Hi everyone, This is v3 of my MT6366 PMIC split-out-of-MT6358 cleanup series. The two PMICs are mostly identical, except for the regulator bits. The MT6366 is missing the VCAM* (camera related) LDOs, but in their place has a few other ones. This thus requires a separate compatible to handle the differences. Changes since v2: - Merged "mfd: mt6358: Add registers for MT6366 specific regulators" into "regulator: mt6358: Add missing regulators for MT6366", as suggested by Krzysztof. - Reworked the bindings so that all the regulators are commonly defined, then filtered out by compatible, like every other binding does. - Added some missing end-of-string matches to the LDO patterns - Added patches to reuse the MT6397 regulator binding macros - regulator: dt-bindings: mt6358: Add regulator-allowed-modes property - regulator: mt6358: Use mt6397-regulator.h binding header for buck mode macros - Dropped "regulator-coupled-with" and "regulator-coupled-max-spread" properties from the DT binding example. They don't make much sense without the coupled regulator. - Fixed up selector values in pickable linear ranges Changes since v1: - Switched to using MT6358 compatible as fallback compatible Differences are detected through chip ID register - MT6366 regulator binding merged with MT6358 one instead of having two separate ones - Added patches - regulator: dt-bindings: mt6358: Convert to DT schema - regulator: dt-bindings: mt6358: Add regulator supplies - regulator: mt6358: Add supply names for MT6358 regulators - arm64: dts: mediatek: mt8183-kukui: Add PMIC regulator supplies These bring MT6358 regulators to the same completeness level as MT6366 - Dropped patch "mfd: mt6397: Split MediaTek MT6366 PMIC out of MT6358" - Dropped patch "soc: mediatek: pwrap: add support for MT6366 PMIC" This depends on my previous "regulator: mt6358: Remove bogus regulators and improvements" series [1] and patch "regulator: mt6358: return error for get/set mode op on linear range LDO" [2] patch. These are still in flight, but I think posting this earlier would help get reviews underway. Patch 1 add a compatible string for the MT6366 PMIC, with a fallback to the MT6358 one. This should go through the MFD tree. There are no build time dependencies. Patch 2 converts the existing MT6358 regulator DT binding to DT schema. Patch 3 adds the "regulator-allowed-mode" property to the MT6358 regulator binding. Patch 4 adds regulator supply properties to the MT6358 regulator binding. Patch 5 adds MT6366 regulators to the MT6358 regulator binding. This was previously done by Zhiyong Tao [3] from MediaTek as a separate binding file. I cleaned up the patch based on previous review comments, simplified the regulator names, and added regulator supplies. Bogus regulators were also dropped, like what was done for the MT6358 [1]. In v2 this was merged with the MT6358 binding, now converted to DT schema. Patch 6 makes the MT6358 regulator driver use the mt6397-regulator.h binding header for the operating mode macros. Patch 7 adds support for the regulator supplies to the MT6358 regulator driver. Patch 8 simplifies the MT6366 regulator names to match the new names specified in the binding. Patch 9 makes the MT6366 VCN18 LDO regulator configurable. This is one of the differences between the MT6358 and MT6366. Patch 10 adds regulators that were missing from the originally proposed binding and driver. This includes MFD header changes and needs an ack from Lee. Patch 11 adds regulator supply names to the MT6366 regulators Patch 12 adds regulator supplies to MT8183 Kukui boards. Patch 1 should go through the mfd tree. Patches 3 through 11 should go through the regulator tree after Lee acks patch 10. Patch 12 should go through the MediaTek tree. [1] https://lore.kernel.org/linux-arm-kernel/20230913082919.1631287-1-wenst@xxxxxxxxxxxx/ [2] https://lore.kernel.org/linux-arm-kernel/20230919083647.3909889-1-wenst@xxxxxxxxxxxx/ [3] https://lore.kernel.org/linux-arm-kernel/20220823123745.14061-1-zhiyong.tao@xxxxxxxxxxxx/ Chen-Yu Tsai (11): dt-bindings: mfd: mt6397: Split out compatible for MediaTek MT6366 PMIC regulator: dt-bindings: mt6358: Convert to DT schema regulator: dt-bindings: mt6358: Add regulator-allowed-modes property regulator: dt-bindings: mt6358: Add regulator supplies regulator: mt6358: Use mt6397-regulator.h binding header for buck mode macros regulator: mt6358: Add supply names for MT6358 regulators regulator: mt6358: fix and drop type prefix in MT6366 regulator node names regulator: mt6358: Make MT6366 vcn18 LDO configurable regulator: mt6358: Add missing regulators for MT6366 regulator: mt6358: Add supply names for MT6366 regulators arm64: dts: mediatek: mt8183-kukui: Add PMIC regulator supplies Zhiyong Tao (1): regulator: dt-bindings: mt6358: Add MT6366 PMIC .../devicetree/bindings/mfd/mt6397.txt | 4 +- .../regulator/mediatek,mt6358-regulator.yaml | 247 ++++++++++++ .../bindings/regulator/mt6358-regulator.txt | 350 ------------------ .../arm64/boot/dts/mediatek/mt8183-kukui.dtsi | 28 ++ drivers/regulator/mt6358-regulator.c | 250 +++++++------ include/linux/mfd/mt6358/registers.h | 17 + include/linux/regulator/mt6358-regulator.h | 3 + 7 files changed, 440 insertions(+), 459 deletions(-) create mode 100644 Documentation/devicetree/bindings/regulator/mediatek,mt6358-regulator.yaml delete mode 100644 Documentation/devicetree/bindings/regulator/mt6358-regulator.txt -- 2.42.0.459.ge4e396fd5e-goog
