[Question] dt bindings for BeagleConnect

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello everyone, I am working on writing a BeagleConnect driver for Beagleplay board. Let me first go over some terminology:

BeagleConnect is both a technology concept and a line of board designs that implement the technology. Born from Greybus, a mechanism for dynamically extending a Linux system with embedded peripherals, BeagleConnect adds two key elements: a 6LoWPAN transport and mikroBUS manifests. The 6LoWPAN transport provides for arbitrary connections, including the IEEE802.15.4g long-range wireless transport supported between BeaglePlay and BeagleConnect Freedom (the first BeagleConnect board design). The mikroBUS manifests provide for rapid prototyping and low-node-count production with sensor boards following the mikroBUS freely-licensable embedded bus standard, such that existing Linux drivers can be loaded upon Greybus discovery of the nodes.

BeaglePlay consists of a main AM62 processor and a CC1352 co-processor which is responsible for providing 6LoWPAN support along with Greybus node discovery. The AM62 processor and CC1352 are internally connected over UART. The CC1352 coprocessor is supposed to run a specific firmware as a part BeagleConnect setup. It looks as follows:

AM62 (Linux Driver) <--UART--> CC1352 (Zephyr Firmware) <--6LoWPAN--> BeagleConnect Freedom

I need a way to access this bridge UART. The most straightforward method is adding a `compatible` property to the device tree of this UART. But I am not sure how to go about adding a DT binding for it that can be merged upstream.

Here are a few comments I have encountered:

1. DT bindings need to be hardware

I am not sure which hardware the bindings need to target in my case. Should the bindings be serial in nature, since I need to use the UART device? Or they should be about SoC since CC1352 is the device I am actually communicating with? Or maybe there is a 3rd category for an SoC running a specialized firmware for a technology/protocol?

2. DON'T create nodes just for the sake of instantiating drivers.

I guess this means that adding a child node just to add a `compatible` property is not allowed? For some reason, the driver probe is not called if I simply try to override the top level `compatible` property of the serial device. But maybe that is just an issue with my approach?

3. DO attempt to make bindings complete even if a driver doesn't support some features.

This is only relevant if the answer to 1) is the SoC. Since the CC1352 device cannot be directly controlled by, the capability of this device is defined by the firmware running on top of it rather than the hardware. So I am not quite sure what a complete binding for such a device even mean. The only property I can make required would be the `compatible` property and everything else will be optional I guess?


I understand that strict guidelines are required since once a property is added to the Kernel device tree, it will almost be impossible to remove without breaking compatibility. So I would like some guidance or maybe some similar devices that are already a part of the kernel which I can look to for guidance.

Ayush Singh


[BeagleConnect]: https://docs.beagleboard.org/latest/boards/beagleconnect/index.html

[BeaglePlay]: https://docs.beagleboard.org/latest/boards/beagleplay/index.html

[My Last Patch]: https://lists.linaro.org/archives/list/greybus-dev@xxxxxxxxxxxxxxxx/thread/GKOFWZ5IJMNXIWVDOM3WRNU2B2S4244G/

[My Patch Github]: https://github.com/Ayush1325/linux/tree/gb-beagleplay





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux