Hi, On Tue, Oct 10, 2023 at 5:14 AM Cong Yang <yangcong5@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx> wrote: > > At present, we have found that there may be a problem of blurred > screen during fast sleep/resume. The direct cause of the blurred > screen is that the IC does not receive 0x28/0x10. Because of the > particularity of the IC, before the panel enters sleep hid must > stop scanning, i2c_hid_core_suspend before ili9882t_disable. > This doesn't look very spec-compliant. So in order to solve this > problem, the IC can handle it through the exception mechanism when > it cannot receive 0X28/0X10 command. Handling exceptions requires a reset very nitty, but can you make the "X" lowercase? ...so 0x28 not 0X28. > 50ms delay. Refer to vendor detailed analysis [1]. > > Ilitek vendor also suggested switching the page before entering sleep to > avoid panel IC not receiving 0x28/0x10 command. > > Note: 0x28 is display off, 0x10 is sleep in. > > [1]: https://github.com/ILITEK-LoganLin/Document/tree/main/ILITEK_Power_Sequence > > Signed-off-by: Cong Yang <yangcong5@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx> > --- > drivers/gpu/drm/panel/panel-ilitek-ili9882t.c | 22 ++++++++++++++++++- > 1 file changed, 21 insertions(+), 1 deletion(-) > > diff --git a/drivers/gpu/drm/panel/panel-ilitek-ili9882t.c b/drivers/gpu/drm/panel/panel-ilitek-ili9882t.c > index e095ad91c4bc..20ae370ebe2f 100644 > --- a/drivers/gpu/drm/panel/panel-ilitek-ili9882t.c > +++ b/drivers/gpu/drm/panel/panel-ilitek-ili9882t.c > @@ -465,6 +465,24 @@ static int ili9882t_init_dcs_cmd(struct ili9882t *ili) > return 0; > } > > +static int ili9882t_switch_page(struct mipi_dsi_device *dsi, u8 page) > +{ > + int ret; > + const struct panel_init_cmd cmd = _INIT_SWITCH_PAGE_CMD(page); > + > + ret = mipi_dsi_dcs_write(dsi, cmd.data[0], > + cmd.len <= 1 ? NULL : > + &cmd.data[1], > + cmd.len - 1); > + if (ret) { > + dev_err(&dsi->dev, > + "error switching panel controller page (%d)\n", ret); > + return ret; > + } > + > + return 0; > +} > + > static int ili9882t_enter_sleep_mode(struct ili9882t *ili) > { > struct mipi_dsi_device *dsi = ili->dsi; > @@ -486,8 +504,10 @@ static int ili9882t_enter_sleep_mode(struct ili9882t *ili) > static int ili9882t_disable(struct drm_panel *panel) > { > struct ili9882t *ili = to_ili9882t(panel); > + struct mipi_dsi_device *dsi = ili->dsi; > int ret; > > + ili9882t_switch_page(dsi, 0x00); > ret = ili9882t_enter_sleep_mode(ili); > if (ret < 0) { > dev_err(panel->dev, "failed to set panel off: %d\n", ret); > @@ -548,7 +568,7 @@ static int ili9882t_prepare(struct drm_panel *panel) > gpiod_set_value(ili->enable_gpio, 1); > usleep_range(1000, 2000); > gpiod_set_value(ili->enable_gpio, 0); > - usleep_range(1000, 2000); > + usleep_range(40000, 50000); In response to v1 you said that you actually needed 50 ms here. Oh, I guess that's also in the patch description. The above allows the kernel to delay 40 ms. We need to change it to something that will force the kernel to do 50 ms. That could be: "usleep_range(50000, 51000)", but actually when we're this order of magnitude it should be just "msleep(50)".
