On Sun, 08 Oct 2023 22:54:33 +0530, Anshul Dalal wrote: > A simple driver for a mini gamepad that communicates over i2c, the gamepad > has bidirectional thumb stick input and six buttons. > > The gamepad chip utilizes the open framework from Adafruit called 'Seesaw' > to transmit the ADC data for the joystick and digital pin state for the > buttons. I have only implemented the functionality required to receive the > thumb stick and button state. > > Product page: > https://www.adafruit.com/product/5743 > Arduino driver: > https://github.com/adafruit/Adafruit_Seesaw > > For testing on a RPi Zero 2W, I utilized the following devicetree overlay: > > /dts-v1/; > /plugin/; > / { > compatible = "brcm,bcm2835"; > fragment@0 { > target = <&i2c1>; > __overlay__ { > #address-cells = <1>; > #size-cells = <0>; > joystick@50 { > compatible = "adafruit,seesaw-gamepad"; > reg = <0x50>; > }; > }; > }; > }; > > I used the above overlay as reference for writing this binding. Though the > gamepad also has an interrupt pin that needs to be enabled explicitly (not > currently implemented in driver). The pin triggers a rising edge when a > button is pressed or joystick is moved which can be detected on a GPIO > of the Microcontroller. > > I wasn't sure how to represent that functionality in the binding so I have > left it out for now. > > Signed-off-by: Anshul Dalal <anshulusr@xxxxxxxxx> > --- > > Changes for v2: > - Renamed file to `adafruit,seesaw-gamepad.yaml` > - Removed quotes for `$id` and `$schema` > - Removed "Bindings for" from the description > - Changed node name to the generic name "joystick" > - Changed compatible to 'adafruit,seesaw-gamepad' instead of 'adafruit,seesaw_gamepad' > > .../input/adafruit,seesaw-gamepad.yaml | 51 +++++++++++++++++++ > 1 file changed, 51 insertions(+) > create mode 100644 Documentation/devicetree/bindings/input/adafruit,seesaw-gamepad.yaml > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13): yamllint warnings/errors: dtschema/dtc warnings/errors: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/input/adafruit,seesaw-gamepad.yaml: $id: Cannot determine base path from $id, relative path/filename doesn't match actual path or filename $id: http://devicetree.org/schemas/input/adafruit_seesaw.yaml file: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/input/adafruit,seesaw-gamepad.yaml /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/input/adafruit,seesaw-gamepad.example.dtb: joystick@50: 'reg' does not match any of the regexes: 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/input/adafruit_seesaw.yaml# doc reference errors (make refcheckdocs): See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20231008172435.2391009-1-anshulusr@xxxxxxxxx The base for the series is generally the latest rc1. A different dependency should be noted in *this* patch. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit after running the above command yourself. Note that DT_SCHEMA_FILES can be set to your schema file to speed up checking your schema. However, it must be unset to test all examples with your schema.
