CLK", "SD1_CMD";
+ power-source = <1800>;
+ };
+
+ cd {
+ pinmux = <RZG2L_PORT_PINMUX(0, 2, 1)>; /* SD1_CD */
+ };
+ };
};
&scif0 {
@@ -26,3 +78,16 @@ &scif0 {
pinctrl-0 = <&scif0_pins>;
status = "okay";
};
+
+&sdhi1 {
+ pinctrl-0 = <&sdhi1_pins>;
+ pinctrl-1 = <&sdhi1_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
+ vmmc-supply = <&vcc_sdhi1>;
+ vqmmc-supply = <&vccq_sdhi1>;
+ bus-width = <4>;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ max-frequency = <125000000>;
+ status = "okay";
+};
--
2.39.2
