Re: [PATCH v2 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 11/10/2023 07:11, Anand Moon wrote:
> Add the binding example for the USB3.1 Genesys Logic GL3523
> integrates with USB 3.1 Gen 1 Super Speed and USB 2.0 High-Speed
> hub.

That's not what the patch does.

> 
> Signed-off-by: Anand Moon <linux.amoon@xxxxxxxxx>
> ---
> New patch.
> ---
>  .../bindings/usb/genesys,gl850g.yaml          | 28 +++++++++++++++++--
>  1 file changed, 25 insertions(+), 3 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml
> index d0927f6768a4..2f6e0c870e1d 100644
> --- a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml
> +++ b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml
> @@ -22,29 +22,51 @@ properties:
>    reg: true
>  
>    reset-gpios:
> +    maxItems: 1

Why?

>      description: GPIO controlling the RESET# pin.
>  
>    vdd-supply:
>      description:
>        the regulator that provides 3.3V core power to the hub.
>  
> +  peer-hub:
> +    $ref: /schemas/types.yaml#/definitions/phandle
> +    description:
> +      phandle to the peer hub on the controller.
> +
>  required:
>    - compatible
>    - reg
> +  - reset-gpios

Why?

> +  - vdd-supply
> +  - peer-hub
>  
>  additionalProperties: false
>  
>  examples:
>    - |
>      #include <dt-bindings/gpio/gpio.h>
> +
>      usb {
>          dr_mode = "host";
>          #address-cells = <1>;
>          #size-cells = <0>;
>  
> -        hub: hub@1 {
> -            compatible = "usb5e3,608";
> +        /* 2.0 hub on port 1 */
> +        hub_2_0: hub@1 {
> +            compatible = "usb5e3,610";
>              reg = <1>;
> -            reset-gpios = <&pio 7 2 GPIO_ACTIVE_LOW>;
> +            vdd-supply = <&vcc_5v>;
> +            peer-hub = <&hub_3_0>;
> +            reset-gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
> +        };
> +
> +        /* 3.1 hub on port 4 */
> +        hub_3_0: hub@2 {
> +            compatible = "usb5e3,620";
> +            reg = <2>;
> +            vdd-supply = <&vcc_5v>;
> +            peer-hub = <&hub_2_0>;
> +            reset-gpios = <&gpio 20 GPIO_ACTIVE_LOW>;

Really, what is happening here?

Best regards,
Krzysztof





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux